Configuration

 

89

 

 

 

 

 

 

 

 

 

 

 

 

 

Control Panel Parameters

 

 

 

 

 

 

 

Table 10 • Printer Parameters (Sheet 18 of 27)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parameter

 

Action/Explanation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Set Control Prefix Character

 

 

 

 

CONTROL PREFIX

 

 

 

 

 

 

The printer looks for this two-digit hex character to indicate the start of a

 

 

 

-

<

 

>7EH

+

ZPL/ZPL II control instruction. The “H” that is displayed indicates

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hexadecimal and is not part of the value.

 

 

 

 

 

 

 

 

Note • Do not use the same hex value for the control, format, and

 

 

 

 

 

 

 

 

delimiter character. The printer must see different characters to

 

 

 

 

 

 

 

 

work properly.

 

 

 

 

 

 

Default: 7E (tilde—displayed as a black square)

 

 

 

 

Range: 00 to FF

 

 

 

 

To change the value shown:

 

 

 

 

1. Press the left oval to move to the next digit position.

 

 

 

 

2. Press the right oval to increase the value of the digit.

 

 

 

 

 

 

 

 

 

Set Format Prefix Character

 

FORMAT PREFIX

 

 

 

The format prefix is a two-digit hex value used as a parameter place marker

 

-

<^>5EH

+

 

in ZPL/ZPL II format instructions. The “H” that is displayed indicates

 

 

 

 

 

 

 

 

Hexadecimal and is not part of the value. The printer looks for this hex

 

 

 

 

character to indicate the start of a ZPL/ZPL II format instruction. See the

 

 

 

 

ZPL II Programming Guide for more information.

 

 

 

 

Note • Do not use the same hex value for the control, format, and

 

 

 

 

delimiter character. The printer must see different characters to

 

 

 

 

work properly.

 

 

 

 

Default: 5E (caret)

 

 

 

 

Range: 00 to FF

 

 

 

 

To change the value shown:

 

 

 

 

1. Press the left oval to move to the next digit position.

 

 

 

 

2. Press the right oval to increase the value of the digit.

 

 

 

 

 

 

 

 

 

Set Delimiter Character

 

DELIMITER CHAR

 

 

 

The delimiter character is a two-digit hex value used as a parameter place

 

-

<,>2CH

+

 

marker in ZPL/ZPL II format instructions. See the ZPL II Programming

 

 

 

 

Guide for more information.

 

 

 

 

Note • Do not use the same hex value for the control, format, and

 

 

 

 

delimiter character. The printer must see different characters to

 

 

 

 

work properly.

 

 

 

 

Default: 2C (comma)

 

 

 

 

Range: 00 to FF

To change the value shown:

1.Press the left oval to move to the next digit position.

2.Press the right oval to increase the value of the digit.

9/6/07

XiIIIPlus/R110Xi/R170Xi User Guide

13383L-004 Rev. A