Kawasaki 80C152, 80C51 technical specifications Kawasaki LSI USA, Inc 102 Ver .9 KS152JB2

Page 102

KS152JB Universal Communications Controller Technical Specifications

GMOD.0 (PR) - Protocol - If set SDLC protocols with NRZI encoding, zero bit insertion, and SDLC ﬂags are used. If cleared, CSMA/CD link access with Manchester encoding is used.

GMOD.1,2 (PL0,1) - Preamble length

PL1 PL0 LENGTH (BITS)

0	0	0
0	1	8
1	0	32
1	1	64

The length includes the two bit Begin of Frame (BOF) ﬂag in CSMA/CD but does not include SDLC ﬂag. In SDLC mode, the BOF is an SDLC ﬂag, otherwise it is two consecutive ones. Zero length is not compatible in CSMA/CD mode.

GMOD.3 (CT) - CRC Type - If set, 32 bit AUTODIN-II-32 is used. If cleared, 16 bit CRC-CCITT is used.

GMOD.4 (AL) - Address Length - If set, 16 bit addressing is used. In 8 bit mode, a match with any of the 4 address registers will allow the frame to be accepted (ADR0, ADR1, ADR2, ADR3). “Don’t Care” bits may be masked in ADR0 and ADR1 with AMSK0 and AMSK1. In 16 bit mode, address are matched against “ADR1:ADR0” or “ADR3:ADR2”. Again don’t care bits in ADR1:ADR0 can be masked in AMSK1:AMSK0. A received address of all ones will be always be recognized in any mode.

GMOD.5,6 (M0,M1) - Mode select - Two test modes, an optional “alternate backoff” mode, or normal backoff can be enabled with these two bits.

M1 M0 Mode

0 0 Normal

01 Raw Transmit

10 Raw Receive

1 1 Alternate Backoff

GMOD.7 (XTCLK) - External Transmit Clock - If set an external 1X clock is used the transmitter. If cleared the internal baud rate generator provides the transmit clock. The input clock is applied to the P1.3 (TxC). The user software is responsible for setting or clearing this ﬂag. External receive clock is enabled by setting PCON.3

GO - DMA Go bit, see DCON0.

GRxD - GSC Receive Data input, an alternate function of one of the port 1 pins (PI.0). This pin is used as the receive input for the GSC. P1.0 must be programmed to a 1 for this function to oper- ate.

GSC - Global Serial Channel - A high level, multi-protocol, serial communication controller

Kawasaki LSI USA, Inc.

