A&D AD-4405 manual Calendar / Clock, Time and Date Functions, Yy/Mm/Dd

Page 50

13. Calendar / Clock

The AD-4405 has a built-in calendar/clock backed up by a lithium battery. The calendar/clock continues to operate with AC power turned off. Leap years are automatically corrected. The time and date can be added to the data output and optional built-in printer output.

 

 

 

13.1.

Time and Date Functions

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Item

 

Parameter

Description

 

 

f50

 

*0

12hours (00-11 AM/PM)

Display, serial data output

 

 

Time display

 

1

24hours (00-23)

and print output

 

 

f51

 

*0

YY/MM/DD

Display, serial data output

 

 

 

1

MM/DD/YY

 

 

Date format

 

and print output

 

 

 

2

DD/MM/YY

 

 

 

 

 

 

 

 

 

f52

 

00 to

(Display/output year) –

Last 2 digits

 

 

Difference between

 

 

 

 

99

(Christian year)

Initial setting is 0.

 

 

Christian year

 

 

 

 

 

 

 

 

 

 

 

 

 

*0

2digits

 

 

 

f53

 

1

4digits (Numeric)

First 2digits specified at

 

 

 

f54.

 

 

Print/output of year

 

 

 

 

 

 

2

4digits (alphabets and year)

Specify alphabet and

 

 

 

 

 

 

 

 

 

 

 

 

format at f54.

 

 

 

 

 

 

 

 

 

 

f54

 

00 to

2digits number (f53 1) or

 

 

 

First 2ditigts of

 

Effective f53 1 or 2

 

 

 

99

alphabet, blank or dot

 

 

year

 

 

 

 

 

 

 

 

 

f52 : The display or output year is calculated using the following formula. Display/output year = (Christian era) + (f52)

Example 1: Christian era = (20)05, f52 10 then display/output year = (20)15

Example 2: Christian era = (20)05, f52 99 then display/output year = (20)04 Keep the internal year in Christian era format because the leap year correction is made based on the Christian era.

f53 and f54 : 2 characters can be added preceding the internal year to the output of the year. Additional characters are set at f54. A 4 digit year can not be displayed.

f53 0 Add no character, output year is 2 characters.

f53 1 Add 2 digit numeric characters. The 2 digits number does not increment automatically if the internal year changes from 99 to 00.

Example: Setting f54 20, internal year (after f52 calculate) = 05, output year = 2005

13. Calendar / Clock

Page 48

AD-4405 Weighing Indicator

Image 50
Contents Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with European Directives ComplianceCompliance with FCC Rules Introduction Load Cell Connections Installation and PrecautionsInstallation and Precautions Adjustment of the Load Cell Output Verifying Load Cell Output and Input SensitivityInstalling an Option Board Description of Panels and symbols Front Panel DescriptionOther Displays and Symbols Rear Panel DescriptionSupplemental accessories for printer Accessories and optionsStandard accessories OptionsItems of Calibration Mode CalibrationCalibration Procedure Configuring a Weighing InstrumentSpecifying the Resolution, Decimal Point Position and Format Specifying the Range and UnitSpecifying the Weighing Range of the First Range Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Second Range CapacityZero Calibration Span CalibrationExiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization FunctionGravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings FunctionsFunctions OFFZERO+TARE = CAL EXT3 EXT1EXT2 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YYPrint Format CF-Functions Weighing Tare Digital Input Preset TareTare Clearing TarePreparation and Specifications AccumulationDisplay and Operation Parameter Using Code Memory Code MemoryWeight Check Mode ComparisonLO, OK Condition formula for ComparisonHI, OK Mode Setting the Upper/Lower Limit ValuesSetting Order and Display for Weight Check Mode F22 = 7 Check weighing Setpoint ComparisonDescription of Input parameters and Outputs Output and ConditionStart F22 = 9 Check weighing 3Loss in weightSimple Batch Weighing CompletionReturns to Zero band Setting the Parameters of Setpoint ComparisonToward the Zero band Display and the Data Output of Hold and Average Setting the Hold FunctionsHold Function Relations to the Other FunctionsTARE, ZERO, SETPOINT, Total Key input and command in the hold stateConditions of the Average and Release MT, MZ, HCCounting Function Using the Counting FunctionUnit Weight Registration Key to register the unit weight and return to the piece YY/MM/DD Calendar / Clock13.1 Time and Date Functions Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon15.1 Data Output / Print Mode Common Printer and Data Output ItemsData Number Interval Data Output / PrintSetting the Interval Time Interval Data Output / Print outputCircuit and Pin Connection 16.1 SpecificationsRS-232C Interface Bit FormatData Format FiguresCommand Format Explanation of CommandsCommands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code MemorySet the Unit Weight for Counting Mode Commands to Set ParametersSet the Preset Tare Set the Limit/Setpoint ValueStart Averaging to Hold Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Release the Hold DataUFC Commands UFC Command Parameters’$AN$TL$LF$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF PF2,$DT$TM$LF$AN$SP$TL$LFCOM RS-422/RS-485, Relay OutputOP-03TRM CircuitSwitching Between RS-422/RS-485 Circuits Relay Output & Control Input OP-05DC50V 19 -20mA Analog Output OP-07 SpecificationsSettings CL2 Current Loop Output OP-08CL1 Current Loop Output Data FormatDigital Section SpecificationsAnalog Input and A/D Conversion InterfaceDimensions GeneralMemo Memo Memo