A&D AD-4405 manual CF-Functions

Page 34

6.3. CF-Functions

Item

Parameter

Description

Cf00

* 0

No limitation

Zero tracking width,

motion detection

1

Use limitation at F01, F02, F03, F27 and F28.

condition

Cf01

* 0

2% of CAP,

Tare limit is 100 % CAP

Zero range

1

10% of CAP,

Tare limit is 100 % CAP

Turning display on, the

2

3% of CAP,

Tare limit is 50 % CAP

range to zero display.

3

4% of CAP,

Tare limit is 50 % CAP

Cf02

0

Not to zero when turning the display on.

Power on zero range

* 1

10% of CAP

Turning the display on,

2

3% of CAP

the range to zero display.

3

4% of CAP

Cf03

0

Gross when displaying gross.

1

Gross

Zero tracking

* 2

Gross or Net when displaying net.

Cf04

TARE, ZERO in motion / TARE at negative gross

* 0

Not accepted

/

Not accepted

TARE, ZERO in motion /

1

Execute

/

Not accepted

TARE at negative gross

2

Not accepted

/

Execute

value

3

Execute

/

Execute

Cf05

* 0

Not to output data at unstable value or overload.

Output on overload and

Effective in key mode.

unstable state.

1

To output data always.

GROSS / NET / TARE / Preset TARE

Cf06

* 0

GR

/

NT

/

TR

/

TR

Header 2

1

GR

/

NT

/

TR

/

PT

2

G_

/

N_

/

T_

/

PT

(_: Space 20h)

Cf07

* 0

Two digits

Serial output data

Number of unit digits

1

Three digits

Cf08

* 0

Not used (Ineffective)

Accumulation function

1

Used

(Effective)

Cf09

* 0

Used

(Effective)

Digital Tare(PT)

1

Not used (Ineffective)

CAP : maximum capacity

*: Initial settings

Power on ZERO (CF02)

Cf02	0	After power on, the weight display starts immediately.

Cf02	1,2,3	When the zero range is exceeded at power on,			------

		Press the	ESC	key to start the weight display.

is displayed.

6.3. CF-Functions

Page 32

AD-4405 Weighing Indicator

Image 34

Contents Weighing Indicator This manual and Marks Contents Setting the Parameters of Setpoint Comparison Compliance with FCC Rules ComplianceCompliance with European Directives Introduction Installation and Precautions Installation and PrecautionsLoad Cell Connections Adjustment of the Load Cell Output Verifying Load Cell Output and Input SensitivityInstalling an Option Board Description of Panels and symbols Front Panel DescriptionOther Displays and Symbols Rear Panel DescriptionSupplemental accessories for printer Accessories and optionsStandard accessories OptionsItems of Calibration Mode CalibrationCalibration Procedure Configuring a Weighing InstrumentSpecifying the Resolution, Decimal Point Position and Format Specifying the Range and UnitSpecifying the Weighing Range of the First Range Specifying the Second Range ResolutionTo Get Stabilized Data Specifying the Second Range CapacityZero Calibration Span CalibrationExiting the Calibration Mode Weighing Range Function Setting the Division and Range Digital Linearization FunctionGravity Compensation Function Gravity Acceleration Table Calibration Error Code List Changing the Function Settings FunctionsFunctions OFFZERO+TARE = CAL EXT2 EXT1EXT3 Comparator Data Output Current Loop Output Serial Interface YY/MM/DD MM/DD/YY DD/MM/YYPrint Format CF-Functions Weighing Tare Digital Input Preset TareTare Clearing TarePreparation and Specifications AccumulationDisplay and Operation Parameter Using Code Memory Code MemoryWeight Check Mode ComparisonHI, OK Condition formula for ComparisonLO, OK Setting Order and Display for Weight Check Mode Setting the Upper/Lower Limit ValuesMode F22 = 7 Check weighing Setpoint ComparisonDescription of Input parameters and Outputs Output and ConditionStart F22 = 9 Check weighing 3Loss in weightSimple Batch Weighing CompletionToward the Zero band Setting the Parameters of Setpoint ComparisonReturns to Zero band Display and the Data Output of Hold and Average Setting the Hold FunctionsHold Function Relations to the Other FunctionsTARE, ZERO, SETPOINT, Total Key input and command in the hold stateConditions of the Average and Release MT, MZ, HCUnit Weight Registration Using the Counting FunctionCounting Function Key to register the unit weight and return to the piece 13.1 Time and Date Functions Calendar / ClockYY/MM/DD Setting Time and Date Corrected date is as follows 05 05 Internal Printer OP-06 Installing the Printer Paper Special roll paper Replacing the Ink Ribbon15.1 Data Output / Print Mode Common Printer and Data Output ItemsData Number Interval Data Output / PrintSetting the Interval Time Interval Data Output / Print outputCircuit and Pin Connection 16.1 SpecificationsRS-232C Interface Bit FormatData Format FiguresCommand Format Explanation of CommandsCommands to Request Data Commands to Control the Indicator Changing the Weight Unit Changing the Code MemorySet the Unit Weight for Counting Mode Commands to Set ParametersSet the Preset Tare Set the Limit/Setpoint ValueStart Averaging to Hold Commands for the Hold FunctionCommands to Set the Data Output/ Print Format UFC Release the Hold DataUFC Commands UFC Command Parameters’$AN$TL$LF$LF $DLSF1,$ID$DN$CR$LF$GR$UT$CR$LF PF2,$DT$TM$LF$AN$SP$TL$LFCOM RS-422/RS-485, Relay OutputOP-03TRM CircuitSwitching Between RS-422/RS-485 DC50V Relay Output & Control Input OP-05Circuits Settings Specifications19 -20mA Analog Output OP-07 CL1 Current Loop Output OP-08CL2 Current Loop Output Data FormatDigital Section SpecificationsAnalog Input and A/D Conversion InterfaceDimensions GeneralMemo Memo Memo