Sony PCM-R700 manual Erasing Sub Codes, 23EN, You can erase an ID even when it is not displayed

Erasing Sub Codes

You can erase any start ID or skip ID.

START ID ERASE

INPUT

ANALOG

DIGITAL

MODE

ANALOG INPUT

POWER

UNBALANCE

BALANCE

COUNTER RESET

¯ ON

¿ OFF

REC MODE

STANDARD

LONG

REMOTE

MARGIN RESET

WIRED OFF WIRELESS

48k

44.1k

OFF

SBM

ON

SHUTTLE

DATA

AMS

PREVIOUS

NEXT

REW

FF

REC MUTE

MENU

REC LEVEL

R

=

+

0

)

r

CH-1(L)

•

PHONE LEVEL

•

•

START ID

OPEN/CLOSE

STOP

PLAY

PAUSE

REC

•

AUTO

REHEARSAL

WRITE

ERASE

REPEAT

LOCATE

SET

•

•

•

6

p

(

P

r

0

10

MIN•

MAX

SKIP ID

CH-2(R)

•

PHONES

RENUMBER REHEARSAL

WRITE

ERASE

SKIP PLAY

MARK

•

•

0•

10

SKIP ID ERASE

Press either START ID ERASE or SKIP ID ERASE when the ID you want to erase appears in the display. “(ERASE)” appears in the display as the deck rewinds to the beginning of the ID, then “ID ERASE” appears as the deck erases the ID.

In the case of a skip ID, if “SKIP ID” has disappeared by the time you press SKIP ID ERASE, the deck will still erase the skip ID.

•It takes 9 seconds to erase a start ID.

•It takes 1 second to erase a skip ID.

•Program numbers are erased together with start IDs.

zYou can erase an ID even when it is not displayed

Just press the respective ERASE button. The tape is rewound, and the first ID detected is erased.

Note

A skip ID written at the same position of a start ID is erased when the start ID is erased.

Writing Sub Codes

Renumbering the Program

Numbers Automatically

(Renumbering Function)

The Renumbering function searches for each start ID from the beginning of the tape and assigns a new program number to each one starting with 1. Use the Renumbering function in the following cases:

•When you’ve added a start ID while playing the tape.

•When a program number is missing due to an erased start ID.

•When you began recording from the middle of the tape and wrote a program number that already exists, or when one of the start IDs has no program number.

INPUT

ANALOG

DIGITAL

MODE

ANALOG INPUT

POWER

UNBALANCE

BALANCE

COUNTER RESET

¯ ON

¿ OFF

REC MODE

STANDARD

LONG

REMOTE

MARGIN RESET

WIRED OFF WIRELESS

48k

44.1k

OFF

SBM

ON

SHUTTLE

DATA

AMS

PREVIOUS

NEXT

REW

FF

REC MUTE

MENU

REC LEVEL

R

=

+

0

)

r

CH-1(L)

•

PHONE LEVEL

•

•

START ID

OPEN/CLOSE

STOP

PLAY

PAUSE

REC

•

AUTO

REHEARSAL

WRITE

ERASE

REPEAT

LOCATE

SET

•

•

•

6

p

(

P

r

0

10

MIN•

MAX

SKIP ID

CH-2(R)

•

PHONES

RENUMBER REHEARSAL

WRITE

ERASE

SKIP PLAY

MARK

•

•

0•

10

RENUMBER

Press RENUMBER while the deck is stopped or playing.

“RENUMBER” flashes in the display and the tape is automatically rewound to its beginning. The deck then starts searching for each successive start ID writing a new program number for each one starting with 1. “RENUMBER” stops flashing and “ID WRITE” appears in the display for a few seconds as the deck begins rewriting the program numbers.

After renumbering is finished, the deck rewinds the tape automatically to its beginning, then stops.

zYou can specify any number as the starting number for the renumbering of programs.

For details, see “FIRST (PGM No.)” on page 25.

Note

The Renumbering function may not function correctly when:

•A blank section exists on the tape.

•The interval between two start IDs is less than 18 seconds (36 seconds in long-play mode).

•A start ID exists within 10 seconds from the end of the tape.

23EN

3-859-278-11(1)