A&D AD-4405 manual Comparator

Page 28

Comparator

		Item	Parameter	Description
			* 0	Not used
			1	Upper/lower limit comparison (2 Limits setting)
			2	Upper/lower limit comparison (Target and allowance)
			3	Upper/lower limit comparison (Target and % allowance)
			4	HH/Hi/OK/Lo/LL comparison (4 Limits setting)
	f22		5	HH/Hi/OK/Lo/LL comparison (Target and allowance)
	f22		6	HH/Hi/OK/Lo/LL comparison (Target and % allowance)
	Comparator function		6	HH/Hi/OK/Lo/LL comparison (Target and % allowance)
	Comparator function		7	Check weighing 1
			7	Check weighing 1
			8	Check weighing 2
			9	Check weighing 3
			10	Simple batch 1
			11	Simple batch 2
			12	Simple batch 3 (Loss in weight)
	f23 (f22 1 to 6)		10 11	Includes zero band(1)
		[Type2]	20 21	Includes minus(1)	Initial settings are
	Validation of		30 31	Stable(0) /All of the time(1)	11,21,31 and 40.
	comparison		40 41	All of the time(0)/Start, stop(1)
			10 11	Tare when start(1)
	f23 (f22 10 to 12)		20 21	Stop after Full by key(0)/Auto(1)
		[Type2]		Over/Under judgment:	Initial settings are
	Sub function for		30 31	After dribble flow(0) /	11,21,31 and 40.
	batch weighing			Batch finish(1)
			40 41	No function
	f24		* 0	Over	Effective when
	Relay output		1	Under	Effective when
	Relay output		1	Under	f22 7,9,10 or 12.
	selection		2	Finish / Full (f22 9,10,12)	f22 7,9,10 or 12.
	selection		2	Finish / Full (f22 9,10,12)
	f25		00. to	Relay on time by 0.1second step	Initial setting is 00..
	Batch finish output time		99.	(00 : continuous to zero band)	Initial setting is 00..
	Batch finish output time		99.	(00 : continuous to zero band)
	f26		-999999 to 999999		Initial setting is 0.
	Zero band		-999999 to 999999		Initial setting is 0.
	Zero band
	*:	Initial settings.
	Hold
		Item	Parameter	Description
			** 0	Not hold (Hold function is off)
	f27		1	Manual hold
	Hold mode		2	Auto hold
			3	Manual and Auto hold
	f28		00. to	Averaging time by 0.1second step	Initial setting is 00..
	Averaging time		99.	(00 : hold at start time)	Initial setting is 00..
	Averaging time		99.	(00 : hold at start time)
	*:	Initial settings.

6.2. F-Functions

Page 26

AD-4405 Weighing Indicator

Image 28

Contents Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input SensitivityInstalling an Option Board Description of Panels and symbols Front Panel DescriptionOther Displays and Symbols Rear Panel DescriptionAccessories and options Standard accessoriesSupplemental accessories for printer OptionsItems of Calibration Mode CalibrationCalibration Procedure Configuring a Weighing InstrumentSpecifying the Resolution, Decimal Point Position and Format Specifying the Range and UnitSpecifying the Second Range Resolution To Get Stabilized DataSpecifying the Weighing Range of the First Range Specifying the Second Range CapacityZero Calibration Span CalibrationExiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization FunctionGravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings FunctionsFunctions OFFZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YYPrint Format CF-Functions Digital Input Preset Tare TareWeighing Tare Clearing TarePreparation and Specifications AccumulationDisplay and Operation Parameter Using Code Memory Code MemoryWeight Check Mode ComparisonHI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode Setpoint Comparison Description of Input parameters and OutputsF22 = 7 Check weighing Output and ConditionF22 = 9 Check weighing 3Loss in weight Simple BatchStart Weighing CompletionToward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Setting the Hold Functions Hold FunctionDisplay and the Data Output of Hold and Average Relations to the Other FunctionsKey input and command in the hold state Conditions of the Average and ReleaseTARE, ZERO, SETPOINT, Total MT, MZ, HCUnit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon15.1 Data Output / Print Mode Common Printer and Data Output ItemsData Number Interval Data Output / PrintSetting the Interval Time Interval Data Output / Print output16.1 Specifications RS-232C InterfaceCircuit and Pin Connection Bit FormatData Format FiguresCommand Format Explanation of CommandsCommands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code MemoryCommands to Set Parameters Set the Preset TareSet the Unit Weight for Counting Mode Set the Limit/Setpoint ValueCommands for the Hold Function Commands to Set the Data Output/ Print Format UFCStart Averaging to Hold Release the Hold DataUFC Commands UFC Command Parameters$DL SF1,$ID$DN$CR$LF$GR$UT$CR$LF’$AN$TL$LF$LF PF2,$DT$TM$LF$AN$SP$TL$LFRS-422/RS-485, Relay OutputOP-03 TRMCOM CircuitSwitching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Current Loop Output Data FormatSpecifications Analog Input and A/D ConversionDigital Section InterfaceDimensions GeneralMemo Memo Memo