Main switch Refer to Checking the Switches | Yamaha LIT-11616-16-02

IGNITION SYSTEM

* C0NTINUITY

ELEC

–

+

8.Main switch

Refer to “CHECKING THE SWITCHES”.

CORRECT

9.Pickup coil resistance

●Disconnect the AC magneto coupler from the wire harness.

●Connect the pocket tester (Ω ⋅ 100) to the pickup coil terminals.

Tester (+) lead → White/Red terminal 1 Tester (–) lead → White/Green terminal 2

●Check the pickup coil for the specified resistance.

Pickup coil resistance:

459 ~ 561 Ω at 20 °C (68 °F) (White/Red – White/Green)

MEETS

SPECIFICATION

10.Charging/rotor rotation direction detection coil resistance

●Disconnect the AC magneto coupler from the wire harness.

●Connect the pocket tester (Ω ⋅ 100) to the charging/rotor rotation direction detection coil terminal.

Tester (+) lead → Red terminal 1 Tester (–) lead → White/Blue terminal 2

INCORRECT

Replace the main switch.

OUT OF SPECIFICATION

Replace the pickup coil/stator assembly.

●Check the charging/rotor rotation direction detection coil for the specified resistance.

Rotor rotation direction sensing coil resistance:

0.085 ~ 0.105 Ω at 20 °C (68 °F) (Red – White/Blue)

MEETS

SPECIFICATION

OUT OF SPECIFICATION

Replace the pickup coil/stator assembly.

*

9 - 13

Image 320

Yamaha LIT-11616-16-02, 5TE-F8197-10 service manual Main switch Refer to Checking the Switches

