Panasonic WV-CW864 Setting Procedures, Setup Menu Display, Submenu Display

Page 15

SETTING PROCEDURES

The following setting procedures are described on the assumption that this model is used in combination with the WJ-SX550B Matrix Switcher and WV-CU550B System Controller. In case a controller other than the WV-CU550B is used, refer to the table on page 10.

■Menu Display

●Setup Menu Display

WV-CU550B

1.Select the camera number you want to set up and a monitor to display SET UP MENU.

2.Display the D4 menu on the LCD by pressing the appropriate cur- sor buttons.

3.Press the F1 button.

SET UP MENU appears on the monitor screen.

4.To close SET UP MENU, press the F4 button.

WV-CU360

Press the CAM SETUP key for 2 seconds or more to open the SETUP menu.

WV-CU161

Press the CAMERA SETUP key for 2 seconds or more to open the SETUP menu.

WV-RM70

1.Turn the MODE SELECTION switch to NORMAL or ALARM OFF.

2.Press the PROG switch for 2 seconds or more to open the Program Menu.

3.Move the cursor to Camera Set Up Menu, and press the SET switch to open the SETUP MENU.

●Submenu Display

The items marked O can be selected/changed on the submenu.

•Move the cursor to an item with the O mark and press the CAM (SET) key. The submenu appears.

D4 menu

Camera Set Up Menu

OnExit

F1 F2 F3 F4

Camera Set Up Menu Res A.Res Exit

F1 F2 F3 F4

Setup menu

** SET UP MENU **

PRESET 1 MAP

HOME POSITION OFF

SELF RETURN OFF

AUTO MODE OFF AUTO PAN KEY AUTO PAN DIGITAL FLIP ON LOCAL/REMOTE LOCAL SPECIAL1

CAMERA RS485 SET UP

Submenu

(for RS485 setup)

** RS485 SET UP **

UNIT NUMBER	1
SUB ADDRESS	-----
BAUD RATE	19200
DATA BIT	8
PARITY CHECK	NONE
STOP BIT	1
XON/XOFF	NOT USE
WAIT TIME	OFF
ALARM DATA	AUTO2
DELAY TIME	---
RET

16

Image 15

Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesDo not attempt to disassemble the cam- era PrecautionsCamera Cleaning Preset Data Uploading or DownloadingConsumables Do not install the camera in places sub- ject to vibrationsNever aim the camera at the sun If Over Heat appears on the monitor screenConstruction Setup Menu SetupClose CAM Setup F4 key Key for 2 sec Key for 2 seco Focus Switch Zoom SwitchUp Switch Right Switch Left Switch SET Key CAM SET Key Down SwitchHome Position Home Position Setup Menu DescriptionPresetting Auto Mode Auto ModeSpecial 1 Menu Auto Pan Key Auto PAN KEYDigital Flip Digital Flip Local/Remote LOCAL/REMOTECamera Synchronization Sync Shutter Speed ShutterGain Control AGC Electronic Sensitivity Enhancement Sens UPRS485 communication Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions PresettingPreset Menu Display Position Setting Position SETZOOM/FOCUS setting menu Pan OffsetTo Set the Lens Zoom and Focus Positions To Change an Entered Preset ID Preset Identification Setting Preset IDTo Enter a New Preset ID To Copy a Preset ID from Another PositionManual setting menu Light Control Setting ALC/MANUALTo Set a Display Position for a Preset ID To Return to the Preset Setting MenuTo Return to the Setup Menu Scene File Setting Scene FilePreset Speed Setting Preset Speed To Return to the Preset Number Set MenuDeleting Preset Positions Home Position SettingSelf Return Setting Self Return Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingLocal/Remote Setting LOCAL/REMOTE Special 1 Menu Setting SpecialPrivacy Zone Privacy Zone Zone Scale setting menu Area Title Area Title When on Nesw is selectedArea Title Nesw setting menu Proportional Pan/Tilt PROPO. P/TArea Title Editing Setting on UserDisplay Position setting menu Direction User setting menuPatrol-learn and Patrol Play Patrol To Quit EditingArea Title menu Patrol Play with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol-learn with a Controller not Having the Patrol Key Patrol Play with a Controller Having the Patrol KeyAlarm Input/Output Alarm IN/OUT Alarm I/O submenuCNT-CLS 1, 2 Output Password Verification Password Lock Password LockNew Password Cleaning CleaningPreset Alarm Preset ALM Electronic Zoom EL-ZOOMImage Hold Image Hold Camera Identification Camera ID Camera SettingTo Display the Camera Setting Menu Camera setting menuBacklight compensation menu Turns to white Blinking Shutter Speed Setting Shutter Gain Control AGCElectronic Sensitivity Enhancement Sens UP Line-lock Sync Mode LL Synchronization SyncSync menu Auto-Tracing White Balance Mode ATW1/ATW2 ATW fine adjustment menuWhite Balance White BAL AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 Black Burst Setting Burst BW To Restore the Camera Default Position RefreshCamera Resetting Camera Reset RS485 Setup Initial Camera Communication ParametersChanging the Camera Communication Parameters Sub Address SUB Address Alarm Data Alarm DataDelay Time Delay Time Unit Number Unit NumberCeiling mount InstallationPrecautions Mounting the CameraWaterproof Material X4 Screws Upper Base PreparationsDisassembling the Camera Mounting the BracketRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingAC Power Supply Connection How to Assemble the Cable with the Accessory ConnectorConnections Alarm in Connections Alarm OUT ConnectionsRS485 Connection System Connections Prevention of Blooming and Smear SpecificationsSignal-to-noise ratio Power consumptionAccessories Optional AccessoriesWV-7176E Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon