Panasonic WV-CW864 Alarm Input/Output Alarm IN/OUT, CNT-CLS 1, 2 Output, Alarm I/O submenu

Page 31

Alarm Input/Output (ALARM IN/OUT)

Move the cursor to ALARM IN/OUT, and press the CAM (SET) key. The ALARM IN/OUT submenu appears.

Note: While the camera is in the AF mode or the lens moves between WIDE and TELE, alarm input may be ignored if several alarm inputs are received in succession.

ALARM IN 1-4

Alarm input signals are supplied from external devices through the ALARM IN connector to turn the camera to a preset position.

1.Move the cursor to ALARM IN 1* and select a preset position or OFF by moving the joystick, then press the CAM (SET) key.

The factory default setting is OFF.

*Set ALARM IN 2, 3 and 4 in the same way as ALARM IN 1.

1POSI, 2 POSI, 3 POSI and 4 POSI: Preset position. If an alarm input is received, the camera turns to a preset position, and sends an alarm output signal. The position number corre-

sponds to the alarm input numbers (1-1, 2-2, 3-3 and 4-4). B/W: Available for ALARM INPUT 4 only. The camera changes its

mode from color to black and white if ALARM IN 4 is sup- plied.

OFF: The camera ignores alarm inputs.

Note: If two or more alarm inputs are received while the camera is moving to a preset position, the camera starts to aim at preset positions in small preset numerical order after current posi- tioning.

CNT-CLS 1, 2 (Output)

Special 1 menu

** SPECIAL 1 **

PRIVACY ZONE

OFF(ENB)

PROPO.P/T

ON

AREA TITLE

ON(USER)

PATROL

STOP

ALARM IN/OUT

 

 

PASSWORD LOCK

OFF

CLEANING

OFF

EL-ZOOM

ON

PRESET ALM

OFF

IMAGE HOLD

OFF

RET

 

 

ALARM I/O submenu

**

ALARM IN/OUT **

ALARM

IN

1

OFF

ALARM

IN

2

OFF

ALARM

IN

3

OFF

ALARM

IN

4

OFF

CNT-CLS 1

 

OFF

TIME

OUT

 

100MS

CNT-CLS 2

 

OFF

COAX ALM OUT

OFF

RET

Two contact closure signals (Open collector type) are output through the Alarm Output connector.

1.Move the cursor to CNT-CLS 1, and select OFF, ALARM or AUX 1 by moving the joystick to the right or left.

The factory default setting is OFF.

When ALARM is selected, TIME OUT appears. Select an appropriate duration from among 100 MS, 200 MS, 1000 MS (1 s), 2000 MS (2 s) or 4000 MS (4 s) by moving the joystick to the right or left.

The factory default setting is 100 MS.

Note: The shorter the duration, the more frequent will be the detection output.

2.Move the cursor to CNT-CLS 2, then select OFF, B/W or AUX 2 by moving the joystick to the right or left.

The factory default setting is OFF.

OFF: Contact closure signals are deactivated.

ALM: Available for CNT-CLS 1 only. A motion detection signal is output.

AUX 1(2): An alarm signal is output when the camera receives a command from the controller.

B/W: Available for CNT-CLS 2 only. ON (active) is output when the camera operates in the black and white mode if ALARM IN 4 is set to B/W.

Note: It is recommended to set the connected external device to ignore the shorter alarm outputs of 90 ms or less from the camera.

32

Image 31
Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesDo not attempt to disassemble the cam- era PrecautionsCamera Cleaning Preset Data Uploading or DownloadingConsumables Do not install the camera in places sub- ject to vibrationsNever aim the camera at the sun If Over Heat appears on the monitor screenConstruction Setup Menu SetupClose CAM Setup F4 key Key for 2 sec Key for 2 seco Focus Switch Zoom SwitchUp Switch Right Switch Left Switch SET Key CAM SET Key Down SwitchHome Position Home Position Setup Menu DescriptionPresetting Auto Mode Auto ModeSpecial 1 Menu Auto Pan Key Auto PAN KEYDigital Flip Digital Flip Local/Remote LOCAL/REMOTECamera Synchronization Sync Shutter Speed ShutterGain Control AGC Electronic Sensitivity Enhancement Sens UPRS485 communication Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions PresettingPreset Menu Display Position Setting Position SETPan Offset ZOOM/FOCUS setting menuTo Set the Lens Zoom and Focus Positions To Change an Entered Preset ID Preset Identification Setting Preset IDTo Enter a New Preset ID To Copy a Preset ID from Another PositionManual setting menu Light Control Setting ALC/MANUALTo Set a Display Position for a Preset ID To Return to the Preset Setting MenuTo Return to the Setup Menu Scene File Setting Scene FilePreset Speed Setting Preset Speed To Return to the Preset Number Set MenuHome Position Setting Deleting Preset PositionsSelf Return Setting Self Return Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingSpecial 1 Menu Setting Special Local/Remote Setting LOCAL/REMOTEPrivacy Zone Privacy Zone Zone Scale setting menu Area Title Area Title When on Nesw is selectedArea Title Nesw setting menu Proportional Pan/Tilt PROPO. P/TArea Title Editing Setting on UserDisplay Position setting menu Direction User setting menuTo Quit Editing Patrol-learn and Patrol Play PatrolArea Title menu Patrol Play with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol-learn with a Controller not Having the Patrol Key Patrol Play with a Controller Having the Patrol KeyAlarm I/O submenu Alarm Input/Output Alarm IN/OUTCNT-CLS 1, 2 Output Password Verification Password Lock Password LockNew Password Cleaning CleaningElectronic Zoom EL-ZOOM Preset Alarm Preset ALMImage Hold Image Hold Camera Identification Camera ID Camera SettingTo Display the Camera Setting Menu Camera setting menuBacklight compensation menu Turns to white Blinking Gain Control AGC Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLSync menu ATW fine adjustment menu Auto-Tracing White Balance Mode ATW1/ATW2White Balance White BAL AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 To Restore the Camera Default Position Refresh Black Burst Setting Burst BWCamera Resetting Camera Reset Initial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters Sub Address SUB Address Alarm Data Alarm DataDelay Time Delay Time Unit Number Unit NumberCeiling mount InstallationPrecautions Mounting the CameraWaterproof Material X4 Screws Upper Base PreparationsDisassembling the Camera Mounting the BracketRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingHow to Assemble the Cable with the Accessory Connector AC Power Supply ConnectionConnections Alarm OUT Connections Alarm in ConnectionsRS485 Connection System Connections Prevention of Blooming and Smear SpecificationsSignal-to-noise ratio Power consumptionOptional Accessories AccessoriesWV-7176E Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon