Cold Start, Power-on Self-test Console message | Xerox NS-2260

3. Console and Telnet Operation

This chapter describes the detailed console operation. It can be applied to either out-of-band console management or in-band Telnet management. Refer to Chapter 2 for installation details.

Cold Start

When the power to the switch is turned on, the device start initialization and self-test process. The self -test messages are displayed as follows if a console connection is established successfully.:

Power-on Self-test Console message

---------------------------------------------

$$$ Switch LOADER Checksum O.K !!!

$$$ Press any key to start Xmodem receiver:

$$$ Switch IMAGE Checksum			O.K !!!
$$$ Loading IMAGE
$$$ Switch Power On Self Test...
$$$ CPU(arm7) Sdram Test Start..
++	Memory Test (Long)	....	O.K !!!
++	Memory Test (Short) ...		O.K !!!
++	Memory Test (Byte)	....	O.K !!!
$$$ CPU(arm7) Sdram Test O.K !!!
$$$ Switch Register R/W Test ...			O.K !!!
$$$ Phy Register R/W Test ...			O.K !!!
$$$ Embedded Sram Built In Self Test ...				O.K !!!
$$$ Switch Data Area Checksum			...O.K !!!
$$$ Detect Module Card...		O.K !!!
$$$ Switch Engine Initialize...			O.K !!!
$$$ Trunk Initialize...		O.K !!!
$$$ Port Initialize...		O.K !!!
$$$ BwCtrl Initialize...		O.K !!!
$$$ Forwarding Initialize...O.K !!!
$$$ Vlan Initialize...		O.K !!!
---------------------------------------------

Both console management and Telnet management are same in operation starting from login prompt.

Image 37

Xerox NS-2260 operation manual Cold Start, Power-on Self-test Console message

Contents

NS-2260 Optional 100FX Modules Optional Gigabit Modules Trademarks Installation and Management Table of ContentsConsole and Telnet Operation Snmp Management Appendix a Factory Default Settings Update Firmware from Console Introduction Introduction Supports Ethernet frame length up to 1522 bytes Features Gvrp Hardware Specifications Speed status Software Specifications Management Objects Console TelnetWeb Management Objects Type Trap Event Trap Events Lacp enabled Lacp disabledRules of trunking IP Multicast address IP Multicast Function Igmp Multicast Forwarding Igmp SnoopingMAC Address Filtering Function Port Security Static MAC Address Port-based Vlan Vlan Function Protocol-based Vlan Ieee 802.1Q Vlan Tag-based VlanSpanning Tree Protocol STP related parameters Per port control settingsSpanning tree port states Port Sniffer FunctionPage QoS Priority Function Outgoing Service PolicyPriority Classification Methods 10 802.1X Port-Based Network Access Control Per-port 802.1X mode setting Enable 802.1X protocol Radius client configurationMisc. configuration Panel Description AC Power Supply Installation and Management Port Number Label Specifications Port Type Network Switched Ports1 10/100TX Ports Speed Compliance Cables Distance 2 100FX Modules JP1 setting Specifications Part Number Connector CableInstallation steps Cable Distance Gigabit Ports and Modules Part Number Wavelength Specifications Part Number Compliance Speed Duplex Rack Mounting Giga Port Module Installation steps LED Name State Interpretation System LEDs LED Indicators Cooling Fans Management Setup Setup for Out-of-band Console Management Quick Guide to Configure Switch IP Address Setup for In-band Management Cold Start Power-on Self-test Console message Direct Console Management Login PromptTelnet Management Main Menu When login successfully, the main menu is shown as follows Edit Action menu QuitSave Previous Switch Static Configuration menu is shown as follows Switch Static Configuration Managed 24+2G Switch Port Configuration Port ConfigurationPage Managed 24+2G Switch Trunk Configuration Trunk Configuration Trunk configuration example Vlan Configure Vlan Configuration Vlan Mode 802.1Q Create a Port-based Vlan group Create a Vlan Group PORT4 PORT5 PORT6 PORT7 PORT8 Create an 802.1Q Vlan Example to select one Vlan group for editing or deleting Edit / Delete a Vlan Group Example to edit Vlan2 group Groups Sorted Mode MAC Age Interval Misc Configuration Broadcast Storm Filtering Max Bridge Transmit Delay Bound Managed 24+2G Switch Port Security Hash Algorithm Collision Retry Forever Change Username Administration Configuration Device Information Change Password IP Configuration Port Sniffer Configuration Priority Configuration Static Priority 7.2 802.1p Priority High/Low Queue Service Ratio = Hx Lx, where x = 1~7 MAC Address Configuration Select one static MAC address to edit or delete Add static MAC address Example to enter a new filter address Filtering MAC Address 1 STP Protocol Related Configuration System Configuration STP Enable Perport Configuration System Options Snmp Add/Edit a Community String Community Strings Add/Edit a trap manager Trap Managers Igmp Gvrp Lacp Working Port Setting State Activity This page shows Lacp status of each trunk group Lacp Status 6.2 802.1X System Configuration Enable 802.1X Protocol 6.3 802.1X Per Port Configuration Managed 24+2G Switch 802.1x Misc Configuration 6.4 802.1X Misc. Configuration Status and Counters Port Status Port Counters Managed 24+2G Switch Port Counters System Information Default Reboot SwitchRestart Tftp Update Firmware Main Menu Reboot Switch Restart Tftp Restore Configuration Tftp Backup Configuration Snmp Management Snmp MIB-2 and Private MIB Configuring Snmp Settings via Console OperationPort MIB-2 Objects Set/Get Value Options Private MIB Objects Set/Get Value Options Trap Name RFC1157 Event of Trap Generated Snmp Traps Web Browser Best Display Resolution 1024 x 768 pixels upSet IP Address for the device unit Start Browser Software and Making Connection Web Management Home Overview Config / Atual Page Port Statistics Administrator IP Address Basic Information Switch Setting Module Info Advanced Page Parity Check none Stop Bits Flow control none Console Port Information Port Controls Page Trunking Aggregator settings Aggregator Information Two Static Trunking groups are configured Page State Activity Forwarding and Filtering Database 5.5.6.1 Igmp Snooping Static MAC Address MAC Address Filtering Port Based Vlan Port-based Vlan Page 7.2 802.1Q Vlan Add a new Vlan Page Ingress Filtering Rule 2 Drop Untagged Frame Spanning Tree Page Page Page Port Sniffer Snmp Parameters Snmp Managers Snmp Trap Managers Security Manager Assign/Change password Type the new password 12 802.1X Configuration System Configuration 12.1 802.1X PerPort Configuration 12.2 802.1X Misc Configuration Stack Settings Page Stacking Page Tftp Update Firmware Page Configuration Backup Tftp Restore Configuration Tftp Backup Configuration Reset System Reboot Setup 1K Xmodem on Hyper Terminal Cases to update firmware from console Appendix a Factory Default Settings Not available NASL2SWITCH