Panasonic WV-CW864 operating instructions Connections, AC Power Supply Connection

Page 54

CONNECTIONS

Precautions

•The following connections should be made by qualified service personnel or system installers in accordance with all local codes.

•Switch the 24 V AC power source off before installation and connection.

24 V AC cable for Heater

24 V AC

Data port

24 V AC cable for Camera

RS485 cable

Coaxial cable

Video output	Alarm in	BNC plug	BNC plug

To VIDEO IN

(CAMERA IN)

To sensors

To indicators

Alarm out

✻ The coaxial cable length (RG-59/U, BELDEN 9259) for the connec- tion is up to 900 meters (3 000 ft.)

Note: When powered up, the unit performs a self-check (including one panning, tilting, zooming and focusing operation).

• 24 V AC Power Supply Connection

Recommended wire gauge sizes for 24 V AC line

Copper wire size		#24		#22			#20				#18
(AWG)		(0.22mm2)	(0.33mm2)			(0.52mm2)					(0.83mm2)

Length	(m)	20		30			45				75
of cable
of cable	(ft)	65		100			160				260
(approx.)	(ft)	65		100			160				260

Accessory Connector Information

Pin no.		Power source

1	24 V AC LIVE
1	24 V AC LIVE
2	24 V AC NEUTRAL							4				3
3	Ground
3	Ground							2			1
4	Not use

Prepare the individual conductors for clamping. Use MOLEX band tool part number 57027-5000 (for UL-Style Cable UL1015) or 57026-5000 (for UL-Style UL1007) for clamping the contacts.

After clamping the contacts, push them into the proper holes in the accessory connector of this camera until they snap in place.

Up

Wire

Contact

How to Assemble the Cable with the Accessory Connector

Strip back the cable jacket approx. 3 mm (0.1 inch) and separate the individual conductors.

Approx.

Approx.

	3	(0.1 inch)
			Wire
	3 mm (0.1 inch)

Up A

Contact

Insert

InsertIns the wireire untiluntilAApositpositionon

anda clampl the contactst cts..

CAUTIONS

•Shrinking the cable-entry seal is a one- time procedure. Do not shrink the cable- entry seal until it has been ascertained that the unit is functioning.

•CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY.

55

Image 54

Contents Operating Instructions Contents Important Safety Instructions EnglishFeatures PrefacePreset Data Uploading or Downloading PrecautionsCamera Cleaning Do not attempt to disassemble the cam- eraIf Over Heat appears on the monitor screen Do not install the camera in places sub- ject to vibrationsNever aim the camera at the sun ConsumablesConstruction Setup Setup MenuSET Key CAM SET Key Down Switch Focus Switch Zoom SwitchUp Switch Right Switch Left Switch Close CAM Setup F4 key Key for 2 sec Key for 2 secoAuto Mode Auto Mode Setup Menu DescriptionPresetting Home Position Home PositionLocal/Remote LOCAL/REMOTE Auto Pan Key Auto PAN KEYDigital Flip Digital Flip Special 1 MenuCamera Electronic Sensitivity Enhancement Sens UP Shutter Speed ShutterGain Control AGC Synchronization SyncRS485 communication Menu Display Setting ProceduresSetup Menu Display Submenu DisplayPosition Setting Position SET PresettingPreset Menu Display To Set Panning/Tilting PositionsZOOM/FOCUS setting menu Pan OffsetTo Set the Lens Zoom and Focus Positions To Copy a Preset ID from Another Position Preset Identification Setting Preset IDTo Enter a New Preset ID To Change an Entered Preset IDTo Return to the Preset Setting Menu Light Control Setting ALC/MANUALTo Set a Display Position for a Preset ID Manual setting menuTo Return to the Preset Number Set Menu Scene File Setting Scene FilePreset Speed Setting Preset Speed To Return to the Setup MenuDeleting Preset Positions Home Position SettingSelf Return Setting Self Return Auto Mode Selection Auto Mode Auto PAN setting menuWhen the panning, tilting, zooming or focusing in the SEQ Auto Pan Key Setting Digital Flip Setting Digital FlipLocal/Remote Setting LOCAL/REMOTE Special 1 Menu Setting SpecialPrivacy Zone Privacy Zone Zone Scale setting menu Proportional Pan/Tilt PROPO. P/T When on Nesw is selectedArea Title Nesw setting menu Area Title Area TitleDirection User setting menu Setting on UserDisplay Position setting menu Area Title EditingPatrol-learn and Patrol Play Patrol To Quit EditingArea Title menu Patrol Play with a Controller Having the Patrol Key Patrol-learn with a Controller Having the Patrol KeyPatrol-learn with a Controller not Having the Patrol Key Patrol Play with a Controller not Having the Patrol KeyAlarm Input/Output Alarm IN/OUT Alarm I/O submenuCNT-CLS 1, 2 Output Password Lock Password Lock Password VerificationCleaning Cleaning New PasswordPreset Alarm Preset ALM Electronic Zoom EL-ZOOMImage Hold Image Hold Camera setting menu Camera SettingTo Display the Camera Setting Menu Camera Identification Camera IDBacklight compensation menu Turns to white Blinking Shutter Speed Setting Shutter Gain Control AGCElectronic Sensitivity Enhancement Sens UP Line-lock Sync Mode LL Synchronization SyncSync menu Auto-Tracing White Balance Mode ATW1/ATW2 ATW fine adjustment menuWhite Balance White BAL Automatic White Balance Control Mode AWC AWC fine adjustment menuMotion Detector Motion DET Motion detect menuAuto Focus Setting AF Mode Special 2 Menu SPECIAL2 Black Burst Setting Burst BW To Restore the Camera Default Position RefreshCamera Resetting Camera Reset RS485 Setup Initial Camera Communication ParametersChanging the Camera Communication Parameters Unit Number Unit Number Alarm Data Alarm DataDelay Time Delay Time Sub Address SUB AddressMounting the Camera InstallationPrecautions Ceiling mountMounting the Bracket PreparationsDisassembling the Camera Waterproof Material X4 Screws Upper BaseSetting the Switches RS485 Parameter SetupFor Panasonic’s Protocol Unit NumberSwitch position Unit RS485 Setting Mounting the cameraAC Power Supply Connection How to Assemble the Cable with the Accessory ConnectorConnections Alarm in Connections Alarm OUT ConnectionsRS485 Connection System Connections Power consumption SpecificationsSignal-to-noise ratio Prevention of Blooming and SmearAccessories Optional AccessoriesWV-7176E Appendix ShortcutsN0202-1032 V8QA5996BN Imprimé au Japon Regional Offices