Contents

YFM400FAR YFM400FAR Important Information Exploded Diagrams Manual Organization GEN Spec Info CHK ENG ADJ Table of Contents Contents Chapter General Information Fuel Tank IntroductionSeat and Side Panels Chapter Engine Page Chapter Cooling System Troubleshooting Rear AXLE/FINAL Drive Gear and Drive Shaft Chapter Chassis Chapter Electrical Front Arms and Front Shock Absorbers Faulty Drive Train Faulty Gear ShiftingFaulty Clutch Performance Starting FAILURE/HARD Starting Faulty Brake OverheatingPoor Braking Effect Malfunction Vehicle Identification Number Model Label GASKETS, OIL Seals and O-RINGS Preparation for Removal ProceduresReplacement Parts Circlips Lock WASHERS/PLATES and Cotter PinsBearings and OIL Seals Checking of Connections Tool No Tool name/How to use Illustration Crankshaft installer set Sheave fixed block Compression gauge Clutch holding tool General Specifications Maxxis MikuniDR8EA/NGK YTX14AH Engine Seat Width Margin Thickness Head Diameter Face Width 41.27 mm Spec Spec Spec Pressure feed Splashed scavenge Camshaft Crank Pin Standard Limit Cylinder head tightening sequence Tightening torques Neutral switch M10 Reverse switch Stator assembly Chassis DOT Tightening torques Spec Electrical 5ND/NIPPON Thermostat MS5F-561/JIDECO4BA/DENSO Metric Multiplier Imperial Conversion Table Lubrication Points and Lubricant Types Coolant Flow Diagrams Radiator Thermostat To coolant reservoir OIL Flow Diagrams Oil filter Oil pump Oil strainer Cable Routing Spec Spec Spec Spec Spec Spec Spec Spec Spec Introduction CHK ADJ Seat and Side Panels Removing the seat and side panels Bumper and front fender Front CARRIER, Front Bumper and Front FenderRemoving the front carrier, front CHK ADJ Rear Carrier and Rear Fender Removing the rear carrier and rearFender First disconnect the negative lead CHK ADJ Bumper and Front Fender Fuel TankRemoving the fuel tank Removing the footrest boards Adjusting the Valve Clearance Adjusting the Valve Clearance Locknut 20 Nm 2.0 m kg, 14 ft lb Adjustment stepsTappet adjusting tool YM-08035 Adjusting the Idling Speed Engine idling speed 1,450 ~ 1,550 r/min Throttle lever free play ~ 5 mm 0.12 ~ 0.20 Adjusting the Throttle Lever Free PlayTurning Idling speed becomes Higher Turning out Lower Adjustment steps First step Speed limiter length 12 mm 0.47 Adjusting the Speed LimiterSecond step Speed limiter length adjustment steps Adjusting the Starter Cable Starter plunger stroke distance 15 mm 0.59 Spark plug gap ~ 0.7 mm 0.024 ~ 0.028 Checking the Spark PlugStandard spark plug DR8EA/NGK Checking the Ignition Timing Engine speed 1,450 ~ 1,550 r/minRecoil starter bolt 10 Nm 1.0 m kg, 7.2 ft Ib Loctite Measuring the Compression Pressure Compression gauge YU-33223 Adapter YU-33223-3 Measuring the Compression Pressure Do not allow foreign material to enter the crankcase Recommended oil Follow the left chartChecking the Engine OIL Level Oil filter wrench YU-38411 Replacement stepsChanging the Engine OIL Cautio N Oil filter cartridge 17 Nm 1.7 m kg, 12 ft lb Cleaning the AIR Filter Oil gallery bolt Nm 0.7 m kg, 5.1 ft lb Cleaning the AIR Filter Cleaning steps Checking the Coolant Level Changing the Coolant 10 Nm 1.0 m kg, 7.2 ft lb CHK ADJ Belt width 30.7 mm 1.21 in Limit 27.6 mm 1.09 Checking the Coolant TemperatureChecking the V-BELT Replacing steps Cleaning the Spark Arrester Rear brake pedal free play 20 ~ 30 mm 0.8 ~ 1.2 Adjusting the Rear BrakeRear brake pedal free play 20 ~ 30 mm 0.80 ~ 1.18 Gap a ~ 1 mm 0.00 ~ 0.04 DOT Checking the Front Brake Fluid LevelRecommended brake fluid Checking the Rear Brake Shoes Checking the Front Brake PadsBrake pad wear limit a 1 mm 0.04 Checking the Brake Hoses Bleed screw Nm 0.6 m kg, 4.3 ft lb Bleeding the Hydraulic Brake SystemAir bleeding steps Adjusting the Select Lever Control Cable and Shift ROD Adjustment steps Control cable Adjusting the Rear Brake Light Switch Select lever shift rod Recommended oil SAE 80 API GL-4 Hypoid gear oil Direction a Brake light comes on Sooner Direction b LaterChecking the Final Gear OIL Level Changing the Final Gear OIL Checking the Constant Velocity Joint Dust Boots Changing the Differential Gear OIL Adjusting the TOE-IN Checking the Steering System Toe-in = É È Locknut rod end 40 Nm 4.0 m kg, 29 ft lb Checking the Tires Adjusting the Front Shock AbsorbersAdjusting the Rear Shock Absorber Tire Characteristics Manufacturer Size TypeMaxxis Maximum Loading Limit Cold tire Front Rear Checking