Spectrum Brands MI.61XX manual Starhub, Introduction Additional options

Page 9

Introduction	Additional options

Starhub

The star hub module allows the syn- chronisation of up to 16 MI boards. It is possible to synchronise boards of the same type with each other as well as different types.

The module acts as a star hub for clock and trigger signals. Each board is connected with a small ca- ble of the same length, even the ma- ster board. That minimises the clock skew between the different boards. The figure shows the piggyback mo- dule mounted on the base board schematically without any cables to achieve a better visibility.

Any board could be the clock ma- ster and the same or any other

board could be the trigger master. All trigger modes that are available on the master board are also available if the synchronisation star hub is used.

The cable connection of the boards is automatically recognised and checked by the driver at load time. So no care must be taken on how to cable the boards. The programming of the star hub is included in the standard board interface and consists of only 3 additional commands.

It is not possible to use this option together with the timestamp or extra I/O option, because the is just space for one piggyback module on the on-board expansion slot.

(c) Spectrum GmbH

9

Image 9

Contents English version October 5 MI.61xxPage Software Driver Installation Hardware InstallationIntroduction SoftwareProgramming the Board Fifo ModeAnalog Outputs Standard generation modesOption Extra I/O Option Gated ReplaySynchronization Option AppendixPreface IntroductionGeneral Information PrefaceDifferent models of the MI.61xx series MI.6110 MI.6111Introduction Additional options Extra I/O Option -XMFExtra I/O Option -XIO Introduction Additional options StarhubSpectrum type plate Hardware information Block diagram Technical DataOrder information Dynamic ParametersHardware informationIntroduction FilterHardware Installation Installing the board in the systemSystem Requirements Installing a board with extra I/O Option -XMF Installing a board with digital inputs/outputsMounting the wired boards Installing multiple boards synchronized by starhubHooking up the boards Only use the included flat ribbon cablesInstalling multiple synchronized boards Software Driver Installation Software Driver InstallationInterrupt Sharing Installation WindowsVersion control Driver Update Windows Software Driver Installation Windows Windows XP Windows XP Adding boards to the Windows NT driver Windows NTOverview LinuxNow it is possible to access the board using this device Installing the deviceDriver info Automatic load of the driverSoftware Overview SoftwareFirst Test with SBench SoftwareHeader files ++ Driver InterfaceMicrosoft Visual C++ Linux Gnu CNational Instruments LabWindows/CVI Other Windows C/C++ compilersDriver functions Include DriversFunction SpcSetParam Function SpcSetParamFunction SpcSetData Windows Function SpcGetDataSpectrum GmbH Type definition Delphi Pascal Programming InterfaceInclude Driver ExamplesDelphi Pascal Programming Interface Visual Basic Programming Interface Visual Basic ExamplesVBA for Excel Examples Visual Basic Programming Interface Programming the Board Error handlingOverview Register tablesInitialization Example for error checkingStarting the automatic initialization routine PCI RegisterHardware version Installed memoryDate of production Serial numberUsed interrupt line Installed features and optionsUsed type of driver Driver versionExample program for the board initialization Powerdown and resetSpcpcimemsize SpcpciserialnoChannel Selection Analog OutputsImportant note on channels selection Disabling the outputsOutput Amplifiers Setting up the outputsOutput offset Register Value Direction Description Amplitude rangeFilter Specifications Maximum Output RangeOutput Filters Standard generation modes General descriptionProgramming Maximum memsize Standard generation modes ProgrammingMaximum posttrigger in MSamples Minimum and stepsize of memsize and posttrigger in samplesStarting with interrupt driven mode Starting without interrupt classic modeCommand register ProgrammingStandard generation modesWriting data with SpcSetData Data organizationValue ’start’ as a 32 bit integer value Value ’len’ as a 32 bit integer valueStandard mode Bit Standard ModeSample format General Information Fifo ModeBackground Fifo Write Speed LimitationsSoftware Buffers Programming Fifo ModeTheoretical maximum sample rate PCI Bus Throughput 60040 Read out the number of available Fifo buffersBuffer processing Fifo Mode ProgrammingAnalog acquisition or generation boards Digital I/O 701x or 702x or pattern generator boards== Maxbuf Example Fifo generation modeSpcfifostart SpcfifowaitProgramming Clock generation Internally generated sample rateStandard internal sample rate Using plain quartz with no PLL External reference clockExternal clocking Direct external clock Minimum external sample rateMaximum external samplerate in MS/s External clock with divider ExampleCHANNEL0 CHANNEL1 CHANNEL2 CHANNEL3 Trigger modes and appendant registers Example for setting up the software triggerSoftware trigger External TTL triggerEdge triggers Example on how to set up the board for positive TTL triggerTrigger modes and appendant registers Positive TTL triggerPositive and negative TTL trigger Option Multiple Replay Standard ModeOutput modes Trigger modesTrigger modes Option Multiple Replay Resulting start delaysOption Gated Replay General information and trigger delayOption Gated Replay Value Direction DescriptionAllowed trigger modes Example programExternal TTL edge trigger Spctriggermode TmttlposDigital I/Os Option Extra I/OChannel direction Transfer DataAnalog Outputs Programming exampleAnalog Outputs Option Extra I/O Different synchronization options Synchronization OptionSynchronization with option cascading Synchronization with option starhubSet up the board parameters Setup order for the different synchronization optionsExample of board setup for three boards Write Data to on-board memory output boards onlyExample of board #2 set as trigger master Define the boards for trigger master3a Define synchronization or trigger Define the remaining boards as trigger slavesExample board number 0 is clock master Define the board for clock masterDefine the remaining boards as clock slaves Arm the boards for synchronizationWait for the end of the measurement Start all of the trigger master boardsRead data from the on-board memory acquisition boards only Example for data reading2a Write first data for output boards Allocate the Fifo software buffersSpcsyncmasterfifo SpcsyncslavefifoAs trigger slaves General information Additions for synchronizing different boardsCalculating the clock dividers 20xx 30xx 31xx 40xx 45xx 60xx 61xx 70xx 72xxBoard type 3122 3120 Setting up the clock divider40 MS/s Board type 3025 3131Delay in standard non Fifo modes Resulting delays using different boards or speedsDelay in Fifo mode Additions for equal boards with different sample ratesError name Value hex Value dec Error description Error CodesAppendix AppendixPin assignment of the multipin connector Extra I/O with external connectorOption -XMFPin assignment of the multipin cable Extra I/O with internal connector Option -XIO Pin assignment of the internal multipin connectorD14 D12 D10 D15 D13 D11