Panasonic WV-CW864 Precautions, Camera Cleaning, Preset Data Uploading or Downloading

Page 5

■Camera Cleaning

Even if this function is used, noise may be produced on the monitor screen, or the preset position may deviate in the course of prolonged use.

In such cases, activate the refresh mode on the special 2 menu. (See page 46.)

To use this camera with the WJ-SX550B Matrix Switcher, set the auto cleaning function activated on the Matrix Switcher side, then clean WV-CW864 one time a day.

■Preset Data Uploading or Downloading

To download the preset data from the camera to the controller or upload the downloaded data to the camera, set the following functions to OFF.

Downloading or uploading the data may not work normally if these functions are set to ON.

•Alarm (See page 32.)

•Preset alarm (See page 35.)

•Cleaning (See page 34.)

•Motion detection (See page 43.)

•Auto mode (See page 23.)

•Self return (See page 22.)

Aim the camera at a motionless object such as a wall, if possible, to download or upload the preset data.

Note: Take notice of the following when uploading the downloaded data to the camera.

•Preset positions may vary. If a preset position has deviated, delete the preset position and set the correct preset position newly.

•Uploading of WV-CW864 preset data to other models (e.g. WV-CS850A series) may cause an error and failure of the uploading process.

PRECAUTIONS

1.Do not attempt to disassemble the cam- era.

To prevent electric shock, do not remove screws or covers.

There are no user-serviceable parts inside. Ask a qualified service personnel for servic- ing.

2.Handle the camera with care.

Do not misuse the camera. Avoid striking, shaking, etc. The camera could be dam- aged by improper handling or storage.

3.Consult an expert on the load bearing capacity of the installation surface and structure. If the surface is not strong enough, the camera may fall down. Refer to the product specifications for weights.

4.Do not install the camera in places where it will be exposed to corrosive gasses, e.g., in chemical plants, seaside, at swim- ming pools or the like. Otherwise corro- sion of the bracket may cause the camera to fall down.

5.Use the fall-prevention wires to reduce the risk of the camera falling down.

Do not detach the fall-prevention wire secur- ing the camera. Otherwise the camera could fall down, causing injury to persons and damage to the camera.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesCamera Cleaning PrecautionsPreset Data Uploading or Downloading Do not attempt to disassemble the cam- eraNever aim the camera at the sun Do not install the camera in places sub- ject to vibrationsIf Over Heat appears on the monitor screen ConsumablesConstruction Setup Menu SetupUp Switch Right Switch Left Switch Focus Switch Zoom SwitchSET Key CAM SET Key Down Switch Close CAM Setup F4 key Key for 2 sec Key for 2 secoPresetting Setup Menu DescriptionAuto Mode Auto Mode Home Position Home PositionDigital Flip Digital Flip Auto Pan Key Auto PAN KEYLocal/Remote LOCAL/REMOTE Special 1 MenuCamera Gain Control AGC Shutter Speed ShutterElectronic Sensitivity Enhancement Sens UP Synchronization SyncRS485 communication Setup Menu Display Setting ProceduresMenu Display Submenu DisplayPreset Menu Display PresettingPosition Setting Position SET To Set Panning/Tilting PositionsTo Set the Lens Zoom and Focus Positions ZOOM/FOCUS setting menuPan Offset To Enter a New Preset ID Preset Identification Setting Preset IDTo Copy a Preset ID from Another Position To Change an Entered Preset IDTo Set a Display Position for a Preset ID Light Control Setting ALC/MANUALTo Return to the Preset Setting Menu Manual setting menuPreset Speed Setting Preset Speed Scene File Setting Scene FileTo Return to the Preset Number Set Menu To Return to the Setup MenuSelf Return Setting Self Return Deleting Preset PositionsHome Position Setting Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingPrivacy Zone Privacy Zone Local/Remote Setting LOCAL/REMOTESpecial 1 Menu Setting Special Zone Scale setting menu Area Title Nesw setting menu When on Nesw is selectedProportional Pan/Tilt PROPO. P/T Area Title Area TitleDisplay Position setting menu Setting on UserDirection User setting menu Area Title EditingArea Title menu Patrol-learn and Patrol Play PatrolTo Quit Editing Patrol-learn with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol Play with a Controller Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyCNT-CLS 1, 2 Output Alarm Input/Output Alarm IN/OUTAlarm I/O submenu Password Verification Password Lock Password LockNew Password Cleaning CleaningImage Hold Image Hold Preset Alarm Preset ALMElectronic Zoom EL-ZOOM To Display the Camera Setting Menu Camera SettingCamera setting menu Camera Identification Camera IDBacklight compensation menu Turns to white Blinking Electronic Sensitivity Enhancement Sens UP Shutter Speed Setting ShutterGain Control AGC Sync menu Line-lock Sync Mode LLSynchronization Sync White Balance White BAL Auto-Tracing White Balance Mode ATW1/ATW2ATW fine adjustment menu AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 Camera Resetting Camera Reset Black Burst Setting Burst BWTo Restore the Camera Default Position Refresh Changing the Camera Communication Parameters RS485 SetupInitial Camera Communication Parameters Delay Time Delay Time Alarm Data Alarm DataUnit Number Unit Number Sub Address SUB AddressPrecautions InstallationMounting the Camera Ceiling mountDisassembling the Camera PreparationsMounting the Bracket Waterproof Material X4 Screws Upper BaseRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingConnections AC Power Supply ConnectionHow to Assemble the Cable with the Accessory Connector RS485 Connection Alarm in ConnectionsAlarm OUT Connections System Connections Signal-to-noise ratio SpecificationsPower consumption Prevention of Blooming and SmearWV-7176E AccessoriesOptional Accessories Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon
Top Page Image Contents