the Wheels Checking and Lubricating the Cables Lubricating the LEVERS, PEDAL, ETC Recommended lubricant Lithium soap base grease Checking the Battery Charging Method Battery condition checking steps Keep Batteries and Electrolyte OUT of Reach of Children Example Open-circuit Charging timeOr higher No charging is Necessary Charging method using a variable voltage charger YES Charging method using a constant voltage charger Checking the Fuses Quantity Pocket tester YU-03112-CDescription Adjusting the Headlight Beams Changing the Headlight Bulb Changing the Headlight Bulb Exhaust pipe AIR DUCTS, Muffler and Exhaust PipeRemoving the air ducts, muffler ENG Coolant reservoir Select Lever Unit and Coolant ReservoirRemoving the select lever unit Hoses and Leads Removing the hoses and leads Install all of the bolts/nuts and then SpecificationsEngine Mounting Bolts Tighten Them to full torque ENG Installing the Engine Removing the cylinder head Cylinder Head Removing the Cylinder Head Rotor holding tool YU-01235 Checking the Camshaft Sprocket Checking the Tappet CoversChecking the Timing Chain Tensioner ENG Installing the Cylinder Head Installing steps Installation steps Cap bolt timing chain tensioner 23 Nm 2.3 m kg, 17 ft lb Tighten Camshaft sprocket bolt Removing the camshaft, rocker Arms and valvesCamshaft and Rocker Arms Valves and Valve Springs ENG Removing the Valves and Valve Springs Slide hammer set YU-01083-A Slide hammer bolt M6 WeightRemoving the Camshaft and Rocker Arms Checking the Rocker Arms and Camshaft Valve spring compressor YM-04019Checking the Camshaft Check Rocker arms Rocker arm shafts Damage/wear → Replace Checking the Valves and Valve Springs Runout limit 01 mm 0.0004 U T ION Lapping steps Installed length Installing the Valves and Valve Springs Spring tilt limit Inner 1.6 mm 0.06 in Outer Installing the Camshaft and Rocker Arms Removing the cylinder and piston Piston Removing the Piston Piston pin puller set YU-01304Do not use a hammer to drive the piston pin out Checking the Timing Chain Guide Measurement steps 1st step Cylinder bore C 84.500 ~ 84.510 mm 3268 ~ 3.327205 mm 0016 3rd step Checking the Piston RingsSide clearance Standard Limit Top 03 ~ 0.08 mm 13 mm Ring End gap Standard Limit ~ 0.40 mm 65 mm Ring2nd ~ 0.60 mm 95 mm Ring ~ 0.7 mm Ring Installing the Piston Installing the Cylinder Magneto Removing the A.C. magnetoChapter ENG Starter Disassembling the recoil starterAssembling the Recoil Removing the A.C. Magneto Flywheel puller YM-01404Disassembling the Recoil Starter Checking the A.C. Magneto Checking the Starter Clutch Bolts starter clutch 30 Nm 3.0 m kg, 22 ft lb Assembling the Recoil Starter Checking the Starter PulleyChecking the Recoil Starter Installing the A.C. Magneto Sealant Quick Gasket ACC-11001-05-01 Yamaha bond No Use a rotor holding tool 2 to hold the starter pulley Removing the primary Secondary sheavesPrimary and Secondary Sheaves For installation, reverse the removal Primary Sliding Sheave Disassembling the primary slidingSheave Sheave Assembling the Secondary Secondary SheaveDisassembling the secondary Removing the Primary Secondary Sheaves Sheave holder YS-01880-ADisassembling the Secondary Sheave Removing steps Weight outside diameter 30 mm 1.18 Limit 29.5 mm 1.16 Checking the Primary SheaveChecking the Secondary Sheave Free length 121.4 mm 4.78 Limit 115.33 mm 4.54 Assembling the Primary Sheave Assembling the Secondary Sheave Nut 90 Nm 9.0 m kg, 65 ft lb Installing the Primary and Secondary Sheaves Removing the clutch Clutch Disassembling the clutch housing Checking the Clutch Removing the ClutchClutch holding tool YM-91042 Installing the Clutch Install Dowel pins Gasket New Clutch housing assembly Starter MOTOR, Timing Chain and OIL Filter Removing the starter motor, timingChain and oil filter OIL Pump Drive Gear ENG Lever CrankcaseSeparating the crankcase Pump Crankcase BearingsRemoving the crankcase bearings Removing the OIL Pump Drive Gear Removal stepsSeparating the Crankcase Separation steps Checking the Timing Chain and Guide Checking the OIL Strainer and OIL Delivery Pipe Assembling the Crankcase Checking the CrankcaseChecking the Bearings Installing the Shift Lever Installing the OIL Pump Drive Gear Tightening steps CRANKSHAFT/INSTALLING Removing the crankshaft and oilPump Crankshaft and Balancer OIL Pump Disassembling the oil pump Checking the OIL Pump Removing the CrankshaftCrankcase separating tool YU-01135-A Checking the Crankshaft Crank width 62.95 ~ 63.00 mm 2.4783 ~ 2.4803 Installing the Crankshaft and Balancer Removing the transmission ENG Checking the Shift Forks Do not attempt to straighten a bent guide barChecking the Shift CAM Checking the Transmission Checking the Secondary Shaft and Driven Sprocket Checking the Chain Installing the Transmission Drive and Driven Gear Shims Middle Drive ShaftRemoving the middle drive shaft Middle Driven Shaft Removing the middle driven shaft ENG Removing the Middle Drive Shaft Removing the Middle Driven Shaft Universal joint holder YM-04062 Bearing retainer wrench YM-04128 Ring nut wrench YM-38404 Checking the Pinion Gears Middle drive pinion gear shim thickness a = c a b Selecting the Middle Drive and Driven Gear ShimsSelection steps Middle driven pinion gear shim Thickness = d e + f g Hundredths Round value 5, 6Middle drive pinion gear shim Thickness mm ENG Installing the Middle Driven Shaft Tighten the bearing retainer Installing the Middle Drive Shaft Measuring the Middle Gear BacklashMiddle gear lash ~ 0.3 mm 0.004 ~ 0.012 Measurement steps Pinion gear fix clamp YM-04129 Gear lash measurement tool YM-01467 Cool Removing the radiator Cool Checking the Radiator Radiator cap tester YU-24460-01 Adapter YU-33984 Installing the Radiator Removing the thermostat Installing the Thermostat Checking the Thermostat Removing the water pump Disassembling the water pump Disassembling the Water Pump Checking the Water Pump Max. impeller shaft tilt 0.15 mm 0.006 Assembling the Water Pump Cool Removing the carburetor Disassembling the carburetor Carburetor Carb Disassembling the Carburetor Checking the Carburetor Carb Float height F.H mm 0.51 Measurement and adjustment steps Assembling the Carburetor Adjusting the Fuel Level Fuel level gauge YM-01312-A Driv Following noises may indicate a mechanical defect Troubleshooting Driv Troubleshooting chart YES Removing the front constant Velocity joints and differential gear Driv Constant Velocity Joints Disassembling the constant velocityJoints Differential gear Driv Checking the Constant Velocity Joints Removing the Differential Gear AssemblyAlways use new boot bands Assembling the Front Constant Velocity Joints Molybdenum disulfide grease 40 g 1.4 oz per dust bootChecking the Differential Gear Assembling the Differential Gear Gear lash measurement tool YM-01475 Differential gear lash 10 ~ 0.50 mm 0.004 ~ 0.020 Adjusting differential gear lash Reduce shimIncrease shim Ring gear shim left and right Thickness mm Checking the Differential Gear Operation Gear assembly and drive shaft InstallingRemoving the rear axle, final drive Rear Axle Disassembling the final drive gear Drive Roller Bearings Assembling the Final DriveGear Removing the Rear Axle Disassembling the Final Drive Gear Replacing the Final Drive Roller Bearings Positioning the Final Drive Pinion Gear and Ring Gear Final drive pinion gear shim selectionFinal drive pinion gear shim thickness a = a b Hundredths Rounded value 5, 6 Ring gear shim thickness = c + d e + f Bearing thickness f 11.00 mm Measure/select Ring gear thrust clearance C Ring gear thrust clearance ~ 0.2 mm 0.004 ~ 0.008 Thrust washer selection stepsThrust washer Thickness mm Ring gear stopper shim selection Ring gear stopper clearance adjustment Shim Thickness mmRing gear stopper clearance 0.30 ~ 0.60 mm 0.012 ~ 0.024 Checking the Rear Axle Checking the Drive Shaft Checking the Final Drive Gear Final gear lash ~ 0.2 mm 0.004 ~ 0.008 Measurement and Adjusting the Final Gear LashFinal gear lash measurement Final gear lash adjustment Ring gear shim Thickness mm 25 0.30 40 0.45 Thrust washer Lithium-soap-based grease Installing the Final Drive GearAssembling the Final Drive Gear Sealant Quick gasket ACC-11001-05-01 Yamaha bond No.1215 Nuts Bolts Front Wheels Removing the front wheelsIs no danger of it falling over Hubs Rear Wheels Removing the rear wheels Checking the Wheel Hubs Installing the Wheel Hubs Installing the WheelsChecking the Brake Discs Brake disc maximum deflection 15 mm 0.006 Install Nuts wheel Brake Pads Front Brake PadsRemoving the front brake pads Replacing the Front Brake Pads Brake pad wear limit 1 mm 0.04 Brake caliper bleed screw 6 Nm 0.6 m kg, 4.3 ft lb Front Brake Master Cylinder Removing the front brake masterCylinder Brake Master Cylinder Disassembling the front brake Master cylinder Checking the Master Cylinder Assembling the Front Brake Master Cylinder Installing the Front Brake Master