Oki 5050 manual Cation Cancel

Page 54

Yes ◀ key. After the report is printed, the display shows BEGIN SCANNING? If you want to make corrections, press the No ▶ key and go back to Step

9.To remove a location, select the location in the

same way, but press the No ▶ key to delete it from your transmission.

15When all of your selections are correct, press the Start key. Your OKIFAX scans the documents into memory and waits until the time and date you have set before sending the fax. When scanning is completed, your OKIFAX is available for other transmission operations.

Canceling a Delayed Transmission

1Press the Stop key. The display shows COMMUNI-

CATION CANCEL.

2Press the Yes ◀ key. The display shows the Loca- tion ID of the delayed transmission currently loaded in your OKIFAX.

3Press the Yes ◀ key.

4If the delayed transmission was a feeder transmis- sion, press the Stop key again to remove the document from the document feeder.

Sending a Fax to Multiple Locations (Broadcasting)

1Load your documents.

2Press the Select Function key.

42Faxing: Advanced Operations

3Press the 2/Broadcast ↔ Feeder TX One Touch key. The display shows BROADCAST/MEMORY TX.

4Select a location. Refer to the instructions below.

To Select Using

Do This

 

A One Touch key

Press the One Touch key. (On the

 

OKIFAX 5600, lift the main One Touch

 

keypad to access One Touch keys 16–30.)

An Auto Dial number

Press the Auto Dial key, then enter the

two-digit Auto Dial number on the

 

 

numeric keypad.

 

A group

Using the numeric keypad, press the #

key, then enter the number of the group

you want to use.

A number dialed on

Dial as you would on a normal telephone.

the numeric keypad

 

 

5Press the Yes ◀ key to confirm your selection.

6Repeat Steps 4 and 5 as often as necessary to continue selecting locations.

7When you are finished selecting locations, press the No ▶ key at the SELECT LOCATION(S) message.

8If you have selected multiple locations, your OKIFAX asks if you want to confirm your selections with a printed report before proceeding. If you do, press the Yes ◀ key. After the report is printed, the display shows BEGIN SCANNING? If you want to make corrections, press the No ▶ key and go back to Step 4. To remove a location, select the location in the same way, but press the No ▶ key to delete it from your transmission.

Of5050hw.pm6

42

4/15/98, 9:32 AM

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Okifax Okidata Federal Communications Commission Requirements for End Users FCC Telephone Consumer Protection Act OF5050M.PM6 15/98, 923 AM Industry Canada Radio Interference Statement Safety Toner Cartridge Image Drum Unit Handling Direct Access ManuallyContents Faxing Advanced Operations Index Introduction See page 75 for ordering information Component Identification What You Should ReceiveComponents Jack for connecting to an outside telephone line Control Panel Control Panel Keys and Indicators Introduction Introduction One Touch Keypad Signal Tones Installation Take out the image drum cartridge Replace the image drum cartridge Close the document table Okifax Connect Power Loading Paper 3CLOCK Adjustment Setting the Answering Mode 4SYSTEM Data PRG Setting the Language User LanguageConnecting to a PBX Copying To stop the copying process, press the Stop key # OQZ Faxing Dial Directories One Touch Parameters Chain Dialing Programming Groups Faxing Dial Directories Faxing Basic Operations Loading Documents Your documents are now ready for faxing or copying Shortcut Fax Number Programming Receiving Faxes Manually Receiving Faxes in Memory Power Failures and Memory Lift the handset and press the Hook V Request key Faxing Advanced Operations Select a location. Refer to the following instructions Cation Cancel Press the Start key. Your Okifax begins sending the fax 5MAIL Password PRG RX MSG Relay Password Remote List noEnter Waiting to be Polled Polling RX, Select Location Customizing Okifax Customizing Setup FAX Ring Call FAX Number NOW Function noDistinctive RING, SET Not used Changing Your User Function Settings Dial Parameter Settings 2DIAL Parameter Fax Reports Understanding ReportsPrinting Reports Broadcast Confirmation Report MCF Result codes indicate the results of communications Problem Solving Push the buttons on the side of the copy stacker until you Of5050hw.pm6 15/98, 935 AM Printing a Cleaning Lift the document table into an upright position 15/98, 941 AM Change Drum Soon Message Push in the cover release buttons on the side of the copy 0213 FAX No Paper FAX Replace Paper Replace Toner Cart Problem Solving Problem Solving Problem Solving Service and Support Limited Warranty Okidata Service Locations Specifications ITU-T G3Index Auto StartBusy Tone Detect Dial Prefix Incoming Ring ONE Touch Param Ring Response 51 Printer AlarmTimer Prog Redial TriesTSI/CSI Material Safety Data Sheet Appearance and odor Black granules, no odor Small Spills
Related manuals
Manual 2 pages 18.4 Kb
Top Page Image Contents