Panasonic WV-CW864 Local/Remote Setting LOCAL/REMOTE, Special 1 Menu Setting Special

Page 25

■Local/Remote Setting (LOCAL/REMOTE)

•Move the cursor to LOCAL/REMOTE, and select LOCAL or REMOTE by moving the joystick to the right or left.

The factory default setting is LOCAL.

Note: The REMOTE mode does not work when the WV-RM70, WV-CU360, WV-CU161, WJ-FS616 or WV-CU550 series is connected. Make sure that LOCAL mode is selected in this case.

■Special 1 Menu Setting (SPECIAL 1)

●Privacy Zone (PRIVACY ZONE)

Up to 8 unwanted zones can be masked on the monitor screen.

1.Move the cursor to PRIVACY ZONE and select ON (ENB) or OFF (ENB) by moving the joystick to the right or left. Press the CAM (SET) key to display the ZONE NUMBER setting menu.

The factory default setting is OFF (ENB).

ON (ENB): Preset privacy zones are veiled on the monitor screen.

OFF (ENB): The veiling function does not work.

Note: If ON(DIS) or OFF(DIS) appears for PRIVACY ZONE, the steps from 2 onward are not applicable. Select OFF for PASS- WORD LOCK to take the following steps.

Setup menu

** SET UP MENU **

PRESET 1 MAP

HOME POSITION OFF

SELF RETURN OFF

AUTO MODE OFF

AUTO PAN KEY AUTO PAN DIGITAL FLIP ON LOCAL/REMOTE LOCAL SPECIAL1

CAMERA RS485 SET UP

Special 1 menu

** SPECIAL

1 **

PRIVACY ZONE

OFF(ENB)

PROPO.P/T

ON

AREA TITLE

ON(USER)

PATROL

STOP

ALARM IN/OUT

 

PASSWORD LOCK

OFF

CLEANING

OFF

EL-ZOOM

ON

PRESET ALM

OFF

IMAGE HOLD

OFF

RET

 

ZONE NUMBER setting menu

** ZONE NUMBER 1*/8 **

RET

2.Select a zone number by moving the joystick to the right or left, and press the CAM (SET) key.

•A zone number followed by * (asterisk) indicates that the zone has already been registered.

•When a zone number having no * is selected, the picture is zoomed out fully.

•When a registered zone number is selected, the camera moves to the preset position. Note that if you move PAN/TILT, ZOOM/FOCUS or ZONE SCALE in that position, the regis- tered zone number having “*” is cancelled.

•The zone frame appears in the center of the screen if 3 or fewer mask areas exist in that picture and if the zone number is not registered yet.

•The privacy zone may appear on the monitor screen depend- ing on the direction of the camera.

•The privacy zone function will not work at start-up immediate- ly after turning the power on.

ZONE setting menu

** ZONE NUMBER 1*/8 **

PAN/TILT →PUSH SET ZOOM/FOCUS →PUSH SET

ZONE SCALE

••••••••

SET DEL

–

+

RET

 

 

ZONE setting menu

** ZONE NUMBER 1*/8 **

PAN/TILT →PUSH SET ZOOM/FOCUS →PUSH SET

ZONE SCALE

••••••••

SET DEL

–

+

RET

 

 

26

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesCamera Cleaning PrecautionsPreset Data Uploading or Downloading Do not attempt to disassemble the cam- eraNever aim the camera at the sun Do not install the camera in places sub- ject to vibrationsIf Over Heat appears on the monitor screen ConsumablesConstruction Setup Menu SetupUp Switch Right Switch Left Switch Focus Switch Zoom SwitchSET Key CAM SET Key Down Switch Close CAM Setup F4 key Key for 2 sec Key for 2 secoPresetting Setup Menu DescriptionAuto Mode Auto Mode Home Position Home PositionDigital Flip Digital Flip Auto Pan Key Auto PAN KEYLocal/Remote LOCAL/REMOTE Special 1 MenuCamera Gain Control AGC Shutter Speed ShutterElectronic Sensitivity Enhancement Sens UP Synchronization SyncRS485 communication Setup Menu Display Setting ProceduresMenu Display Submenu DisplayPreset Menu Display PresettingPosition Setting Position SET To Set Panning/Tilting PositionsPan Offset ZOOM/FOCUS setting menuTo Set the Lens Zoom and Focus Positions To Enter a New Preset ID Preset Identification Setting Preset IDTo Copy a Preset ID from Another Position To Change an Entered Preset IDTo Set a Display Position for a Preset ID Light Control Setting ALC/MANUALTo Return to the Preset Setting Menu Manual setting menuPreset Speed Setting Preset Speed Scene File Setting Scene FileTo Return to the Preset Number Set Menu To Return to the Setup MenuHome Position Setting Deleting Preset PositionsSelf Return Setting Self Return Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingSpecial 1 Menu Setting Special Local/Remote Setting LOCAL/REMOTEPrivacy Zone Privacy Zone Zone Scale setting menu Area Title Nesw setting menu When on Nesw is selectedProportional Pan/Tilt PROPO. P/T Area Title Area TitleDisplay Position setting menu Setting on UserDirection User setting menu Area Title EditingTo Quit Editing Patrol-learn and Patrol Play PatrolArea Title menu Patrol-learn with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyAlarm I/O submenu Alarm Input/Output Alarm IN/OUTCNT-CLS 1, 2 Output Password Verification Password Lock Password LockNew Password Cleaning CleaningElectronic Zoom EL-ZOOM Preset Alarm Preset ALMImage Hold Image Hold To Display the Camera Setting Menu Camera SettingCamera setting menu Camera Identification Camera IDBacklight compensation menu Turns to white Blinking Gain Control AGC Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLSync menu ATW fine adjustment menu Auto-Tracing White Balance Mode ATW1/ATW2White Balance White BAL AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 To Restore the Camera Default Position Refresh Black Burst Setting Burst BWCamera Resetting Camera Reset Initial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters Delay Time Delay Time Alarm Data Alarm DataUnit Number Unit Number Sub Address SUB AddressPrecautions InstallationMounting the Camera Ceiling mountDisassembling the Camera PreparationsMounting the Bracket Waterproof Material X4 Screws Upper BaseRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingHow to Assemble the Cable with the Accessory Connector AC Power Supply ConnectionConnections Alarm OUT Connections Alarm in ConnectionsRS485 Connection System Connections Signal-to-noise ratio SpecificationsPower consumption Prevention of Blooming and SmearOptional Accessories AccessoriesWV-7176E Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon
Top Page Image Contents