Cases to update firmware from console | Xerox NS-2260 instruction

6. Update Firmware from Console

The switch also supports firmware update from console port. The operation is performed over 1K Xmodem protocol.

Cases to update firmware from console:

1.Power on the switch and press any key from console within 5 seconds. The switch enters 1K Xmodem receiver mode.

2.The switch enters 1K Xmodem receiver mode automatically when it detects firmware checksum error while booting.

Setup 1K Xmodem on Hyper Terminal

1. Press [Disconnect] to stop Hyper Terminal.

2. 1K Xmodem only works on 57600 baudrate. Enter File -> Property to set COM port for baudrate 57600, 8 data bit, None parity, 1 stop bit, No flow control.

3.Press [Connect] to reconnect to the switch.

4.Enter Transfer -> Send File command.

5.Specify the file name of the firmware image file.

6.Specify 1K Xmodem protocol.

7.Click [Send] button to start file transfer.

When finishing downloading image, the switch will update firmware automatically and reboot. Change COM port baudrate back to to 9600bps.

Image 146

Xerox NS-2260 operation manual Cases to update firmware from console, Setup 1K Xmodem on Hyper Terminal

Contents

NS-2260 Optional 100FX Modules Optional Gigabit Modules Trademarks Console and Telnet Operation Table of ContentsInstallation and Management Snmp Management Update Firmware from Console Appendix a Factory Default Settings Introduction Introduction Features Supports Ethernet frame length up to 1522 bytes Hardware Specifications Gvrp Speed status Software Specifications Management Objects Management Objects Console TelnetWeb Trap Events Type Trap Event Rules of trunking Lacp disabledLacp enabled IP Multicast Function IP Multicast address Igmp MAC Address Filtering Function Igmp SnoopingMulticast Forwarding Static MAC Address Port Security Vlan Function Port-based Vlan Spanning Tree Protocol Ieee 802.1Q Vlan Tag-based VlanProtocol-based Vlan Spanning tree port states Per port control settingsSTP related parameters Port Sniffer FunctionPage Priority Classification Methods Outgoing Service PolicyQoS Priority Function 10 802.1X Port-Based Network Access Control Misc. configuration Enable 802.1X protocol Radius client configurationPer-port 802.1X mode setting Installation and Management Panel Description AC Power Supply 1 10/100TX Ports Network Switched PortsPort Number Label Specifications Port Type Speed Compliance Cables Distance JP1 setting 2 100FX Modules Installation steps Part Number Connector CableSpecifications Gigabit Ports and Modules Cable Distance Specifications Part Number Compliance Speed Duplex Part Number Wavelength Giga Port Module Installation steps Rack Mounting LED Indicators LED Name State Interpretation System LEDs Cooling Fans Management Setup Setup for Out-of-band Console Management Setup for In-band Management Quick Guide to Configure Switch IP Address Power-on Self-test Console message Cold Start Telnet Management Login PromptDirect Console Management When login successfully, the main menu is shown as follows Main Menu Save Action menu QuitEdit Previous Switch Static Configuration Switch Static Configuration menu is shown as follows Port Configuration Managed 24+2G Switch Port ConfigurationPage Trunk Configuration Trunk configuration example Managed 24+2G Switch Trunk Configuration Vlan Configuration Vlan Configure Vlan Mode 802.1Q Create a Vlan Group Create a Port-based Vlan group Create an 802.1Q Vlan PORT4 PORT5 PORT6 PORT7 PORT8 Edit / Delete a Vlan Group Example to select one Vlan group for editing or deleting Groups Sorted Mode Example to edit Vlan2 group Misc Configuration MAC Age Interval Broadcast Storm Filtering Max Bridge Transmit Delay Bound Managed 24+2G Switch Port Security Collision Retry Forever Hash Algorithm Administration Configuration Change Username Change Password Device Information IP Configuration Port Sniffer Configuration Priority Configuration Static Priority High/Low Queue Service Ratio = Hx Lx, where x = 1~7 7.2 802.1p Priority MAC Address Configuration Add static MAC address Select one static MAC address to edit or delete Filtering MAC Address Example to enter a new filter address Protocol Related Configuration 1 STP STP Enable System Configuration Perport Configuration Snmp System Options Community Strings Add/Edit a Community String Trap Managers Add/Edit a trap manager Gvrp Igmp Working Port Setting Lacp State Activity Lacp Status This page shows Lacp status of each trunk group Enable 802.1X Protocol 6.2 802.1X System Configuration 6.3 802.1X Per Port Configuration 6.4 802.1X Misc. Configuration Managed 24+2G Switch 802.1x Misc Configuration Status and Counters Port Status Managed 24+2G Switch Port Counters Port Counters System Information Restart Reboot SwitchDefault Tftp Update Firmware Main Menu Reboot Switch Restart Tftp Restore Configuration Tftp Backup Configuration Snmp Management Port MIB-2 Objects Set/Get Value Options Configuring Snmp Settings via Console OperationSnmp MIB-2 and Private MIB Private MIB Objects Set/Get Value Options Snmp Traps Trap Name RFC1157 Event of Trap Generated Set IP Address for the device unit Best Display Resolution 1024 x 768 pixels upWeb Browser Start Browser Software and Making Connection Web Management Home Overview Config / Atual Page Port Statistics Administrator IP Address Switch Setting Basic Information Module Info Advanced Page Console Port Information Parity Check none Stop Bits Flow control none Port Controls Page Trunking Aggregator settings Aggregator Information Two Static Trunking groups are configured Page State Activity Forwarding and Filtering Database 5.5.6.1 Igmp Snooping Static MAC Address MAC Address Filtering Port Based Vlan Port-based Vlan Page 7.2 802.1Q Vlan Add a new Vlan Page Ingress Filtering Rule 2 Drop Untagged Frame Spanning Tree Page Page Page Port Sniffer Snmp Parameters Snmp Managers Snmp Trap Managers Assign/Change password Type the new password Security Manager 12 802.1X Configuration System Configuration 12.1 802.1X PerPort Configuration 12.2 802.1X Misc Configuration Stack Settings Page Stacking Page Tftp Update Firmware Page Configuration Backup Tftp Restore Configuration Tftp Backup Configuration Reset System Reboot Cases to update firmware from console Setup 1K Xmodem on Hyper Terminal Appendix a Factory Default Settings Not available NASL2SWITCH