Page 102 of 120

Ver. 0.9 KS152JB2

Image 102

Contents Introduction Technical Specifications Name Description Port Pin DescriptionPIN Description Pin Name Alternate FunctionXTAL1 XTAL2RST Eben ALEPsen EpsenSpecial function Registers SFR map for the cpuReset Timing Reset Values of the SFRs Sbuf Indeterminate Tmod ConfigurationsScon PconPort 0 I/O Pad Port 2 I/O Pad Port bit I/O PadsPorts 4,5 Comments ProgramPsen Epsen Fetch viaTIMER/COUNTERS Tmod Timer/Counter Mode Control RegisterTcon Timer/Counter Control Register ModeTimer/Counter in Mode Timer/Counter 0 in Mode IE Interrupt Enable RegisterInterrupts Priority Level Structure Egste EDMA1 Egstv EDMA0 Egsre Egsrv Pgste PDMA1 Pgstv PDMA0 Pgsre PgsrvPgsrv PX0EX0 Egsrv 2BHPT1 PDMA1EDMA1 ET1 1BHKawasaki LSI USA, Inc Ver .9 KS152JB2 Power Down and Idle Status of the External Pins during Idle and Power DownALE Psen Pcon Power Control Register Smod IDLLocal Serial Channel Local Serial Port Mode ControllerSerial Port Mode Mode Load Sbuf Baud Rates Timer 1 generated commonly used Baud rates SmodMHZ SINGLE-STEP Operation JNBReti Kawasaki LSI USA Inc Global Serial Channel Introduction11/IDLE CRC None DC JAM CRCCsma Sdlc 11/IDLEExternal clock Internal clock Control cpu Control dma Raw Receive Raw Transmit CSMA/CD Overview CSMA/CD Frame FormatPreamble BOF Address Info CRC EOF Kawasaki LSI USA, Inc Ver .9 KS152JB2 23 24 Interframe Space Collision Detection CSMA/CD Data EncodingManchester Encoding BIT Time Jitter ToleranceNarrow Pulses Missing 0-to-1 TransitionUnexpected 1-to-0 Transition Response to a Detected Collision What the GSC was doing Resolution of CollisionsGSC Inactive TfifoBackoff DCRAlgorithm Random Backoff Prbs Tcdcnt Load Bkoff Slot Clock MyslotBKOFF= Myslot Deterministic Backoff Hardware Based Acknowledge Kawasaki LSI USA, Inc Ver .9 KS152JB2 Sdlc Frame Format BOF Address Control Info CRC EOFKawasaki LSI USA, Inc Ver .9 KS152JB2 Data Encoding Nrzi BIT TimeBIT STUFFING/STRIPPING Sending Abort Character Line IdleAcknowledgement Multi-Drop Network PRIMARY/SECONDARY StationsPoint-to-point Network Ring NetworkSdlc Hdlc Using a Preamble in SdlcHDLC/SDLC Comparison User Deﬁned ProtocolsLine Discipline Planning for Network Changes and ExpansionsDMA Servicing of GSC Channels Kawasaki LSI USA, Inc Ver .9 KS152JB2 Baud Rate Initialization Test Modes External Driver InterfaceJitter Receive BIT Time Received Local Value Manchester Encoding BIT TimeReceive Sampling Rate Received Transmit WaveformsReceiver Clock Recovery CSMA/CD Clock RecoveryRcbat Crce Determining Receiver ErrorsExternal Clocking AddressingDetermining Line Discipline 2 CPU/DMA Control of the GSCCollisions and Backoff What the GSC was doing Response GSC Register Descriptions Successful Ending of Transmissions and ReceptionsGMOD84H Xtclk PL1 PL0 PL1 PL0 Length BitsKawasaki LSI USA, Inc Ver .9 KS152JB2 DCJ DCR SA5 SA4 SA3 SA2 SA1 SA0 ARB REQ Garen Xrclk Gfien IDLRcabt Crce RDN Rfne Gren Haben Kawasaki LSI USA, Inc Ver .9 KS152JB2 LNI Noack Tcdt TDN Tfnf TEN DMA Kawasaki LSI USA, Inc Ver .9 KS152JB2 DMA Operation DMA with the 80C152DMA Registers DAS IDA Alternate Cycle ModeBurst Mode SAS ISASerial Port Demand Mode External Demand ModePCH P2 SFR DMA Cycle Resume Program Execution Timing Diagrams12 OSC.PERIODS ALE Psen P1 Inst Float DMA Transfer from Internal Memory to Internal Memory12 OSC. Periods ALE Psen Inst DMA Data OUT PCL Inst PCH DMA Cycle 12 OSC. Periods Resume Program Execution ALE PsenDMA Cycle Resume Program Execution Request Mode Arbiter ModeHold/Hold Acknowledge Using the HOLD/HLDA Acknowledge ARB REQALE ARB If Hlda = ALE AEQ ALE REQ Internal Logic of the ArbiterDmxrq Internal Logic of the Requester DMA Arbitration Kawasaki LSI USA, Inc.oup, Inc Ver .9 KS152JB2 Kawasaki LSI USA, Inc Ver .9 KS152JB2 Kawasaki LSI USA, Inc Ver .9 KS152JB2 DMA Arbitration with Hold/Hold Ack Summary of DMA Control Bits DAS IDA SAS ISA DoneInterrupt Structure IE0 TI+RI ET1 EX1 ET0 EX0PT1 PX1 PT0 PX0 IPN1GSC Transmitter Error Conditions Transmit Error Flags Logic for Clearing TEN, Setting TDNGSC Receiver Error Conditions Glossary Kawasaki LSI USA, Inc Ver .9 KS152JB2 DCON0/1 092H,093H Xtclk PL1 PL0 Kawasaki LSI USA, Inc 102 Ver .9 KS152JB2 Kawasaki LSI USA, Inc 103 Ver .9 KS152JB2 PT1 PX1 PT0 EX0 Myslot 0F5H DCJ DCR SA5 SA4 SA3 SA2 SA1 SA0 Smod ARB REQ Garen Xrclk Gfien IDL OVR Rcabt Crce RDN Rfne Gren Haben Kawasaki LSI USA, Inc 108 Ver .9 KS152JB2 SM0 SM1 SM2 REN TB8 RB8 TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0Gate Kawasaki LSI USA, Inc 111 Ver .9 KS152JB2 Data Pointer LOW PortStack Pointer DPL.7 DPL.6 DPL5 DPL.4 DPL.3 DPL.2 DPL.1 DPL.0DPH.7 DPH.6 DPH.5 DPH.4 DPH.3 DPH.2 DPH.1 DPH.0 Timer ControlData Pointer High DPHTimer 0 LSB Timer Mode ControlGate Timer Timer 1 LSBTimer 0 MSB Timer 1 MSBSerial Data Buffer Serial Port ControlSM0 SBUF.7Program Status Word RS1 RS0Accumulator ACC.7 ACC.6 ACC.5 ACC.4 ACC.3 ACC.2 ACC.1 ACC.0Kawasaki LSI USA, Inc 119 Ver .9 KS152JB2 Kawasaki LSI USA, Inc 120 Ver .9 KS152JB2