Graco 332305B important safety instructions Programming OFF Time

Page 35

•An LED flashes under

either HH when pro-

 

gramming hours OR

 

MM when program-

OR

ming minutes.

 

•In SETUP MODE the

number displayed in the first field, on the

left side of display blinks, indicating the device is ready to pro- gram the Backup Time hours.

•The total amount of Backup Time must

be at least twice as long as the pro- grammed ON Time. If a value less than twice the ON Time is entered, the

RED alarm LED lights and the value must be updated.

If this time does not meet the application needs, contact Graco Customer Support.

Programming Backup Time

NOTE: When programming a Backup Time of less than 10 hours you must program a leading zero in the first number field and press the ENTER button to save the zero selection.

1.To set the Backup Time use the UP or DOWN ARROW button to scroll through numerals 0 to 9 until the desired number appears in the first HH (hour) field.

2.Press the ENTER button to lock in the selection. The next HH number field to the right flashes indicating it is ready for programming.

3.Use the UP or DOWN ARROW button to scroll through numerals 0 to 9 until the desired number appears in the second HH number field.

4.Press the ENTER button to lock in the selection.

The next number field to the right

flashes and the LED lights under MM; indicating it is ready to program the minutes fields.

Max Model Setup

5.Repeat steps 1 - 4 to set the next MM (minutes) fields.

6.After pressing the ENTER button to set the last MM field, the OFF Time informa- tion is saved.

7.After selecting ON, refer to page 32.

NOTE: Backup time can be set in HH:MM for the machine count input.

OFF Time

•The LED next to the clock in the OFF field lights, indicating you are setting the OFF Time parameters.

•OFF Time is set in Hours and Minutes (HH: MM).

•An LED flashes under

either HH when pro-

 

gramming hours OR

 

MM when program-

OR

ming minutes.

 

•In SETUP MODE the

number displayed in the first field, on the left side of display blinks, indicating the device is ready to pro- gram the OFF Time hours.

•The total amount of OFF Time must be

at least twice as long as the pro- grammed ON Time. If a value less than twice the ON Time is entered, the

RED alarm LED lights and the value must be updated.

If this time does not meet the application needs, contact Graco Customer Support.

Programming OFF Time

NOTE: When programming a time of less than 10 hours you must program a leading zero in the first number field and press the ENTER button to save the zero selection.

332305B

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents G3 Max Automatic Lubrication Pump Important Safety InstructionsContents Part Model Numbers Part / Model NumbersLiter Models G3-G-ACMX-8L0L00-1DMVA2R3 Understanding the Model Number Electric Shock Hazard Skin Injection Hazard Key InstallationGrounding Component IdentificationDivider Installations Injector Installations Typical InstallationAutomatic System Activation Hazard Choosing an Installation LocationInput Voltage Fuse Value Graco Kit No System Configuration and WiringRecommendations for Using Pump in Harsh Environments FusesAlarm Relay Response Alarm Output and Remote Illumination Response571032 Wiring and Installation DiagramsKits 571030 Example Wiring Diagram Power DIN AC 15 foot Part No U790Connector on Housing Connector on CableExample Wiring Diagram Power DIN DC 15 foot Part No U790Connector on Housing Connector on CablePower CPC DC -15 foot Part No Manual Orange Power CPC DC 5 WireInputs M12 Dry Contacts Sink NPN 2 or 3 wire Source PNP 2 or 3 wireVent Valve Outputs Alarm Outputs Part No Field Wireable Pin Out M12 Wire Colors Part No Cable Pin Out M12 Wire ColorsInstallation Pressure Relief Valves SetupConnecting to Auxiliary Fittings Pressure ReliefNo. Spacers Cubic inches Cubic cm Setting Pump Outlet VolumeOutput Volume / Minute Loading GreaseChanging Greases Models without a follower platePriming Filling Oil UnitQuick Setup Guide Control Panel Overview FIG Max Model SetupProgramming the Max Model Powering Units With ControllersEntering Setup Mode Entering a PIN Code to Access Setup ModeEnter the Year Setting the Real Time ClockProgramming on Duration Cycle C1, C2, C3 SetupInput Not Used Pressure Control P1, P2, P3 SetupBackup Time Programming on Time Programming Backup TimeOn Time Machine Count Pump OFF / Rest SetupBackup Time Setup Programming OFF Time OFF TimePrelube Prelube DelaySetting Prelube Downloading Data Storing Pump Program Settings to the Flash DriveUploading Pump Program Settings to the Pump DMS Models OnlyViewing the Unit DMS ID Number Sample System Event Log Operation / Data LogSystem Event Log Sample Error Log Error LogCommon Error Log entries are listed below Sample Functional Summary Functional SummaryCommon Functional Summary Data entries are listed below Sample Technical Summary Technical SummaryPIN Advanced ProgrammingEntering a PIN Code for the First Time Entering Advanced SetupSelecting Advanced Setup Options A1 Setting Up PIN CodeA3 Vent Valve Time A2 Low Level Alarm TimeTo set Vent Valve Time Alarm RetryTo set the Alarm Retry Active Alarm On OFF MM SS HH MM Constant Alarm Output on FaultTime Control Run ModePressure Control Lubrication Mode Pump on ControlsCycle Control Rest Mode Pump OFF Controls Backup TimeOFF Time Machine CountVenting Prelube / Prelube DelayAdditional Controls Manual Run Cycle Fault / Warning Scenarios AlarmsCycle Pressure Low Level FaultMachine Count Fault Cycle Pressure FaultIng SystemMotor Cur Rent WarnTure Warning USB ErrorTempera Problem Cause Solution TroubleshootingProblem Cause Solution Frequency Component Required Maintenance MaintenanceParts 2 Liter Models Parts 4 Liter and Larger Models Part Description Qty PartsPart Description Qty Part Description Qty 96G124, 96G175, 96G176, 96G186 96G188 Is not intended as a way to Relieve pressure during normal Installation and Repair KitsTechnical Data Model Height Width Depth Inches DimensionsOption Mounting Pattern332305B Graco Information Graco Standard Warranty
Top Page Image Contents