Aggregator Information | Transition Networks SISGM1040-162D guide

Transition Networks

SISGM1040-162D-LR

Aggregator Information

When you have setup the aggregator setting with LACP disabled, you will see the local static trunk group information in here.

1.Group Key: Displays the trunk group ID.

2.Port Member: Displays the members of this static trunk group.

Port Trunk – Aggregator Information interface

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

72

Image 79

Transition Networks SISGM1040-162D manual Aggregator Information

Contents

V1.01 September SISGM1040-162D Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Connecting to the Console Port Content About Web-based Management Preparing for Web Management Dhcp Server-System configurationDhcp Server-Port and IP Bindings Port Mirroring Rate Limiting Vlan configuration 110 Troubles shooting 112 Technical Specification 113100 109 Gvrp BenefitsVlan Port Based Vlan Supports 802.1Q Tag Vlan Transition Networks SISGM1040-162D-LR Package Contents Front Panel Physical Dimension PWR LED IndicatorsTop View LED PWR2 Off Power input 1 is inactive Green Power input 2 is activeLNK/ACT Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Mounting Installation Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Installation Steps Hardware Installation Network Application Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Console Management Login in the Console Interface CLI Management Exec Commands LevelFollowing table lists the CLI commands and description Configure parameters System Name Commands Set List System Commands Set System Contact PasswordSystem Location System Description Hours Subnet maskIP address 101001000auto Port Commands SetPortid Full half Value Enable Disable Trunk Commands Set Group Name Vlan Commands SetGroupID Valn UntaggedVID Ieee 802.1Q VlanGroupName PortNumber ~61440 Spanning Tree Commands SetSeconds Stp-path-cost Spanning-tree helloTime seconds Spanning-tree forward TrueFalse QOS Commands SetWeighted-fairstrict AutoTrueFalse Igmp Commands Set Snmp Commands Set Mac / Filter Table Commands Set Community-string Authentication Password PrivacyV1v2cv3v1v2cv3 Strings Community View Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix Read View Name Write View Name Notify View Name RXTXBoth Port Mirroring Commands Set Port ID 802.1x Commands SetWords Number Sec Disable reject accept Tftp Commands SetAuthorize Index Email address SystemLog, Smtp and Event Commands SetClientserverboth Account Smtp Sntp Commands SetLink-UPLink DownBoth Minute Start time End timeTimezone Ring Commands Set About Web-based Management Web-Based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration To clear all current events log After configuring, click System Event Log-Syslog Configuration Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR IP Security Button to apply the configurationPage User Authentication Port Statistics Button to clean all counts Port Control Port Trunk Aggregator settingTo add the port which is focused to To delete Trunk Group. Select the Group ID and click Aggregator Information Port state activity will change to Passive State Activity Button Port Mirroring Rate Limiting To apply the settings Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rapid Spanning Tree Rstp System ConfigurationPage Rstp Port Configuration Page System Configuration Snmp ConfigurationTo switch to the selected Snmp version mode Page Trap Configuration To add context name. Click SNMPV3 ConfigurationTo remove unwanted context name Page To add context name Click QoS Policy and Priority Type QoS ConfigurationPage TOS Configuration COS ConfigurationPort Base Priority Igmp Configuration Page Ring To apply the configuration Lldp Configuration Security 802.1X/Radius ConfigurationPage 802.1x Port Configuration Misc Configuration Use the MAC address table to ensure port security MAC Address TablePage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering Reset switch to default configuration. Click Default value Factory DefaultTo reset all configurations to To save the all Save Configuration Reboot the switch in software reset. Click System RebootTo reboot the system Troubleshooting Snmp MIB Technical Specification CSMA/CD DramPer port Link/Activity Green, Speed 1000M Green EMI Igmp Lacp Sntp 10 /100BASE-TX Pin outs 10/100Base-TX Cable Schematic 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling