Panasonic WV-CW864 Shutter Speed Shutter, Gain Control AGC, Synchronization Sync

Page 13

Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lens iris control in ALC mode.

(3) Shutter Speed (SHUTTER)

You can select a shutter speed from among 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, and 1/10 000 seconds.

See page 39 for the setting.

(4) Gain Control (AGC)

You can set the gain of an image to automatic adjustment [AGC ON (LOW, MID, HIGH)] or fixed (AGC OFF).

See page 39 for the setting.

(5) Electronic Sensitivity Enhancement (SENS UP)

The electronic sensitivity enhancement function varies the shutter speed to raise the sensitivity in low light conditions.

You can select the following shutter speeds for SENS UP.

1/30 seconds (x2), 1/15 seconds (x4), 1/10 seconds (x6), 1/6 seconds (x10), 1/3.8 seconds (x16), or 1/1.9 seconds (x32).

See page 39 for the setting.

There are two modes for SENS UP as follows:

AUTO: If you select x32, the sensitivity is raised automatically up to x32.

FIX: If you select x32, the sensitivity is raised to a fixed x32.

Notes:

•Moving objects will appear blurred when shot in electronic sensitivity enhancement mode since SENS UP is equivalent to reducing the shutter speed in a still picture camera.

•The horizontal and vertical resolution will be lowered in this mode.

•If the iris opening is too small, the SENS UP/AUTO mode will not function.

(6)Synchronization (SYNC)

You can select the internal sync (INT) mode or the line-lock sync (LL) mode. Additionally, this model accepts the VD2 signal from a specified component. Whenever the VD2 signal is supplied to this camera, the camera automatically switches to the VD2 sync mode.

When you select the line-lock (LL) mode, you can adjust vertical phase . See page 40 for the setting.

Important Notices:

The priority of sync modes is given as follows:

1.Multiplexed vertical drive (VD2) (highest)

2.Line-lock (LL)

3.Internal sync (INT) (lowest)

Note: The priority of the automatic sync modes is the same as shown above.

14

Image 13

Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesCamera Cleaning PrecautionsPreset Data Uploading or Downloading Do not attempt to disassemble the cam- eraNever aim the camera at the sun Do not install the camera in places sub- ject to vibrationsIf Over Heat appears on the monitor screen ConsumablesConstruction Setup Menu SetupUp Switch Right Switch Left Switch Focus Switch Zoom SwitchSET Key CAM SET Key Down Switch Close CAM Setup F4 key Key for 2 sec Key for 2 secoPresetting Setup Menu DescriptionAuto Mode Auto Mode Home Position Home PositionDigital Flip Digital Flip Auto Pan Key Auto PAN KEYLocal/Remote LOCAL/REMOTE Special 1 MenuCamera Gain Control AGC Shutter Speed ShutterElectronic Sensitivity Enhancement Sens UP Synchronization SyncRS485 communication Setup Menu Display Setting ProceduresMenu Display Submenu DisplayPreset Menu Display PresettingPosition Setting Position SET To Set Panning/Tilting PositionsPan Offset ZOOM/FOCUS setting menuTo Set the Lens Zoom and Focus Positions To Enter a New Preset ID Preset Identification Setting Preset IDTo Copy a Preset ID from Another Position To Change an Entered Preset IDTo Set a Display Position for a Preset ID Light Control Setting ALC/MANUALTo Return to the Preset Setting Menu Manual setting menuPreset Speed Setting Preset Speed Scene File Setting Scene FileTo Return to the Preset Number Set Menu To Return to the Setup MenuHome Position Setting Deleting Preset PositionsSelf Return Setting Self Return Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingSpecial 1 Menu Setting Special Local/Remote Setting LOCAL/REMOTEPrivacy Zone Privacy Zone Zone Scale setting menu Area Title Nesw setting menu When on Nesw is selectedProportional Pan/Tilt PROPO. P/T Area Title Area TitleDisplay Position setting menu Setting on UserDirection User setting menu Area Title EditingTo Quit Editing Patrol-learn and Patrol Play PatrolArea Title menu Patrol-learn with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyAlarm I/O submenu Alarm Input/Output Alarm IN/OUTCNT-CLS 1, 2 Output Password Verification Password Lock Password LockNew Password Cleaning CleaningElectronic Zoom EL-ZOOM Preset Alarm Preset ALMImage Hold Image Hold To Display the Camera Setting Menu Camera SettingCamera setting menu Camera Identification Camera IDBacklight compensation menu Turns to white Blinking Gain Control AGC Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLSync menu ATW fine adjustment menu Auto-Tracing White Balance Mode ATW1/ATW2White Balance White BAL AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 To Restore the Camera Default Position Refresh Black Burst Setting Burst BWCamera Resetting Camera Reset Initial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters Delay Time Delay Time Alarm Data Alarm DataUnit Number Unit Number Sub Address SUB AddressPrecautions InstallationMounting the Camera Ceiling mountDisassembling the Camera PreparationsMounting the Bracket Waterproof Material X4 Screws Upper BaseRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingHow to Assemble the Cable with the Accessory Connector AC Power Supply ConnectionConnections Alarm OUT Connections Alarm in ConnectionsRS485 Connection System Connections Signal-to-noise ratio SpecificationsPower consumption Prevention of Blooming and SmearOptional Accessories AccessoriesWV-7176E Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon