Pioneer DJM-800 operating instructions Beat Effect, Effect Functions Effect Parameters

EFFECT FUNCTIONS (EFFECT PARAMETERS)

EFFECT PARAMETERS

Beat Effect

	Name	Beat Switch Parameter	Parameter 1 (TIME dial)		Parameter 2
			Contents	Setting Range (unit)	(MIX/DEPTH dial) contents
1	DELAY	Sets delay time of 1/8 to 16/1 per 1	Sets delay time.	1 to 4 000 (ms)	Sets balance between original and
		beat of BPM time.			delay sound.
2	ECHO (*1)	Sets delay time of 1/8 to 16/1 per 1	Sets delay time.	1 to 4 000 (ms)	Sets balance between original
		beat of BPM time.			sound and echo sound.
3	REVERSE DELAY	Sets delay time of 1/8 to 16/1 per 1	Sets delay time.	10 to 4 000 (ms)	Sets balance between original and
		beat of BPM time.			delay sound.
4	PAN	Sets time of 1/16 to 16/1 per 1 beat of	Sets effect time.	10 to 16 000 (ms)	Sets balance between original
		BPM time for distribution to right/left.			sound and effect sound.
5	TRANS	Sets cut time of 1/16 to 16/1 per 1	Sets effect time.	10 to 16 000 (ms)	Sets balance between original
		beat of BPM time.			sound and effect sound.
6	FILTER	Cycle of cutoff frequency shift is set	Sets cycle for	10 to 32 000 (ms)	Amount of effect increases when
		in unit of 1/4 to 64/1 relative to 1	cutoff time shift.		dial is turned clockwise.
		beat of BPM.
7	FLANGER	Cycle of flanger shift is set in units	Sets cycle for	10 to 32 000 (ms)	Amount of effect increases when
		of 1/4 to 64/1 relative to 1 beat of	flanger effect		dial is turned clockwise. When dial
		BPM.	shift.		is turned fully counterclockwise,
					only original sound is output.
8	PHASER	Cycle of phaser effect shift is set in	Sets cycle for	10 to 32 000 (ms)	Amount of effect increases when
		units of 1/4 to 64/1 relative to 1 beat	phase effect shift.		dial is turned clockwise. When dial
		of BPM.			is turned fully counterclockwise,
					only original sound is output.
9	REVERB (*1)	Amount of reverberation is set from	Sets amount of	1 to 100 (%)	Sets balance between original
		1 to 100 %.	reverberation		sound and effect sound.
			effect.
10 ROBOT		Sets pitch of robot sound effect	Sets pitch of	–100 to +100 (%)	Amount of effect increases when
		within range of –100 to +100 %.	robot sound		dial is turned clockwise.
			effect.
11 CHORUS		Cycle of chorus sound waver is set	Sets cycle of	10 to 32 000 (ms)	Sets balance of chorus sound.
		in units of 1/4 to 64/1 relative to 1	chorus sound
		beat of BPM.	harmonic.
12 ROLL (*2)		Effect time is set as 1/16 to 16/1	Sets effect time.	1 to 4 000 (ms)	Sets balance of original sound and
		relative of 1 beat of BPM.			roll sound.
13 REVERSE ROLL (*2)		Effect time is set as 1/16 to 16/1	Sets effect time.	1 to 4 000 (ms)	Sets balance of original sound and
		relative of 1 beat of BPM.			roll sound.
14 SEND/RETURN		—	—	—	Sets volume of RETURN input
					sound.

(*1) Even if the effect monitor is turned ON, if no sound is output from the channel to the master output, the effect sound will not be heard.

(*2) When effect is disabled (OFF), the effect sound will not be heard, even if monitor is set to effector.

Sound-color effects

	Name	Parameter (COLOR dial)
1	HARMONIC	Sets amount of pitch shift in range of ±6 half-tones. Rotating dial
		to right increases pitch shift by +6 half-tones, while rotating to the
		left reduces pitch shift by –6 half-tones.
2	SWEEP	Sets filter's cutoff frequency. Rotating dial clockwise produces
		band-pass filter effect; rotating counterclockwise produces notch
		filter effect.
3	CRUSH	Sets amount of crushing of input sound. Rotate dial
		counterclockwise to emphasize low-range sounds, and rotate
		clockwise to emphasize high-range sounds.
4	FILTER	Sets cutoff frequency of filter. Rotating dial to right changes high-
		pass filter; rotating dial to left changes low-pass filter.

18

<DRB1392> En