Manuals / Xerox / Computer Equipment / Switch

Xerox NS-2260 operation manual Advanced

Models: NS-2260

1 149

Download 149 pages 61.72 Kb

Page 102

5.5.2.3 Advanced

5.5.2.3 Advanced

Miscellaneous settings :

MAC Address Age-out Time : Type the number of seconds that an inactive MAC address remains in the switch address table. The valid range is 300~765 seconds (must be multiple of 3). Default is 300 seconds.

Max bridge transmit delay bound control : Limit the packets queuing time in switch. If enabled and queuing time expired,thequeuedpacketswillbedropped. Options - OFF (default), 1sec, 2sec, 4sec

Enable Low Queue Delay Bound : setting to limit the low priority packets queuing time in switch. If enabled and queuing time expired, the low priority packets queued in switch will be sent.

Note: Make sure Max bridge transit delay bound control is enabled when Low Queue Delay Bound control is set to ENABLE.

Max. Delay Time : max. low queuing time, value range 1 ~ 255 (2ms/unit)

Broadcast Storm Filter Mode : To configure broadcast storm control, enable it and set the upper threshold applied to all ports. The threshold is the percentage of the port total bandwidth used by broadcast traffic. When broadcast traffic for a port rises above the threshold set, broadcast storm protection becomes active. The valid threshold values are 5%, 10%, 15%, 20%, 25% and Off.

