Rate Limiting | Transition Networks SISGM1040-162D specification

Transition Networks

SISGM1040-162D-LR

Rate Limiting

You can set up every port’s bandwidth rate and frame limitation type.

Ingress Limit Frame type: Select the frame type that you expect to filter. The

frame types have 4 options for selecting: All, Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Broadcast only. Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Bbroadcast only types are selectable for ingress frames. But, the egress rate only supports ’All’ frame type.

Rate Limiting interface

All the ports support ingress and egress rate control which can be selected from 160kbps to 128000kbps. The switch will perform the ingress/egress rate by packet counter to meet the specified rate.

Ingress: Select the port effective ingress rate (The default value is “0”)

Egress: Enter the port effective egress rate (The default value is “0”)

And then, click

Apply

to apply the settings.

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

75

Image 82

Transition Networks SISGM1040-162D manual Rate Limiting, To apply the settings

Contents

SISGM1040-162D V1.01 September Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Content Connecting to the Console Port About Web-based Management Preparing for Web Management Dhcp Server-System configurationDhcp Server-Port and IP Bindings Port Mirroring Rate Limiting Vlan configuration 109 Troubles shooting 112 Technical Specification 113100 110 Port Based Vlan Supports 802.1Q Tag Vlan BenefitsVlan Gvrp Transition Networks SISGM1040-162D-LR Package Contents Physical Dimension Front Panel LED LED IndicatorsTop View PWR PWR2 Off Power input 1 is inactive Green Power input 2 is activeLNK/ACT Wiring the Power Inputs Wiring the Fault Alarm Contact Mounting Installation DIN-Rail Mounting Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Hardware Installation Installation Steps Network Application Ring Application Coupling Ring Application Dual Homing Application Console Management Pin Assignment Login in the Console Interface CLI Management Configure parameters Commands LevelFollowing table lists the CLI commands and description Exec Commands Set List System Commands Set System Name System Description PasswordSystem Location System Contact Hours Subnet maskIP address Full half Port Commands SetPortid 101001000auto Value Enable Disable Trunk Commands Set Valn Vlan Commands SetGroupID Group Name PortNumber Ieee 802.1Q VlanGroupName UntaggedVID ~61440 Spanning Tree Commands SetSeconds Spanning-tree forward Spanning-tree helloTime seconds Stp-path-cost AutoTrueFalse QOS Commands SetWeighted-fairstrict TrueFalse Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set Strings Community Authentication Password PrivacyV1v2cv3v1v2cv3 Community-string Read View Name Write View Name Notify View Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix View Name Port Mirroring Commands Set RXTXBoth Port ID 802.1x Commands SetWords Sec Number Disable reject accept Tftp Commands SetAuthorize Account SystemLog, Smtp and Event Commands SetClientserverboth Index Email address DownBoth Sntp Commands SetLink-UPLink Smtp Minute Start time End timeTimezone Ring Commands Set Web-Based Management About Web-based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration System Event Log-Syslog Configuration To clear all current events log After configuring, click Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR Button to apply the configuration IP SecurityPage User Authentication Button to clean all counts Port Statistics Port Control Port Trunk Aggregator settingTo add the port which is focused to To delete Trunk Group. Select the Group ID and click Aggregator Information State Activity Port state activity will change to Passive Port Mirroring Button To apply the settings Rate Limiting Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rstp System Configuration Rapid Spanning TreePage Rstp Port Configuration Page System Configuration Snmp ConfigurationTo switch to the selected Snmp version mode Page Trap Configuration To add context name. Click SNMPV3 ConfigurationTo remove unwanted context name Page To add context name Click QoS Configuration QoS Policy and Priority TypePage TOS Configuration COS ConfigurationPort Base Priority Igmp Configuration Page Ring To apply the configuration Lldp Configuration 802.1X/Radius Configuration SecurityPage 802.1x Port Configuration Misc Configuration MAC Address Table Use the MAC address table to ensure port securityPage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering Reset switch to default configuration. Click Default value Factory DefaultTo reset all configurations to Save Configuration To save the all Reboot the switch in software reset. Click System RebootTo reboot the system Troubleshooting Technical Specification Snmp MIB CSMA/CD DramPer port Link/Activity Green, Speed 1000M Green EMI Lacp Igmp Sntp 10/100Base-TX Cable Schematic 10 /100BASE-TX Pin outs 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling