Sheave fixed block | Yamaha 5TE-F8197-10, LIT-11616-16-02 specs

SPECIAL TOOLS

GEN INFO

Tool No.	Tool name/How to use	Illustration

	Sheave fixed block
90890-04135	This tool is needed when removing or
YM-04135	This tool is needed when removing or
YM-04135	installing the secondary sheave
	installing the secondary sheave
	spring.

	Flywheel puller
90890-01404
YM-01404	These tools are needed to remove
	These tools are needed to remove
	the rotor.

	Damper rod holder (30 mm)
90890-01327	This tool is needed to loosen and
YM-01327	This tool is needed to loosen and
YM-01327	tighten the steering stem bearing
	tighten the steering stem bearing
	retainers.

	Oil filter wrench
90890-01426
YU-38411	This tool is needed to loosen or
	This tool is needed to loosen or
	tighten the oil filter cartridge.

	Ring nut wrench
90890-01430	This tool is needed to removing and
YM-38404	This tool is needed to removing and
YM-38404	installing the middle driven shaft
	installing the middle driven shaft
	bearing retainers.

90890-01467	Gear lash measurement tool
90890-01467
YM-01467
90890-01475	This tool is used to measure the gear
YM-01475	This tool is used to measure the gear
	lash.

	Ball joint remover/installer set
90890-01474
YM-01474	This tool is used to remove and install
	This tool is used to remove and install
	the ball joints.

	Ball joint remover/installer attachment
	set
YM-01477
	This tool is used to remove and install
	the ball joints.

	Sheave holder
90890-01701	This tool is needed to hold the
YS-01880-A	This tool is needed to hold the
YS-01880-A	primary sheave when removing or
	primary sheave when removing or
	installing the sheave bolts.

1 - 7

Image 23

Yamaha 5TE-F8197-10, LIT-11616-16-02 service manual Sheave fixed block

Contents

YFM400FAR YFM400FAR Important Information Manual Organization Exploded Diagrams GEN Spec Info CHK ENG ADJ Table of Contents Contents Chapter General Information Fuel Tank IntroductionSeat and Side Panels Chapter Engine Page Chapter Cooling System Rear AXLE/FINAL Drive Gear and Drive Shaft Troubleshooting Chapter Chassis Front Arms and Front Shock Absorbers Chapter Electrical Starting FAILURE/HARD Starting Faulty Drive TrainFaulty Gear Shifting Faulty Clutch Performance Malfunction Faulty BrakeOverheating Poor Braking Effect Model Label Vehicle Identification Number GASKETS, OIL Seals and O-RINGS Preparation for Removal ProceduresReplacement Parts Circlips Lock WASHERS/PLATES and Cotter PinsBearings and OIL Seals Checking of Connections Tool No Tool name/How to use Illustration Crankshaft installer set Sheave fixed block Compression gauge Clutch holding tool General Specifications Maxxis MikuniDR8EA/NGK YTX14AH Engine Seat Width Margin Thickness Head Diameter Face Width 41.27 mm Spec Spec Spec Pressure feed Splashed scavenge Camshaft Crank Pin Standard Limit Cylinder head tightening sequence Tightening torques Neutral switch M10 Reverse switch Stator assembly Chassis DOT Tightening torques Spec Electrical 5ND/NIPPON Thermostat MS5F-561/JIDECO4BA/DENSO Conversion Table Metric Multiplier Imperial Lubrication Points and Lubricant Types Coolant Flow Diagrams Radiator Thermostat To coolant reservoir OIL Flow Diagrams Oil filter Oil pump Oil strainer Cable Routing Spec Spec Spec Spec Spec Spec Spec Spec Spec Introduction CHK ADJ Removing the seat and side panels Seat and Side Panels Bumper and front fender Front CARRIER, Front Bumper and Front FenderRemoving the front carrier, front CHK ADJ First disconnect the negative lead Rear Carrier and Rear FenderRemoving the rear carrier and rear Fender CHK ADJ Bumper and Front Fender Fuel TankRemoving the fuel tank Removing the footrest boards Adjusting the Valve Clearance Adjusting the Valve Clearance Locknut 20 Nm 2.0 m kg, 14 ft lb Adjustment stepsTappet adjusting tool YM-08035 Engine idling speed 1,450 ~ 1,550 r/min Adjusting the Idling Speed Throttle lever free play ~ 5 mm 0.12 ~ 0.20 Adjusting the Throttle Lever Free PlayTurning Idling speed becomes Higher Turning out Lower Adjustment steps First step Speed limiter length 12 mm 0.47 Adjusting the Speed LimiterSecond step Adjusting the Starter Cable Speed limiter length adjustment steps Starter plunger stroke distance 15 mm 0.59 Spark plug gap ~ 0.7 mm 0.024 ~ 0.028 Checking the Spark PlugStandard spark plug DR8EA/NGK Loctite Checking the Ignition TimingEngine speed 1,450 ~ 1,550 r/min Recoil starter bolt 10 Nm 1.0 m kg, 7.2 ft Ib Compression gauge YU-33223 Adapter YU-33223-3 Measuring the Compression Pressure Measuring the Compression Pressure Do not allow foreign material to enter the crankcase Recommended oil Follow the left chartChecking the Engine OIL Level Oil filter wrench YU-38411 Replacement stepsChanging the Engine OIL Oil filter cartridge 17 Nm 1.7 m kg, 12 ft lb Cautio N Oil gallery bolt Nm 0.7 m kg, 5.1 ft lb Cleaning the AIR Filter Cleaning the AIR Filter Cleaning steps Checking the Coolant Level Changing the Coolant 10 Nm 1.0 m kg, 7.2 ft lb CHK ADJ Belt width 30.7 mm 1.21 in Limit 27.6 mm 1.09 Checking the Coolant TemperatureChecking the V-BELT Replacing steps Cleaning the Spark Arrester Rear brake pedal free play 20 ~ 30 mm 0.8 ~ 1.2 Adjusting the Rear BrakeRear brake pedal free play 20 ~ 30 mm 0.80 ~ 1.18 Gap a ~ 1 mm 0.00 ~ 0.04 DOT Checking the Front Brake Fluid LevelRecommended brake fluid Checking the Rear Brake Shoes Checking the Front Brake PadsBrake pad wear limit a 1 mm 0.04 Checking the Brake Hoses Bleed screw Nm 0.6 m kg, 4.3 ft lb Bleeding the Hydraulic Brake SystemAir bleeding steps Adjustment steps Control cable Adjusting the Select Lever Control Cable and Shift ROD Select lever shift rod Adjusting the Rear Brake Light Switch Recommended oil SAE 80 API GL-4 Hypoid gear oil Direction a Brake light comes on Sooner Direction b LaterChecking the Final Gear OIL Level Changing the Final Gear OIL Changing the Differential Gear OIL Checking the Constant Velocity Joint Dust Boots Checking the Steering System Adjusting the TOE-IN Locknut rod end 40 Nm 4.0 m kg, 29 ft lb Toe-in = É È Checking the Tires Adjusting the Front Shock AbsorbersAdjusting the Rear Shock Absorber Maximum Loading Limit Tire CharacteristicsManufacturer Size Type Maxxis Cold tire Front Rear Checking and Lubricating the Cables Checking the Wheels Recommended lubricant Lithium soap base grease Lubricating the LEVERS, PEDAL, ETC Charging Method Checking the Battery Keep Batteries and Electrolyte OUT of Reach of Children Battery condition checking steps Example Open-circuit Charging timeOr higher No charging is Necessary YES Charging method using a variable voltage charger Charging method using a constant voltage charger Checking the Fuses Quantity Pocket tester YU-03112-CDescription Changing the Headlight Bulb Adjusting the Headlight Beams Changing the Headlight Bulb Exhaust pipe AIR DUCTS, Muffler and Exhaust PipeRemoving the air ducts, muffler ENG Coolant reservoir Select Lever Unit and Coolant ReservoirRemoving the select lever unit Removing the hoses and leads Hoses and Leads Tighten Them to full torque Install all of the bolts/nuts and thenSpecifications Engine Mounting Bolts ENG Installing the Engine Removing the cylinder head Cylinder Head Rotor holding tool YU-01235 Removing the Cylinder Head Checking the Camshaft Sprocket Checking the Tappet CoversChecking the Timing Chain Tensioner ENG Installing steps Installing the Cylinder Head Cap bolt timing chain tensioner 23 Nm 2.3 m kg, 17 ft lb Installation steps Tighten Camshaft sprocket bolt Valves and Valve Springs Removing the camshaft, rockerArms and valves Camshaft and Rocker Arms ENG Removing the Valves and Valve Springs Slide hammer set YU-01083-A Slide hammer bolt M6 WeightRemoving the Camshaft and Rocker Arms Checking the Rocker Arms and Camshaft Valve spring compressor YM-04019Checking the Camshaft Check Rocker arms Rocker arm shafts Damage/wear → Replace Checking the Valves and Valve Springs Runout limit 01 mm 0.0004 Lapping steps U T ION Installed length Spring tilt limit Inner 1.6 mm 0.06 in Outer Installing the Valves and Valve Springs Installing the Camshaft and Rocker Arms Piston Removing the cylinder and piston Checking the Timing Chain Guide Removing the PistonPiston pin puller set YU-01304 Do not use a hammer to drive the piston pin out 0016 Measurement steps 1st stepCylinder bore C 84.500 ~ 84.510 mm 3268 ~ 3.3272 05 mm Standard Limit Top 03 ~ 0.08 mm 13 mm Ring 3rd stepChecking the Piston Rings Side clearance ~ 0.7 mm Ring End gap Standard Limit~ 0.40 mm 65 mm Ring 2nd ~ 0.60 mm 95 mm Ring Installing the Piston Installing the Cylinder Magneto Removing the A.C. magnetoChapter ENG Starter Disassembling the recoil starterAssembling the Recoil Checking the A.C. Magneto Removing the A.C. MagnetoFlywheel puller YM-01404 Disassembling the Recoil Starter Bolts starter clutch 30 Nm 3.0 m kg, 22 ft lb Checking the Starter Clutch Assembling the Recoil Starter Checking the Starter PulleyChecking the Recoil Starter Sealant Quick Gasket ACC-11001-05-01 Yamaha bond No Installing the A.C. Magneto Use a rotor holding tool 2 to hold the starter pulley Sheaves Removing the primarySecondary sheaves Primary and Secondary For installation, reverse the removal Sheave Primary Sliding SheaveDisassembling the primary sliding Sheave Assembling the Secondary Secondary SheaveDisassembling the secondary Removing steps Removing the Primary Secondary SheavesSheave holder YS-01880-A Disassembling the Secondary Sheave Free length 121.4 mm 4.78 Limit 115.33 mm 4.54 Weight outside diameter 30 mm 1.18 Limit 29.5 mm 1.16Checking the Primary Sheave Checking the Secondary Sheave Assembling the Secondary Sheave Assembling the Primary Sheave Nut 90 Nm 9.0 m kg, 65 ft lb Installing the Primary and Secondary Sheaves Clutch Removing the clutch Disassembling the clutch housing Checking the Clutch Removing the ClutchClutch holding tool YM-91042 Installing the Clutch Install Dowel pins Gasket New Clutch housing assembly OIL Pump Drive Gear Starter MOTOR, Timing Chain and OIL FilterRemoving the starter motor, timing Chain and oil filter ENG Lever CrankcaseSeparating the crankcase Pump Crankcase BearingsRemoving the crankcase bearings Separation steps Removing the OIL Pump Drive GearRemoval steps Separating the Crankcase Checking the OIL Strainer and OIL Delivery Pipe Checking the Timing Chain and Guide Assembling the Crankcase Checking the CrankcaseChecking the Bearings Installing the Shift Lever Tightening steps Installing the OIL Pump Drive Gear Crankshaft and Balancer CRANKSHAFT/INSTALLINGRemoving the crankshaft and oil Pump Disassembling the oil pump OIL Pump Checking the OIL Pump Removing the CrankshaftCrankcase separating tool YU-01135-A Crank width 62.95 ~ 63.00 mm 2.4783 ~ 2.4803 Checking the Crankshaft Installing the Crankshaft and Balancer Removing the transmission ENG Checking the Transmission Checking the Shift ForksDo not attempt to straighten a bent guide bar Checking the Shift CAM Checking the Chain Checking the Secondary Shaft and Driven Sprocket Installing the Transmission Drive and Driven Gear Shims Middle Drive ShaftRemoving the middle drive shaft Removing the middle driven shaft Middle Driven Shaft ENG Removing the Middle Driven Shaft Removing the Middle Drive Shaft Bearing retainer wrench YM-04128 Universal joint holder YM-04062 Checking the Pinion Gears Ring nut wrench YM-38404 Middle drive pinion gear shim thickness a = c a b Selecting the Middle Drive and Driven Gear ShimsSelection steps Middle driven pinion gear shim Thickness = d e + f g Hundredths Round value 5, 6Middle drive pinion gear shim Thickness mm ENG Installing the Middle Driven Shaft Tighten the bearing retainer Pinion gear fix clamp YM-04129 Installing the Middle Drive ShaftMeasuring the Middle Gear Backlash Middle gear lash ~ 0.3 mm 0.004 ~ 0.012 Measurement steps Gear lash measurement tool YM-01467 Removing the radiator Cool Cool Radiator cap tester YU-24460-01 Adapter YU-33984 Checking the Radiator Installing the Radiator Removing the thermostat Checking the Thermostat Installing the Thermostat Removing the water pump Disassembling the water pump Checking the Water Pump Disassembling the Water Pump Assembling the Water Pump Max. impeller shaft tilt 0.15 mm 0.006 Cool Removing the carburetor Carburetor Disassembling the carburetor Carb Checking the Carburetor Disassembling the Carburetor Carb Assembling the Carburetor Float height F.H mm 0.51 Measurement and adjustment steps Fuel level gauge YM-01312-A Adjusting the Fuel Level Following noises may indicate a mechanical defect Driv Troubleshooting Driv YES Troubleshooting chart Velocity joints and differential gear Removing the front constant Driv Constant Velocity Joints Disassembling the constant velocityJoints Differential gear Driv Checking the Constant Velocity Joints Removing the Differential Gear AssemblyAlways use new boot bands Assembling the Front Constant Velocity Joints Molybdenum disulfide grease 40 g 1.4 oz per dust bootChecking the Differential Gear Assembling the Differential Gear Differential gear lash 10 ~ 0.50 mm 0.004 ~ 0.020 Gear lash measurement tool YM-01475 Ring gear shim left and right Thickness mm Adjusting differential gear lashReduce shim Increase shim Checking the Differential Gear Operation Rear Axle Gear assembly and drive shaftInstalling Removing the rear axle, final drive Disassembling the final drive gear Drive Roller Bearings Assembling the Final DriveGear Disassembling the Final Drive Gear Removing the Rear Axle Replacing the Final Drive Roller Bearings Hundredths Rounded value 5, 6 Positioning the Final Drive Pinion Gear and Ring GearFinal drive pinion gear shim selection Final drive pinion gear shim thickness a = a b Bearing thickness f 11.00 mm Ring gear shim thickness = c + d e + f Measure/select Ring gear thrust clearance C Ring gear stopper shim selection Ring gear thrust clearance ~ 0.2 mm 0.004 ~ 0.008Thrust washer selection steps Thrust washer Thickness mm Checking the Rear Axle Ring gear stopper clearance adjustmentShim Thickness mm Ring gear stopper clearance 0.30 ~ 0.60 mm 0.012 ~ 0.024 Checking the Final Drive Gear Checking the Drive Shaft Final gear lash ~ 0.2 mm 0.004 ~ 0.008 Measurement and Adjusting the Final Gear LashFinal gear lash measurement Ring gear shim Thickness mm 25 0.30 40 0.45 Thrust washer Final gear lash adjustment Lithium-soap-based grease Installing the Final Drive GearAssembling the Final Drive Gear Nuts Bolts Sealant Quick gasket ACC-11001-05-01 Yamaha bond No.1215 Hubs Front WheelsRemoving the front wheels Is no danger of it falling over Removing the rear wheels Rear Wheels Checking the Wheel Hubs Brake disc maximum deflection 15 mm 0.006 Installing the Wheel HubsInstalling the Wheels Checking the Brake Discs Install Nuts wheel Brake Pads Front Brake PadsRemoving the front brake pads Brake pad wear limit 1 mm 0.04 Replacing the Front Brake Pads Brake caliper bleed screw 6 Nm 0.6 m kg, 4.3 ft lb Brake Master Cylinder Front Brake Master CylinderRemoving the front brake master Cylinder Master cylinder Disassembling the front brake Assembling the Front Brake Master Cylinder Checking the Master Cylinder Installing the Front Brake Master Cylinder Chas Calipers Front Brake CaliperRemoving the front brake calipers Assembling the Front Brake Calipers Checking the Front Brake Calipers Recommended brake component Replacement schedule Brake padsDisassembling the Front Brake Calipers Assembling the Front Brake Calipers Installing the Front Brake Calipers Fill Brake reservoir Removing the rear brake lever Removing the rear brake pedal Removing the rear brake drum Chas Removing the Rear Brake Checking the Rear Brake Lithium-soap base grease Installing the Rear BrakeBrake shoe lining thickness limit 2.0 mm 0.08 Brake drum inside diameter limit maximum 161 mm 6.34 Bolt brake shoe plate 28 Nm 2.8 m kg, 20 ft lb Bolt camshaft lever Nm 0.9 m kg, 6.5 ft lb Chas Removing the handlebar Cylinder AssemblyBrake Switch Handlebar Checking the Handlebar Removing the Rear Brake SwitchInstalling the Handlebar Installing the Rear Brake Lever Installing the Master Cylinder Assembly Guide Steering StemRemoving the steering stem Bearing Retainer Checking the Steering Stem Installing the Bearing RetainerInstalling the Cable Guide Removing the Bearing Retainer Knuckles TIE Rods and Steering KnucklesRemoving the tie rods and steering Knuckles Chas Checking the Steering Knuckles Removing the Steering KnucklesChecking the TIE Rods Chas Eye protection is recommended when using striking tools Installing the TIE Rods Shock absorbers Removing the front arms and front Absorber Arms and Front Shock Checking the Front Arms Removing the Front Arms Replacement steps Checking the Front Shock Absorber Nut 30 Nm 3.0 m kg, 22 ft lb Installing the Front Arms and Front Shock AbsorberNut 45 Nm 4.5 m kg, 32 ft lb Swingarm Removing the rear shock absorber Swingarm Housing Checking the Rear Shock Absorber Removing the SwingarmNut swingarm 82 Nm 8.2 m kg, 59 ft lb Checking the Swingarm Checking the Rubber BootInstalling the Rubber Boot Nut 63 Nm 6.3 m kg, 45 ft lb Loctite Bolt Loctite Nut Installing the Rear Axle Housing Electrical Components Elec Example chart shows that Checking a SwitchChecking a Switch Shown in the Manual Elec + Checking the Switch Continuity Elec Checking the Condition of the Bulbs Types of Bulbs Pocket tester YU-03112-C Checking the Condition of the Bulb Sockets Circuit Diagram Standard spark plug TroubleshootingProcedure Open-circuit voltage Or more at 20 C 68 F Spark plug cap resistance 10 kΩ at 20 C 68 F Spark plug gapMinimum spark gap 6.0 mm 0.24 Primary coil resistance 18 ~ 0.28 Ω at 20 C 68 F Both Meet SpecificationCorrect OUT of Specification C0NTINUITY Main switch Refer to Checking the Switches Properly connect the ignition system Replace the CDI unit Correct Poor Connection System Electric Starting System Elec If the Starter Motor Fails to Operate Does not Turn Turns Incorrect Correct Motor Starter MotorRemoving the starter motor Disassembling the starter motor Mica undercut 0.7 mm 0.03 Checking the Starter MotorOutside diameter 28 mm 1.10 Wear limit 27 mm 1.06 Assembling the Starter Motor Brush length 12.5 mm 0.49 Wear limit 5 mm 0.20 Charging Continuity No Continuity If the Battery is not Charged Charging voltage Meets SpecificationOUT Specification OUT of Specification Headlight fuse If the Headlight AND/OR Taillight Fail to Come on Correct Incorrect Checking the Lighting System Tester + lead → Blue lead 1 Tester lead → Black lead Meets Specification No Continuity Tester + lead → Blue terminal 1 Tester lead → Black terminal Elec Elec Elec EB806010 Properly connect the signal system Checking the Signal System If the neutral indicator light fails to come on If the reverse indicator light fails to come on 235.4 F Test Coolant temperature Thermo switch Continuity StepLess than 120 ± 3 C 248 ± 5.4 F BAD Condition Good Condition Correct OUT of Specification Meets System Cooling If the FAN Motor does not Move Circuit breaker resistance Zero Ω at 20 C 68 F Meets Specification Does not Turn Good Less than 86 ± 3 C 186.8 ± 5.4 F176 ± 5.4 F Properly connect the cooling system System If the Gear Motor Fails to Operate Replace the on-command four-wheel drive switch Correct Poor Connection Electrical System Fuel System Poor Medium and HIGH-SPEED Performance Compression System Faulty Drive Train Engine Operates but Machine will not Move Hard ShiftingShift Lever does not Move Jumps OUT of Gear Poor Braking Effect Poor Speed PerformanceOverheating Bulb Burnt OUT MalfunctionUnstable Handling Headlight Dark YFM400FAR Wiring Diagram Shingai Iwata Shizuoka Japan