Port Configuration | Xerox NS-2260 specification

3.2.1 Port Configuration

The following page illustrates Port 1 ~ Port 8 configuration example:

-------------------------------------------------------------------------

Managed 24+2G Switch : Port Configuration

		InRate	OutRate					FlowControl
Port	Type (100K) (100K)			Enable Auto Spd/Dpx			Full		Half
------------------------------------------------------------------
PORT1	100TX	0	0	Yes	AUTO	100 FULL		On	On
PORT2	100TX	0	0	Yes	AUTO	100 FULL		On	On
PORT3	100TX	0	0	Yes	AUTO	100 FULL		On	On
PORT4	100TX	0	0	Yes	AUTO	100 FULL		On	On
PORT5	100TX	0	0	Yes	AUTO	100 FULL		On	On
PORT6	100TX	0	0	Yes	AUTO	100 FULL		On	On
PORT7	100TX	0	0	Yes	AUTO	100 FULL		On	On
PORT8	100TX	0	0	Yes	AUTO	100 FULL		On	On
action-> <Quit> <Edit>			<Save>		<Previous Page>		<Next Page>
------------------------------------------------------------------
Tab=Next Item BackSpace=Previous Item Quit=Previous Menu Enter= Select Item

-------------------------------------------------------------------------

Image 42

Xerox NS-2260 operation manual Managed 24+2G Switch Port Configuration

Contents

NS-2260 Optional 100FX Modules Optional Gigabit Modules Trademarks Table of Contents Installation and ManagementConsole and Telnet Operation Snmp Management Update Firmware from Console Appendix a Factory Default Settings Introduction Introduction Features Supports Ethernet frame length up to 1522 bytes Hardware Specifications Gvrp Speed status Software Specifications Management Objects Management Objects Console TelnetWeb Trap Events Type Trap Event Lacp disabled Lacp enabledRules of trunking IP Multicast Function IP Multicast address Igmp Igmp Snooping Multicast ForwardingMAC Address Filtering Function Static MAC Address Port Security Vlan Function Port-based Vlan Ieee 802.1Q Vlan Tag-based Vlan Protocol-based VlanSpanning Tree Protocol Spanning tree port states Per port control settingsSTP related parameters Port Sniffer FunctionPage Outgoing Service Policy QoS Priority FunctionPriority Classification Methods 10 802.1X Port-Based Network Access Control Enable 802.1X protocol Radius client configuration Per-port 802.1X mode settingMisc. configuration Installation and Management Panel Description AC Power Supply 1 10/100TX Ports Network Switched PortsPort Number Label Specifications Port Type Speed Compliance Cables Distance JP1 setting 2 100FX Modules Part Number Connector Cable SpecificationsInstallation steps Gigabit Ports and Modules Cable Distance Specifications Part Number Compliance Speed Duplex Part Number Wavelength Giga Port Module Installation steps Rack Mounting LED Indicators LED Name State Interpretation System LEDs Cooling Fans Management Setup Setup for Out-of-band Console Management Setup for In-band Management Quick Guide to Configure Switch IP Address Power-on Self-test Console message Cold Start Login Prompt Direct Console ManagementTelnet Management When login successfully, the main menu is shown as follows Main Menu Save Action menu QuitEdit Previous Switch Static Configuration Switch Static Configuration menu is shown as follows Port Configuration Managed 24+2G Switch Port ConfigurationPage Trunk Configuration Trunk configuration example Managed 24+2G Switch Trunk Configuration Vlan Configuration Vlan Configure Vlan Mode 802.1Q Create a Vlan Group Create a Port-based Vlan group Create an 802.1Q Vlan PORT4 PORT5 PORT6 PORT7 PORT8 Edit / Delete a Vlan Group Example to select one Vlan group for editing or deleting Groups Sorted Mode Example to edit Vlan2 group Misc Configuration MAC Age Interval Broadcast Storm Filtering Max Bridge Transmit Delay Bound Managed 24+2G Switch Port Security Collision Retry Forever Hash Algorithm Administration Configuration Change Username Change Password Device Information IP Configuration Port Sniffer Configuration Priority Configuration Static Priority High/Low Queue Service Ratio = Hx Lx, where x = 1~7 7.2 802.1p Priority MAC Address Configuration Add static MAC address Select one static MAC address to edit or delete Filtering MAC Address Example to enter a new filter address Protocol Related Configuration 1 STP STP Enable System Configuration Perport Configuration Snmp System Options Community Strings Add/Edit a Community String Trap Managers Add/Edit a trap manager Gvrp Igmp Working Port Setting Lacp State Activity Lacp Status This page shows Lacp status of each trunk group Enable 802.1X Protocol 6.2 802.1X System Configuration 6.3 802.1X Per Port Configuration 6.4 802.1X Misc. Configuration Managed 24+2G Switch 802.1x Misc Configuration Status and Counters Port Status Managed 24+2G Switch Port Counters Port Counters System Information Reboot Switch DefaultRestart Tftp Update Firmware Main Menu Reboot Switch Restart Tftp Restore Configuration Tftp Backup Configuration Snmp Management Configuring Snmp Settings via Console Operation Snmp MIB-2 and Private MIBPort MIB-2 Objects Set/Get Value Options Private MIB Objects Set/Get Value Options Snmp Traps Trap Name RFC1157 Event of Trap Generated Best Display Resolution 1024 x 768 pixels up Web BrowserSet IP Address for the device unit Start Browser Software and Making Connection Web Management Home Overview Config / Atual Page Port Statistics Administrator IP Address Switch Setting Basic Information Module Info Advanced Page Console Port Information Parity Check none Stop Bits Flow control none Port Controls Page Trunking Aggregator settings Aggregator Information Two Static Trunking groups are configured Page State Activity Forwarding and Filtering Database 5.5.6.1 Igmp Snooping Static MAC Address MAC Address Filtering Port Based Vlan Port-based Vlan Page 7.2 802.1Q Vlan Add a new Vlan Page Ingress Filtering Rule 2 Drop Untagged Frame Spanning Tree Page Page Page Port Sniffer Snmp Parameters Snmp Managers Snmp Trap Managers Assign/Change password Type the new password Security Manager 12 802.1X Configuration System Configuration 12.1 802.1X PerPort Configuration 12.2 802.1X Misc Configuration Stack Settings Page Stacking Page Tftp Update Firmware Page Configuration Backup Tftp Restore Configuration Tftp Backup Configuration Reset System Reboot Cases to update firmware from console Setup 1K Xmodem on Hyper Terminal Appendix a Factory Default Settings Not available NASL2SWITCH