| GAS INSTRUCTIONS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A) | Open base cabinet doors. Bring regulator and hose forward out of cabinet (1). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
B) | Locate hose retention clip (2) on regulator hose. Secure into slot (3) on underside of |
| 1 |
|
|
|
|
|
|
|
| 3 | |||||
| tank scale. |
|
| 2 |
| ||||||||||||
|
|
|
|
|
|
|
|
|
| ||||||||
WARNING: The hose must be secured to the tank scale |
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| with the Hose Retention Clip. Failure to do so could cause |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| damage to the hose resulting in a fire or explosion which |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| can cause serious bodily injury or death, and damage to |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| property. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some LP tanks have differing top collar assembles. (The top collar is the metal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
protective ring around the valve.) One series of tanks mount with the valve facing front |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
(4). The other tanks mount with the valve facing away from the fuel scale (5). Weber |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
recommends the use of cylinder manufacturer’s Manchester and Worthington, with a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
47.6 lb water capacity. Other cylinders may be acceptable for use with the appliance |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
provided they are compatible with the appliance retention means (see illustrations). | 4 |
|
|
|
|
| 5 |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||
The LP cylinder is installed inside the base cabinet, on the tank scale (right side). |
|
|
|
|
|
|
|
|
|
|
|
| |||||
C) | Loosen cylinder lock wing nut. Swing cylinder lock up (6). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
D) | Turn the LP cylinder so the opening of the valve is either to the front or side of the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Weber® gas barbecue. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
E) Lift tank up into position on the tank scale (7). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
F) | Swing the cylinder lock down. Tighten the wing nut. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Connect the Hose to the Cylinder |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A) Remove the plastic dust cover from the valve. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
B) Screw the regulator coupling onto the tank valve, clockwise, or to the right (8). |
| 6 |
|
|
|
|
|
| 6 |
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
Note: This connection tightens clockwise and will not allow gas to flow unless the connection is tight.The connection requires tightening by hand only.
WARNING: Do not use a wrench to tighten the connection.
Using a wrench could damage the regulator coupling and could cause a leak. ◆
7
8
10