Graco 332305B Programming the Max Model, Powering Units With Controllers, Entering Setup Mode

Page 29

Programming the Max Model

Powering Units With Controllers

By default, units with controllers are set to operate in a timed mode with 1 minute of ON time and 8 hours of OFF time. The unit should be powered up in OFF mode,

counting down from the 8 hours. If the unit powers up in ON mode and has not been primed, hold the reset but- ton located on the control panel (example shown on the right) for 1 second to move to the OFF mode.

NOTE:

•A blinking number on the display indicates the G3 is in SETUP MODE.

•In RUN MODE numbers on the display do not blink.

•After 60 seconds of no activity, the device returns to RUN MODE in the OFF Time cycle and the OFF Time restarts counting down the total programmed amount of time. It does not resume the countdown from the point where the cycle was interrupted when you entered SETUP MODE.

Entering Setup Mode

Press both the UP and DOWN ARROW buttons together for 3 seconds to enter the SETUP MODE.

NOTE: If the lock LED is lit after entering Setup Mode and four 0000’s are displayed, the unit has a PIN Code lock out enabled. See the follow- ing section: Entering a PIN Code to Access Setup Mode.

Entering a PIN Code to Access Setup Mode

The G3 controller does not require a user to provide a PIN code to access the programming features of the unit. However, Graco understands that some users may want to protect the programming settings and therefore, an option for adding PIN Code authorization is available. The instructions for setting up PIN Code Authorization are provided in the Advanced Programming section of this manual. See page 46.

To enter the PIN Code:

Max Model Setup

1.Press both the UP and DOWN ARROW buttons for 3 seconds.

2.The LED next to the LOCK ICON on

the display lights and the 4 zeros appear on the display indicating the

system requires a PIN Code entry to run the G3 in

SETUP MODE.

3.The cursor is automatically positioned to enter the first character of the PIN Code. Use the UP and DOWN ARROW buttons to move up

and down through the numbers 0-9 until the first number in the PIN code is displayed in the field.

4.Press the ENTER button to set the num- ber. The cursor automatically moves to the next number field.

5.Repeat steps 3 and 4 for each PIN Code prompt field.

If the PIN Code you entered is correct, the first editable character on the display will flash.

NOTE: A blinking field on the display indicates the G3 is in SETUP MODE. In RUN MODE numbers on the dis- play will not blink.

332305B

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents G3 Max Automatic Lubrication Pump Important Safety InstructionsContents Part Model Numbers Part / Model NumbersLiter Models G3-G-ACMX-8L0L00-1DMVA2R3 Understanding the Model Number Electric Shock Hazard Skin Injection Hazard Grounding InstallationComponent Identification KeyDivider Installations Injector Installations Typical InstallationAutomatic System Activation Hazard Choosing an Installation LocationRecommendations for Using Pump in Harsh Environments System Configuration and WiringFuses Input Voltage Fuse Value Graco Kit NoAlarm Relay Response Alarm Output and Remote Illumination Response571032 Wiring and Installation DiagramsKits 571030 Connector on Housing Power DIN AC 15 foot Part No U790Connector on Cable Example Wiring DiagramConnector on Housing Power DIN DC 15 foot Part No U790Connector on Cable Example Wiring DiagramPower CPC DC -15 foot Part No Manual Orange Power CPC DC 5 WireInputs M12 Dry Contacts Sink NPN 2 or 3 wire Source PNP 2 or 3 wireVent Valve Outputs Alarm Outputs Part No Field Wireable Pin Out M12 Wire Colors Part No Cable Pin Out M12 Wire ColorsInstallation Connecting to Auxiliary Fittings SetupPressure Relief Pressure Relief ValvesOutput Volume / Minute Setting Pump Outlet VolumeLoading Grease No. Spacers Cubic inches Cubic cmChanging Greases Models without a follower platePriming Filling Oil UnitQuick Setup Guide Control Panel Overview FIG Max Model SetupEntering Setup Mode Powering Units With ControllersEntering a PIN Code to Access Setup Mode Programming the Max ModelEnter the Year Setting the Real Time ClockProgramming on Duration Cycle C1, C2, C3 SetupInput Not Used Pressure Control P1, P2, P3 SetupBackup Time Programming on Time Programming Backup TimeOn Time Machine Count Pump OFF / Rest SetupBackup Time Setup Programming OFF Time OFF TimePrelube Prelube DelaySetting Prelube Uploading Pump Program Settings to the Pump Storing Pump Program Settings to the Flash DriveDMS Models Only Downloading DataViewing the Unit DMS ID Number Sample System Event Log Operation / Data LogSystem Event Log Sample Error Log Error LogCommon Error Log entries are listed below Sample Functional Summary Functional SummaryCommon Functional Summary Data entries are listed below Sample Technical Summary Technical SummaryPIN Advanced ProgrammingSelecting Advanced Setup Options Entering Advanced SetupA1 Setting Up PIN Code Entering a PIN Code for the First TimeA3 Vent Valve Time A2 Low Level Alarm TimeTo set Vent Valve Time Alarm RetryTo set the Alarm Retry Active Alarm On OFF MM SS HH MM Constant Alarm Output on FaultTime Control Run ModePressure Control Lubrication Mode Pump on ControlsCycle Control Rest Mode Pump OFF Controls Backup TimeOFF Time Machine CountVenting Prelube / Prelube DelayAdditional Controls Manual Run Cycle Fault / Warning Scenarios AlarmsCycle Pressure Low Level FaultMachine Count Fault Cycle Pressure FaultMotor Cur SystemRent Warn IngTure Warning USB ErrorTempera Problem Cause Solution TroubleshootingProblem Cause Solution Frequency Component Required Maintenance MaintenanceParts 2 Liter Models Parts 4 Liter and Larger Models Part Description Qty PartsPart Description Qty Part Description Qty 96G124, 96G175, 96G176, 96G186 96G188 Is not intended as a way to Relieve pressure during normal Installation and Repair KitsTechnical Data Model Height Width Depth Inches DimensionsOption Mounting Pattern332305B Graco Information Graco Standard Warranty
Top Page Image Contents