Panasonic WV-CW864 RS485 Connection, Alarm in Connections, Alarm OUT Connections

Page 55

• RS485 Connection

Data transmission

Data reception

Brown

Red

Orange

Yellow

Green

GND

T(B) T (A) R (B) R (A)

Note:

Use the cable that is described below for RS485 site communication.

•Shielded, twisted pair cable

•Low impedance

•Wire gauge size is thicker than AWG #22 (0.33 mm2).

•ALARM IN Connections

An 8-pin and a 4-pin harness are supplied with the camera as standard accessories. Connect exter- nal sensors to this connector. Input specifications are low-active, non-voltage contact (ON when active) or open collector (Low when active). The table below shows wire colors versus pin functions.

	Alarm IN (8-pin)
Wire color		Function

Black		IN 1
Brown		GND
Red		IN 2
Orange		GND
Yellow		IN 3
Light blue or green		GND
Blue		IN 4
Purple		GND

•ALARM OUT Connections

Connect an external device, for example, a buzzer or lamp, to this connector. Output specifications are low-active, open-collector and a drive capacity of 16 V DC 100 mA maximum. The table below shows wire colors versus pin functions.

Alarm OUT (4-pin)

Wire color	Function

Gray	OUT 1
White	GND
Pink	OUT 2
Yellow green or light blue	GND

Note: Use a relay if the voltage or current of the connected device exceeds the ratings.

56

Image 55

Contents Operating Instructions Contents English Important Safety InstructionsPreface FeaturesDo not attempt to disassemble the cam- era PrecautionsCamera Cleaning Preset Data Uploading or DownloadingConsumables Do not install the camera in places sub- ject to vibrationsNever aim the camera at the sun If Over Heat appears on the monitor screenConstruction Setup Menu SetupClose CAM Setup F4 key Key for 2 sec Key for 2 seco Focus Switch Zoom SwitchUp Switch Right Switch Left Switch SET Key CAM SET Key Down SwitchHome Position Home Position Setup Menu DescriptionPresetting Auto Mode Auto ModeSpecial 1 Menu Auto Pan Key Auto PAN KEYDigital Flip Digital Flip Local/Remote LOCAL/REMOTECamera Synchronization Sync Shutter Speed ShutterGain Control AGC Electronic Sensitivity Enhancement Sens UPRS485 communication Submenu Display Setting ProceduresSetup Menu Display Menu DisplayTo Set Panning/Tilting Positions PresettingPreset Menu Display Position Setting Position SETPan Offset ZOOM/FOCUS setting menuTo Set the Lens Zoom and Focus Positions To Change an Entered Preset ID Preset Identification Setting Preset IDTo Enter a New Preset ID To Copy a Preset ID from Another PositionManual setting menu Light Control Setting ALC/MANUALTo Set a Display Position for a Preset ID To Return to the Preset Setting MenuTo Return to the Setup Menu Scene File Setting Scene FilePreset Speed Setting Preset Speed To Return to the Preset Number Set MenuHome Position Setting Deleting Preset PositionsSelf Return Setting Self Return Auto PAN setting menu Auto Mode Selection Auto ModeWhen the panning, tilting, zooming or focusing in the SEQ Digital Flip Setting Digital Flip Auto Pan Key SettingSpecial 1 Menu Setting Special Local/Remote Setting LOCAL/REMOTEPrivacy Zone Privacy Zone Zone Scale setting menu Area Title Area Title When on Nesw is selectedArea Title Nesw setting menu Proportional Pan/Tilt PROPO. P/TArea Title Editing Setting on UserDisplay Position setting menu Direction User setting menuTo Quit Editing Patrol-learn and Patrol Play PatrolArea Title menu Patrol Play with a Controller not Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol-learn with a Controller not Having the Patrol Key Patrol Play with a Controller Having the Patrol KeyAlarm I/O submenu Alarm Input/Output Alarm IN/OUTCNT-CLS 1, 2 Output Password Verification Password Lock Password LockNew Password Cleaning CleaningElectronic Zoom EL-ZOOM Preset Alarm Preset ALMImage Hold Image Hold Camera Identification Camera ID Camera SettingTo Display the Camera Setting Menu Camera setting menuBacklight compensation menu Turns to white Blinking Gain Control AGC Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Synchronization Sync Line-lock Sync Mode LLSync menu ATW fine adjustment menu Auto-Tracing White Balance Mode ATW1/ATW2White Balance White BAL AWC fine adjustment menu Automatic White Balance Control Mode AWCMotion detect menu Motion Detector Motion DETAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 To Restore the Camera Default Position Refresh Black Burst Setting Burst BWCamera Resetting Camera Reset Initial Camera Communication Parameters RS485 SetupChanging the Camera Communication Parameters Sub Address SUB Address Alarm Data Alarm DataDelay Time Delay Time Unit Number Unit NumberCeiling mount InstallationPrecautions Mounting the CameraWaterproof Material X4 Screws Upper Base PreparationsDisassembling the Camera Mounting the BracketRS485 Parameter Setup Setting the SwitchesUnit Number For Panasonic’s ProtocolSwitch position Unit Mounting the camera RS485 SettingHow to Assemble the Cable with the Accessory Connector AC Power Supply ConnectionConnections Alarm OUT Connections Alarm in ConnectionsRS485 Connection System Connections Prevention of Blooming and Smear SpecificationsSignal-to-noise ratio Power consumptionOptional Accessories AccessoriesWV-7176E Shortcuts AppendixRegional Offices N0202-1032 V8QA5996BN Imprimé au Japon