Panasonic WV-CW864 Pan Offset, To Set the Lens Zoom and Focus Positions, ZOOM/FOCUS setting menu

Page 17

3. Pan Offset

If the camera is replaced with a new one, the pan offset function is used to adjust its positions to be the same as before except patrol setting.

The system controller can download or upload the preset position data.

Caution: The preset data for other cameras (WV-CS850A for example) is incompatible with WV-CW864's. WV-CW864's preset data will be destroyed if you upload the conventional data. If this happened, reset the WV-CW864 to the default settings. Download the factory settings into the controller and upload the correct preset data newly to the initialized WV- CW864.

(1)Display the PRESET NUMBER SET menu.

(2)Select a position number for the picture to be most enlarged among the numbers by using the joystick. Then press the CAM (SET) key. The position setting menu appears.

(3)Move the cursor to PAN OFFSET SET and select the right or left arrow by using the joystick.

(4)Press the CAM (SET) key until the desired offset value appears.

(5)Move the cursor to an item other than PAN OFFSET SET, and press the MON (ESC) key.

Notes:

•Further adjustment of the other positions is unnecessary. This adjustment applies to all other positions.

•Make sure to move the cursor before pressing the key in step 5. Otherwise the settings will be ignored.

•Retry the loading when the camera fails to upload or down- load the data.

4.To Set the Lens Zoom and Focus Positions

(1)Move the cursor to PUSH SET for ZOOM/FOCUS and press the CAM (SET) key. The ZOOM/FOCUS setting menu appears.

(2)Select a zoom position by moving the zoom control up and down, and a focus position by moving the focus control up

and down, and then press the CAM (SET) key.

The positions are set and the screen returns to the position setting menu.

Notes:

•When the camera is used at a nearly horizontal angle, the focus may not be adjustable to a high level of accuracy.

•If you move the cursor to the position number and move the joystick right or left, the position number can be selected. The selected preset position number can also be set after pressing the CAM (SET) key.

•The preset and camera IDs appear in the lower-left corner of the position setting menu after setting them.

5.Move the cursor to RET and press the CAM (SET) key to return to the preset setting menu.

PRESET NUMBER SET menu

(1-32)

** PRESET NUMBER SET **

 

1

 

2

3

4

5

 

6

7

8

9

 

10

11

12

13

 

14

15

16

17

 

18

19

20

21

 

22

23

24

25

 

26

27

28

29

 

30

31

32

 

ID:DOOR

 

 

33-64

RET

 

 

Position setting menu

** POSITION 1 **

PAN/TILT

→

PUSH SET

ZOOM/FOCUS

→

PUSH SET

PAN OFFSET SET ← −0.0 →

RET

FLOOR1

DOOR

Position setting menu

** POSITION 1 **

PAN/TILT

→

PUSH SET

ZOOM/FOCUS

→

PUSH SET

PAN OFFSET SET ← −0.0 →

RET

FLOOR1

DOOR

ZOOM/FOCUS setting menu

 

 

** POSITION 1 **

 

PAN/TILT

→

PUSH SET

 

ZOOM/FOCUS

→

PUSH SET

 

 

 

 

 

 

 

 

 

PAN

U ZOOM D/L FOCUS R

 

→

 

OFFSET SET ←

−0.0

RET

 

 

 

 

 

FLOOR1

 

 

 

 

 

DOOR

 

 

 

 

 

Position setting menu

 

 

 

** POSITION 1 **

 

PAN/TILT

→

PUSH SET

 

ZOOM/FOCUS

→

PUSH SET

 

PAN OFFSET SET ←

−0.0 →

 

 

 

 

 

 

 

RET

 

 

 

 

 

FLOOR1

DOOR

18

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesCamera Cleaning PrecautionsPreset Data Uploading or Downloading Do not attempt to disassemble the cam- eraNever aim the camera at the sun Do not install the camera in places sub- ject to vibrationsIf Over Heat appears on the monitor screen ConsumablesConstruction Setup Menu SetupUp Switch Right Switch Left Switch Focus Switch Zoom SwitchSET Key CAM SET Key Down Switch Close CAM Setup F4 key Key for 2 sec Key for 2 secoPresetting Setup Menu DescriptionAuto Mode Auto Mode Home Position Home PositionDigital Flip Digital Flip Auto Pan Key Auto PAN KEYLocal/Remote LOCAL/REMOTE Special 1 MenuCamera Gain Control AGC Shutter Speed ShutterElectronic Sensitivity Enhancement Sens UP Synchronization SyncRS485 communication Setup Menu Display Setting ProceduresMenu Display Submenu DisplayPreset Menu Display PresettingPosition Setting Position SET To Set Panning/Tilting PositionsTo Set the Lens Zoom and Focus Positions ZOOM/FOCUS setting menuPan Offset To Enter a New Preset ID Preset Identification Setting Preset IDTo Copy a Preset ID from Another Position To Change an Entered Preset IDTo Set a Display Position for a Preset ID Light Control Setting ALC/MANUALTo Return to the Preset Setting Menu Manual setting menuPreset Speed Setting Preset Speed Scene File Setting Scene FileTo Return to the Preset Number Set Menu To Return to the Setup MenuSelf Return Setting Self Return Deleting Preset PositionsHome Position Setting Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingPrivacy Zone Privacy Zone Local/Remote Setting LOCAL/REMOTESpecial 1 Menu Setting Special Zone Scale setting menu Area Title Nesw setting menu When on Nesw is selectedProportional Pan/Tilt PROPO. P/T Area Title Area TitleDisplay Position setting menu Setting on UserDirection User setting menu Area Title EditingArea Title menu Patrol-learn and Patrol Play PatrolTo Quit Editing Patrol-learn with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyCNT-CLS 1, 2 Output Alarm Input/Output Alarm IN/OUTAlarm I/O submenu Password Verification Password Lock Password LockNew Password Cleaning CleaningImage Hold Image Hold Preset Alarm Preset ALMElectronic Zoom EL-ZOOM To Display the Camera Setting Menu Camera SettingCamera setting menu Camera Identification Camera IDBacklight compensation menu Turns to white Blinking Electronic Sensitivity Enhancement Sens UP Shutter Speed Setting ShutterGain Control AGC Sync menu Line-lock Sync Mode LLSynchronization Sync White Balance White BAL Auto-Tracing White Balance Mode ATW1/ATW2ATW fine adjustment menu AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 Camera Resetting Camera Reset Black Burst Setting Burst BWTo Restore the Camera Default Position Refresh Changing the Camera Communication Parameters RS485 SetupInitial Camera Communication Parameters Delay Time Delay Time Alarm Data Alarm DataUnit Number Unit Number Sub Address SUB AddressPrecautions InstallationMounting the Camera Ceiling mountDisassembling the Camera PreparationsMounting the Bracket Waterproof Material X4 Screws Upper BaseRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingConnections AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector RS485 Connection Alarm in ConnectionsAlarm OUT Connections System Connections Signal-to-noise ratio SpecificationsPower consumption Prevention of Blooming and SmearWV-7176E AccessoriesOptional Accessories Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon
Top Page Image Contents