CLI Management | Transition Networks SISGM1040-162D instruction

Transition Networks

SISGM1040-162D-LR

Console login interface

CLI Management

The system supports a command line interface management–CLI. After you have logged in the system by typing in user name and password, you will see a command prompt. To enter CLI management interface, enter “enable” command.

CLI command interface

Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

19

Image 26

Transition Networks SISGM1040-162D manual CLI Management

Contents

SISGM1040-162D V1.01 September Firmware Version V1.01 Kernel Version V1.80 Hardware Version FCC Warning Content Connecting to the Console Port Dhcp Server-Port and IP Bindings Dhcp Server-System configurationAbout Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 109 Troubles shooting 112 Technical Specification 113100 110 Port Based Vlan Supports 802.1Q Tag Vlan BenefitsVlan Gvrp Transition Networks SISGM1040-162D-LR Package Contents Physical Dimension Front Panel LED LED IndicatorsTop View PWR LNK/ACT Off Power input 1 is inactive Green Power input 2 is activePWR2 Wiring the Power Inputs Wiring the Fault Alarm Contact Mounting Installation DIN-Rail Mounting Transition Networks SISGM1040-162D-LR Wall Mount Plate Mounting Hardware Installation Installation Steps Network Application Ring Application Coupling Ring Application Dual Homing Application Console Management Pin Assignment Login in the Console Interface CLI Management Configure parameters Commands LevelFollowing table lists the CLI commands and description Exec Commands Set List System Commands Set System Name System Description PasswordSystem Location System Contact IP address Subnet maskHours Full half Port Commands SetPortid 101001000auto Value Enable Disable Trunk Commands Set Valn Vlan Commands SetGroupID Group Name PortNumber Ieee 802.1Q VlanGroupName UntaggedVID Seconds Spanning Tree Commands Set~61440 Spanning-tree forward Spanning-tree helloTime seconds Stp-path-cost AutoTrueFalse QOS Commands SetWeighted-fairstrict TrueFalse Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set Strings Community Authentication Password PrivacyV1v2cv3v1v2cv3 Community-string Read View Name Write View Name Notify View Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix View Name Port Mirroring Commands Set RXTXBoth Words 802.1x Commands SetPort ID Sec Number Authorize Tftp Commands SetDisable reject accept Account SystemLog, Smtp and Event Commands SetClientserverboth Index Email address DownBoth Sntp Commands SetLink-UPLink Smtp Timezone Start time End timeMinute Ring Commands Set Web-Based Management About Web-based Management System Login Main System Information IP Configuration Dhcp Server-System configuration Dhcp Client-Client Entries Dhcp Server-Port and IP Bindings TFTP-Update Firmware TFTP-Restore Configuration TFTP-Backup Configuration System Event Log-Syslog Configuration To clear all current events log After configuring, click Apply Technical Support International Page System Event Log-Event Configuration Page Fault Relay Alarm Sntp Configuration Transition Networks SISGM1040-162D-LR Transition Networks SISGM1040-162D-LR Button to apply the configuration IP SecurityPage User Authentication Button to clean all counts Port Statistics Port Control To add the port which is focused to Aggregator settingPort Trunk To delete Trunk Group. Select the Group ID and click Aggregator Information State Activity Port state activity will change to Passive Port Mirroring Button To apply the settings Rate Limiting Vlan configuration Vlan configuration-Port-based Vlan Button to modify existing Vlan group 802.1Q Vlan 802.1Q Configuration You can Change the Vlan group name and Vlan ID Click Rstp System Configuration Rapid Spanning TreePage Rstp Port Configuration Page To switch to the selected Snmp version mode Snmp ConfigurationSystem Configuration Page Trap Configuration To remove unwanted context name SNMPV3 ConfigurationTo add context name. Click Page To add context name Click QoS Configuration QoS Policy and Priority TypePage Port Base Priority COS ConfigurationTOS Configuration Igmp Configuration Page Ring To apply the configuration Lldp Configuration 802.1X/Radius Configuration SecurityPage 802.1x Port Configuration Misc Configuration MAC Address Table Use the MAC address table to ensure port securityPage MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering To reset all configurations to Factory DefaultReset switch to default configuration. Click Default value Save Configuration To save the all To reboot the system System RebootReboot the switch in software reset. Click Troubleshooting Technical Specification Snmp MIB Per port Link/Activity Green, Speed 1000M Green DramCSMA/CD EMI Lacp Igmp Sntp 10/100Base-TX Cable Schematic 10 /100BASE-TX Pin outs 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Gigabit Copper/SFP mini-GBIC combo port Transceiver to the SFP slot 10 LC connector to the transceiver 123 11 Remove LC connector Cabling