Image 102

Xerox NS-2260 operation manual Advanced

Contents

Operation Manual NS-2260 Optional 100FX ModulesOptional Gigabit Modules TRADEMARKS NOTICECISPR A COMPLIANCE 3. Console and Telnet Operation Table of Contents2. Installation and Management 1. Introduction4. SNMP Management 5. Web Management6. Update Firmware from Console Appendix A: Factory Default Settings1. Introduction 1.1 Introduction1.2 Features 1.3 Hardware Specifications Power Consumption DimensionPower Input Rating Operating temperature : 0 ~ 50oC1.4 Software Specifications Console TelnetWeb 1.4.1 Management ObjectsManagement Objects SNMPConsole TelnetWeb 1.4.2Management Objects SNMPLACP disabled LACP enabledRules of trunking 1.5.2 IP Multicast Function IP Multicast addressIGMP 1.5.3 MAC Address Filtering Function IGMP SnoopingMulticast Forwarding 1.5.4 Static MAC Address 1.5.5 Port Security1.5.6 VLAN Function 1.5.6.1 Port-basedVLAN1.5.6.2 IEEE 802.1Q VLAN Tag-basedVLAN 1.5.6.3 Protocol-basedVLAN1.5.7 Spanning Tree Protocol STP related parameters 1.5.8 Port Sniffer FunctionPer port control settings Spanning tree port statesPage 1.5.9 QoS Priority Function Outgoing Service PolicyPriority Classification Methods 1.5.10 802.1X Port-BasedNetwork Access Control Per-port802.1X mode setting Enable 802.1X protocolRadius client configuration Misc. configuration2. Installation and Management 2.1 Panel Description 2.2 AC Power SupplySpecifications Port Type 2.3 Network Switched Ports2.3.1 10/100TX Ports Port NumberWorking Connectors 2.3.2 100FX Modules100FX Module Installation JP1 settingPart Number 2.3.3 Gigabit Ports and Modules Specifications 2.4 Rack Mounting Giga Port Module Installation stepsState 2.5 LED IndicatorsLED Name Interpretation2.6 Cooling Fans 2.7 Management Setup 2.7.1 Setup for Out-of-bandConsole Management Main Menu >Switch Static Configuration 2.7.2 Setup for In-bandManagement2.7.3 Quick Guide to Configure Switch IP Address >Administration Configuration >IP Configuration3. Console and Telnet Operation Power-on Self-testConsole messageCold Start Telnet Management Login PromptDirect Console Management >telnetStatus and Counters Reboot Switch 3.1 Main MenuProtocol Related Configuration TFTP Update Firmware LogoutAction menu Port Configuration 3.2 Switch Static ConfigurationManaged 24+2G Switch: Switch Configuration Trunk Configuration VLAN Configuration3.2.1 Port Configuration Managed 24+2G Switch: Port ConfigurationOptions - On=Enable, Off=Disable Options - Yes=Enable, No=DisableAuto : Port auto negotiation mode control setting Options - On=Enable, Off=DisableDISABLE The group is disabled STATIC Normal trunk Managed 24+2G Switch: VLAN Configuration 3.3.3 VLAN Configuration3.3.3.1 VLAN Configure VLAN ConfigurePer port control settings PVID : Port VID 3.3.3.2 Create a VLAN Group Create a Port-basedVLAN groupCreate an 802.1Q VLAN 3.3.3.3 Edit / Delete a VLAN Group Example to edit Vlan2 group 3.3.3.4 Groups Sorted ModeManaged 24+2G Switch: Group Sorted Selection Group Sorted : Sorted_by_NameManaged 24+2G Switch: Misc Configuration 3.3.4 Misc Configuration3.3.4.1 MAC Age Interval Max bridge transmit delay bound Port Security3.3.4.2 Broadcast Storm Filtering 3.3.4.3 Max Bridge Transmit Delay Bound 3.3.4.4 Port Security 3.3.4.5 Collision Retry Forever 3.3.4.6 Hash AlgorithmManaged 24+2G Switch: Device Configuration 3.3.5 Administration Configuration3.3.5.1 Change Username Change Password Device InformationManaged 24+2G Switch: Password Configuration 3.3.5.2 Change Password3.3.5.3 Device Information Managed 24+2G Switch: Device Configuration3.3.5.4 IP Configuration 3.3.6 Port Sniffer Configuration 3.3.7 Priority Configuration 3.3.7.1 Static Priority 3.3.7.2 802.1p Priority All High before Low = high priority packets firstManaged 24+2G Switch: MAC Address Configuration 3.3.8 MAC Address Configuration3.3.8.1 Static MAC Address Filtering MAC Address Previous MenuAdd static MAC address Select one static MAC address to edit or delete3.3.8.2 Filtering MAC Address Managed 24+2G Switch : Spanning Tree Protocol 3.4 Protocol Related Configuration3.4.1 STP STP EnableSTP Enable System ConfigurationPerport Configuration 3.4.2 SNMP 3.4.2.1 System Options3.4.2.2 Community Strings Add/Edit a Community String3.4.2.3 Trap Managers Add/Edit a trap managerManaged 24+2G Switch: GVRP Configuration 3.4.3 GVRP3.4.4 IGMP GVRP : Enabled3.4.5.1 Working Port Setting 3.4.5 LACP3.4.5.2 State Activity 3.4.5.3 LACP Status 3.4.6Managed 24+2G Switch: 802.1x System Configuration 3.4.6.1 Enable 802.1X Protocol3.4.6.2 802.1X System Configuration action-><Edit> <Save> <Quit>Force Unauth= Fu, Force Au=Fa, Auto=Au, None=No 3.4.6.3 802.1X Per Port ConfigurationManaged 24+2G Switch: 802.1x Port Status Port Status3.4.6.4 802.1X Misc. Configuration 3.5 Status and Counters 3.5.1 Port Status 3.5.2 Port Counters 3.5.3 System Information 3.6 Reboot Switch 3.6.2 Default3.6.1 Restart 3.7 TFTP Update Firmware 3.7.1 TFTP Update Firmware Main Menu >Reboot Switch >Restart3.7.2 TFTP Restore Configuration Main Menu >Reboot Switch >Default3.7.3 TFTP Backup Configuration 4. SNMP Management Set/Get 4.2 SNMP MIB-2and Private MIBPort MIB-2Objects Value OptionsPrivate MIB Objects Set/GetValue Options RFC1157 4.3 SNMP TrapsTrap Name Event of Trap GeneratedWeb Browser 5. Web ManagementBest Display Resolution 1024 x 768 pixels up Set IP Address for the device unit5.1 Start Browser Software and Making Connection Factory default IP address :_ Configuration Backup _ Reset System _ Reboot 5.2 Web Management Home Overview_ Administrator _ Stacking _ TFTP Update Firmware _ Menu _ Port Status _ Port Statistics5.3 Port status Config / AtualAtual : current flow control status 5.4 Port Statistics _ VLAN configuration _ Spanning tree 5.5 Administrator_ Switch settings _ Security Manager _ Stack Settings5.5.1 IP Address 5.5.2 Switch Setting 5.5.2.1 Basic Information5.5.2.2 Module Info 5.5.2.3 Advanced Default : use default values for all settings Enable : retry forever for collision situationApply : confirm and apply the settings CRC-Hash :use CRC-hashmethod5.5.3 Console Port Information Parity Check : none Stop Bits :Flow control : none 5.5.4 Port Controls Half = Half duplex 5.5.5 Trunking 5.5.5.1 Aggregator settings 5.5.5.2 Aggregator Information No active group configuredThe following pages illustrate three examples Two Static Trunking groups are configured Page 5.5.5.3 State Activity Per port LACP modeClick Button Apply : Apply the changes Control setting 5.5.6.2 Static MAC Address 5.5.6.3 MAC Address Filtering 5.5.7 VLAN configuration Port Based VLANEdit : to edit an existing VLAN group 5.5.7.1 Port-basedVLANClick Add : to create a new VLAN group Delete : to delete a VLAN groupVLAN name : Name of the VLAN group Group ID : Unique ID for the groupClick Apply to confirm the changes 5.5.7.2 802.1Q VLAN Add a new VLAN Remove - remove a member port Tag : outgoing frames with VLAN-TaggedUntag : outgoing frames without VLAN-Tagged Ingress Filtering Rule 2 : Drop Untagged Frame 5.5.8 Spanning Tree This page shows an example of STP port status messages. Valid values : 1 ~ STP parameters settingsSTP State : Enable or disable STP function Refer to Chapter 1 for STP Parameter DescriptionsSTP port parameters settings STP port status5.5.9 Port Sniffer 5.5.10 SNMP SNMP ParametersSNMP Managers SNMP Trap Managers 5.5.11 Security Manager Assign/Change password : Type the new password5.5.12 802.1X Configuration System Configuration 5.5.12.1 802.1X PerPort Configuration 5.5.12.2 802.1X Misc Configuration 5.5.13 Stack Settings Password- The password of the member unit Configure other members in the stackUsername - The login username of the member unit Stack Name - Give a name to this stack5.6 Stacking Stop Auto Refresh : Disable auto refresh Close Stack View window to exit stack management5.7 TFTP Update Firmware 1.Start your TFTP server5.Click Apply to start the download operation 7. Reboot the system 5.8 Configuration Backup 5.8.1 TFTP Restore Configuration5.8.2 TFTP Backup Configuration 5.9 Reset System Click Reset to start the operation5.10 Reboot Click Reboot to start operationCases to update firmware from console 6. Update Firmware from Console4.Enter Transfer ->Send File command Setup 1K Xmodem on Hyper TerminalAppendix A: Factory Default Settings Forward Delay Time 802.1X Function Settings