Spectrum Brands MI.61XX Allocate the Fifo software buffers, 2a Write first data for output boards

The setup order for the different synchronization options Synchronization (Option)

Setup synchronization for use with FIFO mode and equally clocked boards

Most of the steps are similar to the setup routine for standard synchronization mentioned before. In this passage only the differences between the two modes are shown. Please have a look at the passage before to see the complete setup procedure. The following steps differ from standard mode to FIFO mode. All steps that are not mentioned here are similar as described before.

(2) Allocate the FIFO software buffers

If you use the board in FIFO mode additional memory in the PC RAM is needed for software FIFO buffers. For details please refer to the according chapter for the FIFO mode.

Example of FIFO buffer allocation:

for (i = 0; i < FIFO_BUFFERS; i++) for (b = 0; b < 3; b++)

{

pnData[b][i] = (ptr16) GlobalAlloc (GMEM_FIXED, FIFO_BUFLEN); // allocate memory

SpcSetParam (b, SPC_FIFO_BUFADR0 + i, (int32) pnData[b][i]); // send the adress to the driver

}

(2a) Write first data for output boards

When using the synchronization FIFO mode with output boards this is the right position to fill the first software buffers with data. As you can read in the FIFO chapter, output boards need some data to be written to the software FIFO buffers before starting he board.

Example of calulcating and writing output data to software FIFO buffers:

// ----- data calculation routine -----	// some global		variables
int g_nPos =0;
void vCalcOutputData (ptr16 pnData, int32 lBufsize)	// function to		calculate the
{	// output	data. In		this case
int i;	// a sine	function		is used.

for (i = 0; i < (lBufsize/2); i++)

pnData[b][i] = (int16) (8191.0 * sin (2 * PI / 500000 * (g_nPos+i))); g_nPos += lBufsize/2;

}

// ----- main task -----
int main(int argc, char **argv)
{
...	// fill the first buffers with data
for (i =0; i < MAX_BUF; i++)
for (b = 0; b < 3; b++)	// for all installed boards
vCalcOutputData (pnData[b][i], BUFSIZE);
...
}

(5) Define the board for clock master

Using the synchronization option requires one board to be set up as the clock master for all the synchronized board. It is not allowed to set more than one board to clock master.

Register		Value	Direction	Description
SPC_COMMAND		0	r/w	Command register of the board
	SPC_SYNCMASTERFIFO	102	Defines the according board as the clock master for operating in FIFO mode only.
Example: board number 0 is clock master
SpcSetParam (hDrv[0], SPC_COMMAND,			SPC_SYNCMASTERFIFO);		// Set board 0 to clock master

(6) Define the remaining boards as clock slaves

It is necessary to set all the remaining boards to clock slaves to obtain correct internal driver settings.

Register		Value	Direction	Description
SPC_COMMAND		0	r/w	Command register of the board
	SPC_SYNCSLAVEFIFO	102	Defines the according board as a clock slave for operating in FIFO mode only.
Settings the remaining boards to clock slaves. Board number 0 is clock master in the example
SpcSetParam (hDrv[1], SPC_COMMAND,			SPC_SYNCSLAVEFIFO);		// Setting all the other boards to
SpcSetParam (hDrv[2], SPC_COMMAND,			SPC_SYNCSLAVEFIFO);		// clock slave is a must !

72 MI.61xx Manual