Panasonic WV-CW864 operating instructions RS485 Setup, Initial Camera Communication Parameters

Page 46

(9)Digital Noise Reduction (DNR)

DNR may be used to improve quality under low light condi- tions. There are 4 levels of DNR, which may be selected depending on local site conditions. Factory default setting: LOW2

You may need to try different settings to find the most suitable conditions for your application.

Move the cursor to DNR and select LOW1, LOW2, HIGH1 or HIGH2 by moving the joystick to the right or left.

LOW1: DNR level is low. The after-image remains.

LOW2: DNR level is low. The after-image is reduced.

HIGH1: DNR level is high. The after-image remains.

HIGH2: DNR level is high. The after-image is reduced.

(10)To Close the SPECIAL2 Menu

Move the cursor to RET and press the CAM (SET) key. The setup menu appears on the monitor screen.

Reset to the Factory Default Settings

Any of the above settings plus the ALC/MANUAL level control and phase adjustments can be reset to the factory default settings by placing the cursor over the desired mode and then pressing the F2 button of the WV-CU550B.

For the WV-RM70, keep pressing the Right and Left switches simultaneously for 2 seconds or more.

** SPECIAL2 **

CHROMA GAIN

••••••••

AP GAIN

••••••••

PEDESTAL

••••••••

HUE

••••••••

 

 

-

+

BW

 

 

OFF

BURST(BW)

→

 

ON

REFRESH

PUSH SW

CAMERA RESET

→

PUSH SW

DNR

 

 

LOW2

 

RET

 

 

 

 

 

** SPECIAL2 **

CHROMA GAIN

••••••••

AP GAIN

••••••••

PEDESTAL

••••••••

HUE

••••••••

 

 

-

+

BW

 

 

OFF

BURST(BW)

→

 

ON

REFRESH

PUSH SW

CAMERA RESET

→

PUSH SW

DNR

 

 

LOW2

RET

 

 

 

 

 

■RS485 Setup

●Initial Camera Communication Parameters

In an RS485 chain, the matrix switcher, PC, controllers and cam- eras should be set to the same protocol and parameters for com- munication. Confirm the system protocol and parameters prior to setting the communication parameters for the camera.

The initial communication parameters for WV-CW864 are shown on the RS485 setup menu below. Other than the on-screen setup parameters, the 4-bit DIP switch may be used to select 2-line (Half Duplex) or 4-line (Full Duplex) communication.

●Changing the Camera Communication Parameters

You can remotely control this camera by using a specified exten- sion unit such as a computer with a modem.

1.Display the SET UP MENU. Move the cursor to RS485 SET UP and press the CAM (SET) key. The RS485 SET UP menu appears on the monitor.

2.Move the cursor to the item and select the parameter by mov- ing the joystick to the right or left.

RS485 Setup menu

** RS485 SET UP **

UNIT NUMBER

1

 

SUB ADDRESS

-----

BAUD RATE

19200

DATA BIT

8

 

PARITY CHECK

NONE

STOP BIT

1

 

XON/XOFF

NOT USE

WAIT TIME

OFF

ALARM DATA

AUTO2

DELAY TIME

---

RET

 

 

47

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Operating Instructions Contents Important Safety Instructions EnglishFeatures PrefacePreset Data Uploading or Downloading PrecautionsCamera Cleaning Do not attempt to disassemble the cam- eraIf Over Heat appears on the monitor screen Do not install the camera in places sub- ject to vibrationsNever aim the camera at the sun ConsumablesConstruction Setup Setup MenuSET Key CAM SET Key Down Switch Focus Switch Zoom SwitchUp Switch Right Switch Left Switch Close CAM Setup F4 key Key for 2 sec Key for 2 secoAuto Mode Auto Mode Setup Menu DescriptionPresetting Home Position Home PositionLocal/Remote LOCAL/REMOTE Auto Pan Key Auto PAN KEYDigital Flip Digital Flip Special 1 MenuCamera Electronic Sensitivity Enhancement Sens UP Shutter Speed ShutterGain Control AGC Synchronization SyncRS485 communication Menu Display Setting ProceduresSetup Menu Display Submenu DisplayPosition Setting Position SET PresettingPreset Menu Display To Set Panning/Tilting PositionsPan Offset ZOOM/FOCUS setting menuTo Set the Lens Zoom and Focus Positions To Copy a Preset ID from Another Position Preset Identification Setting Preset IDTo Enter a New Preset ID To Change an Entered Preset IDTo Return to the Preset Setting Menu Light Control Setting ALC/MANUALTo Set a Display Position for a Preset ID Manual setting menuTo Return to the Preset Number Set Menu Scene File Setting Scene FilePreset Speed Setting Preset Speed To Return to the Setup MenuHome Position Setting Deleting Preset PositionsSelf Return Setting Self Return Auto Mode Selection Auto Mode Auto PAN setting menuWhen the panning, tilting, zooming or focusing in the SEQ Auto Pan Key Setting Digital Flip Setting Digital FlipSpecial 1 Menu Setting Special Local/Remote Setting LOCAL/REMOTEPrivacy Zone Privacy Zone Zone Scale setting menu Proportional Pan/Tilt PROPO. P/T When on Nesw is selectedArea Title Nesw setting menu Area Title Area TitleDirection User setting menu Setting on UserDisplay Position setting menu Area Title EditingTo Quit Editing Patrol-learn and Patrol Play PatrolArea Title menu Patrol Play with a Controller Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol-learn with a Controller not Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyAlarm I/O submenu Alarm Input/Output Alarm IN/OUTCNT-CLS 1, 2 Output Password Lock Password Lock Password VerificationCleaning Cleaning New PasswordElectronic Zoom EL-ZOOM Preset Alarm Preset ALMImage Hold Image Hold Camera setting menu Camera SettingTo Display the Camera Setting Menu Camera Identification Camera IDBacklight compensation menu Turns to white Blinking Gain Control AGC Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLSync menu ATW fine adjustment menu Auto-Tracing White Balance Mode ATW1/ATW2White Balance White BAL Automatic White Balance Control Mode AWC AWC fine adjustment menuMotion Detector Motion DET Motion detect menuAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 To Restore the Camera Default Position Refresh Black Burst Setting Burst BWCamera Resetting Camera Reset Initial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters Unit Number Unit Number Alarm Data Alarm DataDelay Time Delay Time Sub Address SUB AddressMounting the Camera InstallationPrecautions Ceiling mountMounting the Bracket PreparationsDisassembling the Camera Waterproof Material X4 Screws Upper BaseSetting the Switches RS485 Parameter SetupFor Panasonic’s Protocol Unit NumberSwitch position Unit RS485 Setting Mounting the cameraHow to Assemble the Cable with the Accessory Connector AC Power Supply ConnectionConnections Alarm OUT Connections Alarm in ConnectionsRS485 Connection System Connections Power consumption SpecificationsSignal-to-noise ratio Prevention of Blooming and SmearOptional Accessories AccessoriesWV-7176E Appendix ShortcutsN0202-1032 V8QA5996BN Imprimé au Japon Regional Offices
Top Page Image Contents