Cylinder Chas Calipers Front Brake CaliperRemoving the front brake calipers Calipers Assembling the Front Brake Checking the Front Brake Calipers Recommended brake component Replacement schedule Brake padsDisassembling the Front Brake Calipers Installing the Front Brake Calipers Assembling the Front Brake Calipers Fill Brake reservoir Removing the rear brake lever Removing the rear brake pedal Removing the rear brake drum Chas Removing the Rear Brake Checking the Rear Brake Installing the Rear Brake Brake shoe lining thickness limit 2.0 mm 0.08Brake drum inside diameter limit maximum 161 mm 6.34 Lithium-soap base grease Bolt camshaft lever Nm 0.9 m kg, 6.5 ft lb Bolt brake shoe plate 28 Nm 2.8 m kg, 20 ft lb Chas Cylinder Assembly Brake SwitchHandlebar Removing the handlebar Removing the Rear Brake Switch Installing the HandlebarInstalling the Rear Brake Lever Checking the Handlebar Installing the Master Cylinder Assembly Guide Steering StemRemoving the steering stem Bearing Retainer Installing the Bearing Retainer Installing the Cable GuideRemoving the Bearing Retainer Checking the Steering Stem TIE Rods and Steering Knuckles Removing the tie rods and steeringKnuckles Knuckles Chas Checking the Steering Knuckles Removing the Steering KnucklesChecking the TIE Rods Chas Eye protection is recommended when using striking tools Installing the TIE Rods Removing the front arms and front Shock absorbers Arms and Front Shock Absorber Removing the Front Arms Checking the Front Arms Replacement steps Checking the Front Shock Absorber Nut 30 Nm 3.0 m kg, 22 ft lb Installing the Front Arms and Front Shock AbsorberNut 45 Nm 4.5 m kg, 32 ft lb Removing the rear shock absorber Swingarm Housing Swingarm Checking the Rear Shock Absorber Removing the SwingarmNut swingarm 82 Nm 8.2 m kg, 59 ft lb Checking the Swingarm Checking the Rubber BootInstalling the Rubber Boot Installing the Rear Axle Housing Nut 63 Nm 6.3 m kg, 45 ft lb Loctite Bolt Loctite Nut Electrical Components Elec Example chart shows that Checking a SwitchChecking a Switch Shown in the Manual Elec + Checking the Switch Continuity Elec Types of Bulbs Checking the Condition of the Bulbs Pocket tester YU-03112-C Checking the Condition of the Bulb Sockets Circuit Diagram Troubleshooting ProcedureOpen-circuit voltage Or more at 20 C 68 F Standard spark plug Spark plug cap resistance 10 kΩ at 20 C 68 F Spark plug gapMinimum spark gap 6.0 mm 0.24 Both Meet Specification Correct OUT of SpecificationC0NTINUITY Primary coil resistance 18 ~ 0.28 Ω at 20 C 68 F Main switch Refer to Checking the Switches Correct Poor Connection Properly connect the ignition system Replace the CDI unit System Electric Starting System Elec If the Starter Motor Fails to Operate Turns Does not Turn Incorrect Correct Starter Motor Removing the starter motorDisassembling the starter motor Motor Mica undercut 0.7 mm 0.03 Checking the Starter MotorOutside diameter 28 mm 1.10 Wear limit 27 mm 1.06 Brush length 12.5 mm 0.49 Wear limit 5 mm 0.20 Assembling the Starter Motor Charging If the Battery is not Charged Continuity No Continuity Meets Specification OUT SpecificationOUT of Specification Charging voltage Headlight fuse If the Headlight AND/OR Taillight Fail to Come on Correct Incorrect Checking the Lighting System Meets Specification No Continuity Tester + lead → Blue lead 1 Tester lead → Black lead Tester + lead → Blue terminal 1 Tester lead → Black terminal Elec Elec Elec EB806010 Properly connect the signal system Checking the Signal System If the neutral indicator light fails to come on If the reverse indicator light fails to come on 235.4 F Test Coolant temperature Thermo switch Continuity StepLess than 120 ± 3 C 248 ± 5.4 F Good Condition BAD Condition Correct OUT of Specification Meets Cooling System If the FAN Motor does not Move Meets Specification Does not Turn Circuit breaker resistance Zero Ω at 20 C 68 F Good Less than 86 ± 3 C 186.8 ± 5.4 F176 ± 5.4 F Properly connect the cooling system System If the Gear Motor Fails to Operate Replace the on-command four-wheel drive switch Correct Poor Connection Fuel System Electrical System Compression System Poor Medium and HIGH-SPEED Performance Faulty Drive Train Hard Shifting Shift Lever does not MoveJumps OUT of Gear Engine Operates but Machine will not Move Poor Braking Effect Poor Speed PerformanceOverheating Malfunction Unstable HandlingHeadlight Dark Bulb Burnt OUT YFM400FAR Wiring Diagram Shingai Iwata Shizuoka Japan