Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology PV100S-480 installation manual WARNING Shock Hazard, 3 On/Off Switch

Models: PV100S-480

1 90

Download 90 pages 29.08 Kb

Page 28

On/Off Switch

Introduction

WARNING: Shock Hazard

Disengaging the main enclosure door interlock switch does NOT remove all hazardous voltages from inside the inverter. Before attempting to service the PV100S, follow the de-energize Lockout and Tag procedure on page x.

On/Off Switch

The PV100S incorporates a maintained position ON/OFF switch located on the front door of the main enclosure. Under normal conditions, the ON/OFF switch is in the ON position. Turning the switch to the OFF position will initiate an immediate controlled shutdown of the PV100S and opens both the main AC and DC contactors within the unit. The main AC and DC contactors cannot be closed unless the switch is in the ON position. The PV100S is prevented from being restarted until the ON/OFF switch is turned back to the ON position.

WARNING: Shock Hazard

Turning the ON/OFF switch to the OFF position does NOT remove all hazardous voltages from inside the inverter. Before attempting to service the PV100S, follow the de-energize Lockout and Tag procedure on page x.

Figure 1-3On/Off Switch

1–8	152315 Rev C

Image 28

Xantrex Technology PV100S-480 installation manual WARNING Shock Hazard, 3 On/Off Switch

