A&D AD-4405 manual Exiting the Calibration Mode, Stable

Page 18

Weighing a Mass less than the Maximum Capacity

Step12	Set a mass value using the 0 - 9 keys.
Step13	Place a mass equivalent to the displayed value
	on the weighing unit. Proceed to step 15.

Weighing a Maximum Capacity Mass

Step14 Place a mass equivalent to the maximum capacity on the weighing unit.

Step15 Press the			ENTER	key after the	STABLE
mark turns on. Proceed to step17.
		..........	The key to proceed to step17
	ESC	key	The key to proceed to step17

without changing the span parameters.

Caution: Do not press the ENTER key while the STABLE mark is off (detecting motion). Arrange the condition using the F00 filter function.

Digital Input

Step16 Pressing the +/- key, a stored input voltage parameter of the span is displayed in the unit of mV/V. Adjust the input voltage using

the 0 - 9 keys. (It is possible to store a greater value than the capacity.)

ENTER key...... The key to store the span

parameters and proceed to step 17.

ESC key .......... The key to proceed to step 17

without changing the span parameters.

Span calibration

Maximum capacity

To step 14, step 16

			To step 12
		0	9
	New mass value
	Mass of
	maximum capacity
			step 13
		To step 14	step 14
	To step 16	Place the displayed
	To step 16	mass on the
		mass on the
		weighing unit
		Turn on STABLE mark
			PRINT
			ENTER

NET/GROSS

Stored input voltage

	+/-
	mV/V
0	9

mV/V

PRINT	New input voltage
ENTER

5.2.5.Exiting the Calibration Mode

Step17 Check the Calend display.

Use the following keys.

CAL key ..... To store the parameters and display

Caloff. Proceed to the next step. Caloff could be displayed by pressing the +/- key while pressing the ON/OFF key instead of CAL key.

NET/GROSS

or

+/-

PRINT

ENTER

Turn display off

PRINT

ENTER

5.2. Calibration Procedure

Page 16

AD-4405 Weighing Indicator

Image 18

Contents Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance Compliance with FCC RulesCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input SensitivityInstalling an Option Board Description of Panels and symbols Front Panel DescriptionOther Displays and Symbols Rear Panel DescriptionSupplemental accessories for printer Accessories and optionsStandard accessories OptionsItems of Calibration Mode CalibrationCalibration Procedure Configuring a Weighing InstrumentSpecifying the Resolution, Decimal Point Position and Format Specifying the Range and UnitSpecifying the Weighing Range of the First Range Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Second Range CapacityZero Calibration Span CalibrationExiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization FunctionGravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings FunctionsFunctions OFFZERO+TARE = CAL EXT1 EXT2EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YYPrint Format CF-Functions Weighing Tare Digital Input Preset TareTare Clearing TarePreparation and Specifications AccumulationDisplay and Operation Parameter Using Code Memory Code MemoryWeight Check Mode ComparisonCondition formula for Comparison HI, OKLO, OK Setting the Upper/Lower Limit Values Setting Order and Display for Weight Check ModeMode F22 = 7 Check weighing Setpoint ComparisonDescription of Input parameters and Outputs Output and ConditionStart F22 = 9 Check weighing 3Loss in weightSimple Batch Weighing CompletionSetting the Parameters of Setpoint Comparison Toward the Zero bandReturns to Zero band Display and the Data Output of Hold and Average Setting the Hold FunctionsHold Function Relations to the Other FunctionsTARE, ZERO, SETPOINT, Total Key input and command in the hold stateConditions of the Average and Release MT, MZ, HCUsing the Counting Function Unit Weight RegistrationCounting Function Key to register the unit weight and return to the piece Calendar / Clock 13.1 Time and Date FunctionsYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon15.1 Data Output / Print Mode Common Printer and Data Output ItemsData Number Interval Data Output / PrintSetting the Interval Time Interval Data Output / Print outputCircuit and Pin Connection 16.1 SpecificationsRS-232C Interface Bit FormatData Format FiguresCommand Format Explanation of CommandsCommands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code MemorySet the Unit Weight for Counting Mode Commands to Set ParametersSet the Preset Tare Set the Limit/Setpoint ValueStart Averaging to Hold Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Release the Hold DataUFC Commands UFC Command Parameters’$AN$TL$LF$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF PF2,$DT$TM$LF$AN$SP$TL$LFCOM RS-422/RS-485, Relay OutputOP-03TRM CircuitSwitching Between RS-422/RS-485 Relay Output & Control Input OP-05 DC50VCircuits Specifications Settings19 -20mA Analog Output OP-07 Current Loop Output OP-08 CL1CL2 Current Loop Output Data FormatDigital Section SpecificationsAnalog Input and A/D Conversion InterfaceDimensions GeneralMemo Memo Memo