Teac W-860R owner manual Recording with Tape I and Tape ll, Erasing

Page 10

Recording

Recording with TAPE I and TAPE ll

Recording from a Stereo System

1.Press the POWER switch.

Select the source of the stereo system to record.

2.If you want to make a bi-directional recording, set the REV MODE switch to the Ë position.

ï… Set to the Ä position if

recording is to be made onË

ä

 

a single side of the tape.

3. Load a recordable cassette tape in TAPE I or II.

…If the safety tabs of the cassette tape have been broken off, block the holes with adhesive tape.

4.Select the desired DOLBY NR system.

5.Press the RECORD button.

The deck enters the record-pause mode. and π indicators light.

6.Adjust the recording level with the REC LEVEL control. The loudest sound should briefly reach around the "0 dB" point (for Normal or Chrome tapes) or the "+3 dB" point (for Metal tapes).

Normal/CrO2 Tape

Metal Tape

7. Press the PAUSE button to start recording.

…To stop recording temporarily, press the PAUSE button. To restart the tape, press the PAUSE button or play button.

…During the record-pause mode, if the button whose Ó/Á indicator is lit is pressed, recording will start. However, if the button whose Ó/Á indicator is not lit is pressed, only the tape direction will be changed; to restart the tape, press the button again.

…To stop recording, press the STOP button.

Erasing

Anything previously recorded on the tape will be automatically erased when you make a new recording on it. It can also be erased by "recording" on it with the REC LEVEL control set to "‹".

Record Muting Operation (TAPE I and TAPE Il)

Automatic spacing operation for 4-second blanks (during recording)

1.Press the REC MUTE button during recording.

The tape movement continues and a blank space of about 4 seconds is recorded (the RECORD indicator blinks). Then the deck enters the record-pause mode automatically (both the RECORD and PAUSE indicators light).

2.Press the PAUSE button to restart recording. The PAUSE indicator goes off.

…Automatic spacing operation for 4-second blanks (during record-pause)

In the record-pause mode, pressing the REC MUTE button will initiate the above record-muting operation automatically. The deck then returns to the record-pause mode.

…For a blank of more than 4 seconds

During recording, hold the REC MUTE button depressed for more than 4 seconds. A blank space will be made as long as the button is pressed. Release the button to enter the record- pause mode. To restart recording, press the PAUSE button.

…For a blank of less than 4 seconds

After pressing the REC MUTE button during recording, press the PAUSE button before 4 seconds has elapsed. The deck will stop and enter the record-pause mode. To restart recording, press the PAUSE button again.

Note:

