Panasonic WV-CW864 Unit Number Unit Number, Sub Address SUB Address, Baud Rate Baud Rate

Page 47

Unit Number (UNIT NUMBER)

Displays the unit number set by the DIP switch. If the switch is set to 1-96, select a number by moving the joystick to the right or left. In an RS485 chain each unit must have a unique number.

Factory default setting: 1. See INSTALLATION for DIP switch setting.

Sub Address (SUB ADDRESS)

Do not set.

Baud Rate (BAUD RATE)

RS485 Setup menu

** RS485 SET UP **

UNIT NUMBER	1
SUB ADDRESS	-----
BAUD RATE	19200
DATA BIT	8
PARITY CHECK	NONE
STOP BIT	1
XON/XOFF	NOT USE
WAIT TIME	OFF
ALARM DATA	AUTO2
DELAY TIME	---
RET

Specifies the transmission speed (2 400, 4 800, 9 600, 19 200 bit per second) for the RS485 communica- tion. The factory default setting is 19 200.

Data Bit (DATA BIT)

Specifies the number of data bits (7 or 8 bits) for the RS485 communication. The factory default setting is 8.

Parity Check (PARITY CHECK)

Specifies the parity check mode (NONE, ODD, EVEN). The factory default setting is NONE.

Stop Bit (STOP BIT)

Specifies the number of stop bits (1 or 2 bits). The factory default setting is 1.

X ON/X OFF (X ON/X OFF)

Specifies whether to apply flow control or not (USE or NOT USE). The factory default setting is NOT USE.

Wait Time (WAIT TIME)

Specifies the time to wait until retrying after confirming that no data is received from the controller. (OFF: no retry, 100, 200, 400, 1 000 ms).

The factory default setting is OFF.

Alarm Data (ALARM DATA)

Specifies the alarm transmission mode depending on the protocol selected by the 8-bit DIP switch. POLLING: Transmits the alarm data in response to requests from the controller.

AUTO 1: Transmits the alarm data each time an alarm signal is received by the camera.

AUTO 2 (Default): Transmits alarm data at intervals of 5 seconds.

Delay Time (DELAY TIME)

Specifies the time to transmit the acknowledge request when communicating on a 2-line connection. [----, 100 ms] Factory default setting: ---- (no set).

This menu appears only when a 2-line communication is used. Make sure to be 100 ms when connecting the camera with the WJ-FS616 Video Multiplexer or Matrix Switcher WJ-SX350 in a 2-line communication system.

The settings become effective with the closing of SET UP MENU.

Note: Set the same parameters for the cameras, controllers and personal computers in an RS485 chain.

48

Image 47

Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesDo not attempt to disassemble the cam- era PrecautionsCamera Cleaning Preset Data Uploading or DownloadingConsumables Do not install the camera in places sub- ject to vibrationsNever aim the camera at the sun If Over Heat appears on the monitor screenConstruction Setup Menu SetupClose CAM Setup F4 key Key for 2 sec Key for 2 seco Focus Switch Zoom SwitchUp Switch Right Switch Left Switch SET Key CAM SET Key Down SwitchHome Position Home Position Setup Menu DescriptionPresetting Auto Mode Auto ModeSpecial 1 Menu Auto Pan Key Auto PAN KEYDigital Flip Digital Flip Local/Remote LOCAL/REMOTECamera Synchronization Sync Shutter Speed ShutterGain Control AGC Electronic Sensitivity Enhancement Sens UPRS485 communication Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions PresettingPreset Menu Display Position Setting Position SETTo Set the Lens Zoom and Focus Positions ZOOM/FOCUS setting menuPan Offset To Change an Entered Preset ID Preset Identification Setting Preset IDTo Enter a New Preset ID To Copy a Preset ID from Another PositionManual setting menu Light Control Setting ALC/MANUALTo Set a Display Position for a Preset ID To Return to the Preset Setting MenuTo Return to the Setup Menu Scene File Setting Scene FilePreset Speed Setting Preset Speed To Return to the Preset Number Set MenuSelf Return Setting Self Return Deleting Preset PositionsHome Position Setting Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingPrivacy Zone Privacy Zone Local/Remote Setting LOCAL/REMOTESpecial 1 Menu Setting Special Zone Scale setting menu Area Title Area Title When on Nesw is selectedArea Title Nesw setting menu Proportional Pan/Tilt PROPO. P/TArea Title Editing Setting on UserDisplay Position setting menu Direction User setting menuArea Title menu Patrol-learn and Patrol Play PatrolTo Quit Editing Patrol Play with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol-learn with a Controller not Having the Patrol Key Patrol Play with a Controller Having the Patrol KeyCNT-CLS 1, 2 Output Alarm Input/Output Alarm IN/OUTAlarm I/O submenu Password Verification Password Lock Password LockNew Password Cleaning CleaningImage Hold Image Hold Preset Alarm Preset ALMElectronic Zoom EL-ZOOM Camera Identification Camera ID Camera SettingTo Display the Camera Setting Menu Camera setting menuBacklight compensation menu Turns to white Blinking Electronic Sensitivity Enhancement Sens UP Shutter Speed Setting ShutterGain Control AGC Sync menu Line-lock Sync Mode LLSynchronization Sync White Balance White BAL Auto-Tracing White Balance Mode ATW1/ATW2ATW fine adjustment menu AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 Camera Resetting Camera Reset Black Burst Setting Burst BWTo Restore the Camera Default Position Refresh Changing the Camera Communication Parameters RS485 SetupInitial Camera Communication Parameters Sub Address SUB Address Alarm Data Alarm DataDelay Time Delay Time Unit Number Unit NumberCeiling mount InstallationPrecautions Mounting the CameraWaterproof Material X4 Screws Upper Base PreparationsDisassembling the Camera Mounting the BracketRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingConnections AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector RS485 Connection Alarm in ConnectionsAlarm OUT Connections System Connections Prevention of Blooming and Smear SpecificationsSignal-to-noise ratio Power consumptionWV-7176E AccessoriesOptional Accessories Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon