Graco 332305B important safety instructions Advanced Programming, Pin

Page 45

Advanced Programming

Advanced Programming

There are 7 Advanced Programming options. The following Table Identifies each option and when it is used.

	Advanced	Model	Setting	Format/ Description	Why Use This?
	Option	Model	Setting	Format/ Description	Why Use This?
	Option

	A1	Max	Lockout	Secures setup modes with	Prevents unauthorized users to adjusting
			Code	PIN	settings.
			(Optional)
	A2	Max	Low Level	MM:SS (minutes:seconds)	To accommodate most lubrication situa-
			Alarm Time	sets amount of time	tions, a conservative amount of time is pro-
				between Low Level Warning	grammed between the low level warning
				to Low Level Fault.	and fault to help protect unit from running
				Default = 3 minutes	dry. If necessary the amount of time the
					unit runs before stopping due to a low level
					fault can be adjusted.
	A3	Max	Vent Valve	MM:SS (minutes:seconds)	• In an injector based system that does not
			Time	sets amount of time vent	use a sensor for feedback, determines
				valve stays open after Pump	the amount of time the system vents.
				ON Mode.	• Vent time can be modified.
				Default = 5 minutes
	A4	Max	Alarm Retry	Sets number of automatic	Establishes the number of times the unit
				retries after a Cycle or Pres-	automatically retries lubricating after a
				sure Alarm.	cycle or pressure alarm to determine if a
				Default = 0	temporary or false signal can be cleared.
				Default = 0
	A5	Max	Active	Changes alarm output	Uses alarm output to determine if a unit has
			Alarm	behavior.	an alarm AND/OR loses power.
				Default = OFF	The output turns ON when power is
					applied. It turns OFF when power is lost or
					an alarm occurs.
					Normal operation (OFF) will only activate
					alarm output in an alarm condition when
					power is on.
					Can change (set to ON) to activate alarm
					with power ON and deactivate with power
					OFF OR warning.
					Used to manage power outage.
	A6	DMS™	Functional	Clears the Functional and	Allows user to track lube events from a spe-
		Equipped	and Techni-	Technical User Summaries	cific point (reset), i.e. a month to month
		Models	cal User		evaluation.
			Summary
			Reset
	A7	Max	Constant	Changes alarm output	This function changes the behavior of the
			Alarm Out-	behavior.	alarm output in a fault from either toggling
			put on Fault	Default = OFF	once every second or steady on.
				Default = OFF

332305B

45

Image 45

Contents G3 Max Automatic Lubrication Pump Important Safety InstructionsContents Part / Model Numbers Liter ModelsPart Model Numbers G3-G-ACMX-8L0L00-1DMVA2R3 Understanding the Model Number Electric Shock Hazard Skin Injection Hazard Grounding InstallationComponent Identification KeyDivider Installations Injector Installations Typical InstallationAutomatic System Activation Hazard Choosing an Installation LocationRecommendations for Using Pump in Harsh Environments System Configuration and WiringFuses Input Voltage Fuse Value Graco Kit NoAlarm Relay Response Alarm Output and Remote Illumination ResponseWiring and Installation Diagrams Kits 571030571032 Connector on Housing Power DIN AC 15 foot Part No U790Connector on Cable Example Wiring DiagramConnector on Housing Power DIN DC 15 foot Part No U790Connector on Cable Example Wiring DiagramPower CPC DC -15 foot Part No Manual Orange Power CPC DC 5 WireInputs M12 Dry Contacts Sink NPN 2 or 3 wire Source PNP 2 or 3 wireVent Valve Outputs Alarm Outputs Part No Field Wireable Pin Out M12 Wire Colors Part No Cable Pin Out M12 Wire ColorsInstallation Connecting to Auxiliary Fittings SetupPressure Relief Pressure Relief ValvesOutput Volume / Minute Setting Pump Outlet VolumeLoading Grease No. Spacers Cubic inches Cubic cmChanging Greases Models without a follower platePriming Filling Oil UnitQuick Setup Guide Control Panel Overview FIG Max Model SetupEntering Setup Mode Powering Units With ControllersEntering a PIN Code to Access Setup Mode Programming the Max ModelEnter the Year Setting the Real Time ClockProgramming on Duration Cycle C1, C2, C3 SetupPressure Control P1, P2, P3 Setup Backup TimeInput Not Used Programming Backup Time On TimeProgramming on Time Pump OFF / Rest Setup Backup Time SetupMachine Count Programming OFF Time OFF TimePrelube Delay Setting PrelubePrelube Uploading Pump Program Settings to the Pump Storing Pump Program Settings to the Flash DriveDMS Models Only Downloading DataViewing the Unit DMS ID Number Operation / Data Log System Event LogSample System Event Log Sample Error Log Error LogCommon Error Log entries are listed below Sample Functional Summary Functional SummaryCommon Functional Summary Data entries are listed below Sample Technical Summary Technical SummaryPIN Advanced ProgrammingSelecting Advanced Setup Options Entering Advanced SetupA1 Setting Up PIN Code Entering a PIN Code for the First TimeA3 Vent Valve Time A2 Low Level Alarm TimeAlarm Retry To set the Alarm RetryTo set Vent Valve Time Active Alarm On OFF MM SS HH MM Constant Alarm Output on FaultTime Control Run ModeLubrication Mode Pump on Controls Cycle ControlPressure Control Rest Mode Pump OFF Controls Backup TimeOFF Time Machine CountPrelube / Prelube Delay Additional ControlsVenting Manual Run Cycle Fault / Warning Scenarios AlarmsCycle Pressure Low Level FaultMachine Count Fault Cycle Pressure FaultMotor Cur SystemRent Warn IngUSB Error TemperaTure Warning Problem Cause Solution TroubleshootingProblem Cause Solution Frequency Component Required Maintenance MaintenanceParts 2 Liter Models Parts 4 Liter and Larger Models Part Description Qty PartsPart Description Qty Part Description Qty 96G124, 96G175, 96G176, 96G186 96G188 Is not intended as a way to Relieve pressure during normal Installation and Repair KitsTechnical Data Model Height Width Depth Inches DimensionsOption Mounting Pattern332305B Graco Information Graco Standard Warranty