During record muting operation (while the RECORD indicator is blinking), pressing the REC MUTE button again will release the record muting operation and recording will restart without stopping the tape.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 860R Important Safety Instructions Precautions Voltage Conversion General export models onlyRead This Before Operating Before UseConnection Tape HandlingBattery Installation Remote Control OperationMaintenance Cleaning Tape PathName of Each Control Fast Forward/CPS ButtonContinuous Playback PlaybackPlayback with Tape I or Tape Il Pitch Control Tape I onlyMulti-Counter Tape Counter ModeIntro Check Blank ScanCPS Computomatic Program Search How to Select any Required Tune Using CPSMulti-Counter Example Erasing RecordingRecording with Tape I and Tape ll Record Muting Operation Tape I and Tape IlContinuous Recording Tape I to Tape Il Parallel RecordingMIC/LINE Mixing Recording Dubbing Copying from Tape I to Tape ll Set the REV Mode switch to the desired positionDubbing Manual Editing with Pause Tape Il onlyTape I shorter than Tape Synchro Reverse DubbingTape Tape I longer than TapeTimer Recording Timer Controlled OperationConnection Troubleshooting SpecificationsLire ceci avant de faire fonctionner lappareil Avant utilisationRaccordements Manipulation des cassettesMise en place des piles Boîtier de télécommandeEntretien Nettoyage du chemin de bandeNom de chaque commande Touche de lecture avantRéglage de lacuité du son Platine I seulement LectureLecture avec la Platine I ou la Platine Il Lecture continueFonction de balayage des blancs Compteur de bandePresser la touche Intro Check Remarque CPS recherche informatisée de programmeRemarques sur la CPS Affichage du compteur ExempleEnregistrement avec la Platine I et Platine EnregistrementEffacement Enregistrement mixage MIC/LINE Enregistrement parallèleEnregistrement continu Platine I vers Platine Il Enregistrement mixage MIC/LINECopie Copie copie de la Platine I à la Platine IlCopie avec inversion synchronisée Appuyer sur une touche DUB Start High ou Normal RemarqueLecture par minuterie Utilisation dune minuterieEnregistrement par minuterie RaccordementsEn cas de difficulté SpécificationsBitte vor Inbetriebnahme lesen Vor InbetriebnahmeAnschlüsse KassettenHandhabungFernbedienung Pflege und WartungBezeichnungen der Bedienungselemente FunktionstastenVerwendung des Pitch Control Reglers Nur Deck WiedergabeWiedergabe mit Deck I order FolgewiedergabeLeerstellensprung Anspielfunktion Intro CheckBandzähler Die Intro CHECK-Taste betätigenHinweise zur CPS-Funktion Wahl eines Titels mit der CPS-FunktionZählwerkanzeige Löschen AufnahmeAufnahme mit Deck I und Deck Stummaufnahme Deck I/DeckMIC/LINE-Mischaufnahme ParallslaufnahmeKontinuierliche Aufnahme Deck I zu Deck Zum auslösen der Aufnahme die PAUSE-Taste erneut drückenManuelle Editierfunktion mit Pause nur Deck ÜberspielbetriebÜberspielbetrieb von Deck I auf Deck VorschtBand in Deck I kürzer als in Deck Überspielbetrieb mit Synchron BandumkehrBand in Deck I länger als in Deck Timergesteuerte Wiedergabe Timergesteueurter BetriebTimergesteuerte Aufnahme AnschlüsseStörungssuche Technische DatenUso delle audiocassette Prima dellusoCollegamenti Caricamento di una cassettaManutenzione Installazione batterieUso del telecomando Pulizia del percorso del nastroNome dei comandi Tasto di avanzamento rapidoComando Pitch Control solo Deck RiproduzioneRiproduzione per mezzo del deck I o del deck Il Riproduzione continuaContanastro Funzione di ricerca degli inizi Intro CheckPremere il tasto Intro Check Nota CPS ricerca computerizzata di braniScelta di un particolare brano con la funzione CPS Contanastro EsempioRegistrazione con deck I e deck CancellazioneRegistrazione PauseRegistrazione con missaggio MIC/LINE Registrazione parallelaRegistrazione continuata Registrazione con missaggio MIC/LINEMontaggio manuale con Pause solo deck Il DuplicazioneDuplicazione copia dal deck I al deck AvvertenzaDeck I più corto del Deck Duplicazione ad inversione sincronizzataDeck I più lungo del Deck Riproduzione via timer Uso del timerRegistrazione via timer CollegamentiPower DiagnosticaDati tecnici Manipulación de cintas Previo al empleoConexiones Carga de un cassetteInstalación de las pilas Operación de control remotoMantenimiento Limpieza de la trayectoria de la cintaDolby Timer Nombre de controlesUso de Pitch Control Tape I solamente ReproducciónReproducción con Tape I o Tape Reproducción continuaFunción de búsqueda de secciones sin grabar Contador de cintaPresione el botón Intro Check Natas sobre CPS ComputadoraCómo seleccionar la canción deseada utilizando CPS ContadorBorrado GrabaciónGrabación con Tape I y Tape Silenciamiento de grabaciónGrabación continua Tape I a Tape Grabación paralelaGrabación de mezcla MIC/LINE Edición manual con Pause Unicamente Tape Copia de cintasCopia de cintas de Tape I a Tape AtencionLa cinta de Tape I es de menor duración que la de Tape Copia con inversión sincronizadaPresione uno de los botones DUB Start High o Normal Nota La cinta de Tape I es de mayor duración que la de TapeReproducción programada Grabación y reproducción programadasGrabación programada ConexionesDetección de problemas EspecificacionesLees dit alvorens het toestel in gebruik te nemen Alvorens in gebruik te nemenAansluitingen Behandelen van cassettesReinigen van de onderdelen waarlangs de band Loopt Bediening op afstandOnderhoud Inleggen van de batterijenBenaming van de bedieningsorganen Gesynchroniseerde Toets BedienigstoetsenBandsnelheid Alleen Tape WeergaveWeergave met Tape I of Tape Doorlopende weergaveBIanko-aftastfunktie BandtellerDruk op de Intro Check toets Opmerking CPS fragmentzoeksysteem Computomatic Program SearchOpmerkingen aangaande het CPS fragmentzoeksysteem Bandteller VoorbeeldUitwissen OpnameOpname met Tape I en Tape Opnamedemping Tape I/TAPEDoorlopende opname Tape I naar Tape Gemengd opnemen van mikrofoon- en IijnsignalenParallelopname gelijktijdige opname op beide cassettes LevelHandbediend monteren met de Pause toets Alleen Tape DubbenDubben Kopiëren van Tape I of Tape LET OPTape I korter dan Tape Tape I langer dan TapeTimer-geregeld weergeven Timer-geregelde funktiesTimer-geregeld opnemen AansluitingenOplossen van moeilijlkheden Technische gegevensAnmerkungen zur Timer-gesteuerten Aufnahme Osservazioni riguardanti la registrazione con luso del timer
Top Page Image Contents