Contents

PV100S 100 kW Grid-Tied Photovoltaic Inverter Planning and Installation ManualPV100S-208 PV100S-480 Page Planning and Installation Manual PV100S 100 kW Grid-Tied Photovoltaic InverterAbout Xantrex TrademarksNotice of Copyright DisclaimerAbout This Manual PurposeScope AudienceConventions Used Abbreviations and Acronyms Related InformationPage Important Safety Instructions SAVE THESE INSTRUCTIONS - DO NOT DISCARDWARNING Shock Hazard WARNING Lethal VoltageGeneral Safety Precautions Personal SafetySafety Equipment Wiring RequirementsCAUTION Fire Hazard Lockout and Tag Operational Safety ProceduresWARNING Shock Hazard Interconnection Standards Compliance De-Energize/Isolation ProcedureTo isolate the PV100S Page 1 Introduction Contents2 Planning 3 Installation A Schematics4 Verification Verification Procedure SummaryTables Page Figures Figure 3-18 AC Terminal Connections from the Utility- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3-18 Figure 3-19 PV Array Cable Routing and Terminations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3-19 Figure 3-20 Telephone Cable Routing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3-21 Figure 3-21 RS232/FO Converter Kit Installation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3-23 Figure 3-22 Direct Connect Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3-24 Figure A-1 Electrical Diagram sample- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A-3 Figure A-2 PV100S-480 Schematic for Main Power Distribution 152316 E1 - - - - - - - - - - - - - - A-4 Figure A-3 PV100S-480 Schematic for Control Power Distribution 152316 E2 - - - - - - - - - - - - - A-5 Figure A-4 PV100S-480 Schematic for Converter Control Unit 152316 E3- - - - - - - - - - - - - - - - A-6 Figure A-5 PV100S-208 Schematic Main Power Distribution 152376 C1 - - - - - - - - - - - - - - - - - A-7 Figure A-6 PV100S-208 Schematic for Control Power Distribution 152376 C2 - - - - - - - - - - - - - A-8 Figure A-7 PV100S-208 Schematic for Converter Control Unit 152376 C3- - - - - - - - - - - - - - - - A-9 1 Introduction Description of the PV100S Figure 1-1 Dimensions Not to scale 49 7/8 124.8 cm60 ¼ 150.5 cm 59 ¼ 148 cmSystem Specifications Electrical SpecificationsCAUTION Equipment Damage Over Voltage, Under Voltage and Frequency RangesSystem Ground Requirements System Neutral RequirementsUtility Side Isolation Transformer Requirements CAUTION Equipment DamageEnvironmental Specifications Table 1-3 Environmental SpecificationsIn front of access doors 36 in 91 cm In front of access panels 36 in 91 cmMain Enclosure Door Interlock Switch Operator Interface ControlsOn/Off Switch Figure 1-3 On/Off SwitchWARNING Shock Hazard WARNING Shock HazardCommunication Features AC and DC Disconnect SwitchesSystem Status and Fault Reporting Data LoggingCommunication Methods Universal Front Panel Control Unit UFCUPC Connection Methods Wireless Access POTS AccessFigure 1-7 POTS Access Ethernet LAN Access Direct AccessFigure 1-9 Ethernet LAN Access Figure 1-10 Direct Access2 Planning Overview of PV100S Installation WARNING Shock HazardVentilation and Serviceability Requirements PV PlanningGround Requirements System Neutral RequirementsCommunication Requirements Utility Side Isolation Transformer RequirementsElectrical Diagrams and Schematics CAUTION Equipment DamageWARNING Lethal Voltage Model PV100S-480Layout Options Figure 2-1 PV100S Layout Option AMinimum Dimension of Base Approximately 9 ft by 7 ft 2.7 m x 2.1 m Figure 2-2 PV100S Layout Option BConduit Penetration Figure 2-3 Conduit Entry Figure Reference6 15 cm 2 5 cm 12 30 cm 6 15 cm2 5 cm 6 15 cm 12 30 cmFigure 2-7 DC Interface Enclosure, Bottom Side Figure 2-6 AC Interface Enclosure Conduit Entry, Left SideFigure 2-8 Communications Enclosure Conduit Entry, Bottom Side Conductor and Conduit Sizing CAUTION Equipment DamageTo calculate the proper conduit size Step 1. Determine the required cable ampacitySense/Control Wires Step 3. Size the cableStep 4. Size the conduit DLO 3/0 AWG CableAnchoring the PV100S 29 73.7 cm5/8 1.5 cm x4 16 ¼ 40.6 cmFigure 2-10 AC Interface/Transformer Anchor Bolt Pattern Not to Scale 17 ½73.7 cm 44 cm63.5 cm ¾ 1.9 cm x6 Planning3 Installation Unloading Equipment RequiredWARNING Heavy Equipment Moving the PV100S Unpacking the PV100SCAUTION Equipment Damage To move the PV100S while it is still inside the shipping cratesRemoving the Pallet and Moving the PV100S CAUTION Equipment Damage Lift HereTo move the PV100S using a forklift Lift HereMounting and Anchoring the Units To mount and anchor the PV100SOpening or Closing Access Doors Figure 3-4 Inverter Enclosure Access DoorsInstallation To lock or unlock the front door on the main inverterTo Open Access Door To Close Access DoorFigure 3-5 AC Interface Access Door To Open Access DoorFigure 3-7 Transformer Access Panels Figure 3-8 Inductor Access PanelsInstallation Transformer Access PanelConduit Installation To install the conduitsWiring - General WARNING Shock HazardWARNING Lethal Voltage CAUTION Equipment DamageOvercurrent Protection Conductor TerminationCAUTION Equipment Damage See Figure 3-14 on page 3-15 for the location of these terminalsWire Gauge and Torque Requirements GroundingUtility Side Isolation Transformer Requirements System Neutral RequirementsFigure 3-11 Chassis Ground Bar TB1 Wiring - Specific AC ConnectionsTo connect the main inverter to AC interface/transformer assembly CAUTION Equipment DamageFigure 3-13 Tie-wraps on the AC Sense Harness Transformer EnclosureA phase C phaseB phase Figure 3-15 AC Terminal Connections in the Main Inverter EnclosureTo connect the utility service to AC Interface Enclosure CAUTION Equipment DamageS1-2T1 A Phase terminal S1-6T3 C Phase terminalS1-4T2 B Phase terminal TB6 Neutral Ground TB2 Figure 3-18 AC Terminal Connections from the UtilityPV Array Connections Figure 3-19 PV Array Cable Routing and TerminationsPC Communications PC Connection MethodsEstablishing a POTS Connection To connect a personal computer using the POTS ConnectionEstablishing Wireless Connection Establishing an Ethernet LAN ConnectionTo connect a personal computer using the GSM Wireless modem To connect a personal computer using the Ethernet LAN ConnectionDirect Connection If connecting the PC directly to the inverterFigure 3-22 Direct Connect Installation Installation3-24 152315 Rev C4 Verification Verification Procedure Summary WARNING Electrocution HazardInspect the following items prior to completion of the installation WARNING Shock HazardVisual Inspection of Mechanical Connections Visual Inspection of Electrical ConnectionsTo perform a visual inspection of the PV100S mechanical connections To perform a visual inspection of the PV100S electrical connectionsVisual Inspection, Isolation Transformer Wye/Wye Corrective ActionTo perform a visual inspection of the Isolation Transformer Wye/Wye Perform after initial inspection if requiredA Schematics Appendix A contains useful schematics to aid with installationSchematics This page intentionally left blank152315 Rev C Figure A-1 Electrical Diagram sample SchematicsAppendix A 152315 Rev CFigure A-2 PV100S-480 Schematic for Main Power Distribution 152316 E1 Schematics152315 Rev C Appendix AAppendix A Schematics152315 Rev C Figure A-4 PV100S-480 Schematic for Converter Control Unit 152316 E3 Schematics152315 Rev C Appendix AFigure A-5 PV100S-208 Schematic Main Power Distribution 152376 C1 SchematicsAppendix A 152315 Rev C152315 Rev C SchematicsAppendix A Figure A-7 PV100S-208 Schematic for Converter Control Unit 152376 C3 SchematicsAppendix A 152315 Rev CSchematics This page was intentionally left blankA-10 152315 Rev CIndex Page Page Xantrex Technology Inc 1 800 670 0707 Tel toll free NA 1 360 925 5097 Tel direct152315 Rev C Printed in USA