Graco 332305B important safety instructions Max Model Setup, Control Panel Overview FIG

Page 28

Max Model Setup

Max Model Setup

Control Panel Overview (FIG. 22)

NOTE: Programming instructions begin on page 29.

OFF TIME/BACKUP TIME

ON TIME/BACKUP TIME

•LED lights when ON Time/Backup Time is running.

•Display shows time as MM:SS (minutes and seconds).

i.e., 08:30 is 8 minutes: 30 sec- onds.

•Sets the limits for the amount of time to complete a cycle or build up pressure before a warning is activated.

•Counts down from a set time to zero.

CYCLE / PRESSURE SETUP

•Sets either Cycle (C) or Pressure

(P) Monitoring limits for up to 3 sensors.

•Each sensor is set up and con- trolled independently.

MACHINE COUNT

•LED lights when Machine Count is used to control Pump OFF function.

•Counts independent machine operations with a sensor to con- trol Pump Off duration.

•Time OFF function can be used as a backup for Machine Count.

LEFT DIRECTION ARROW / RESET

•In ADVANCED and SETUP MODES, moves cursor in dis- play one field to the left.

•In RUN MODE: single press clears warning.

•In ALARM MODE: pressing and holding for 3 seconds clears fault / warning and switches cycle to OFF MODE.

DISPLAY

• A blinking LED under HH, MM, SS or ## identifies type of measurement unit you are setting; i.e., HH is hours.

•A blinking number on the display indicates the G3 is in SETUP MODE.

•In RUN MODE displayed numbers count up or down. See Time ON and Time OFF.

UP and DOWN ARROW

•Hold both the UP and DOWN ARROW but- tons down together for 3 seconds to enter

SETUP MODE.

•In SETUP MODE, increases or decreases number values shown in display.

•LED lights when OFF Time/Backup Time is used to con- trol Pump OFF function.

•Value is entered in HH:M.

•Displays in HH:MM (hours and minutes) when > 1 hour.

•Times pump rest between cycles.

•Counts down from set time to zero.

•Can be set up to use as a backup

for Machine Count control.

ALARM ICONS

LED next to icon lights when a fault / warning event occurs during a run cycle. See page 57 for a complete description of these alarm scenarios.

PIN ICON

• LED next to icon lights indi- cating PIN is required to enter setup.

• In SETUP MODE LED lights when setting up the PIN.

PRELUBE

LED next to icon lights indicat- ing LED lights when Prelube function is enabled.

RIGHT DIRECTION ARROW / MANUAL RUN / ENTER

•In SETUP MODE, saves entry, moves cursor in display one field to the right or to the next setup step.

•In RUN MODE starts a man- ual run cycle.

FIG. 22

28

332305B

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Important Safety Instructions G3 Max Automatic Lubrication PumpContents Liter Models Part / Model NumbersPart Model Numbers G3-G-ACMX-8L0L00-1DMVA2R3 Understanding the Model Number Electric Shock Hazard Skin Injection Hazard Installation GroundingComponent Identification KeyTypical Installation Divider Installations Injector InstallationsChoosing an Installation Location Automatic System Activation HazardSystem Configuration and Wiring Recommendations for Using Pump in Harsh EnvironmentsFuses Input Voltage Fuse Value Graco Kit NoAlarm Output and Remote Illumination Response Alarm Relay ResponseKits 571030 Wiring and Installation Diagrams571032 Power DIN AC 15 foot Part No U790 Connector on HousingConnector on Cable Example Wiring DiagramPower DIN DC 15 foot Part No U790 Connector on HousingConnector on Cable Example Wiring DiagramPower CPC DC -15 foot Part No Power CPC DC 5 Wire Manual OrangeDry Contacts Sink NPN 2 or 3 wire Source PNP 2 or 3 wire Inputs M12Vent Valve Outputs Alarm Outputs Part No Cable Pin Out M12 Wire Colors Part No Field Wireable Pin Out M12 Wire ColorsInstallation Setup Connecting to Auxiliary FittingsPressure Relief Pressure Relief ValvesSetting Pump Outlet Volume Output Volume / MinuteLoading Grease No. Spacers Cubic inches Cubic cmModels without a follower plate Changing GreasesFilling Oil Unit PrimingQuick Setup Guide Max Model Setup Control Panel Overview FIGPowering Units With Controllers Entering Setup ModeEntering a PIN Code to Access Setup Mode Programming the Max ModelSetting the Real Time Clock Enter the YearCycle C1, C2, C3 Setup Programming on DurationBackup Time Pressure Control P1, P2, P3 SetupInput Not Used On Time Programming Backup TimeProgramming on Time Backup Time Setup Pump OFF / Rest SetupMachine Count OFF Time Programming OFF TimeSetting Prelube Prelube DelayPrelube Storing Pump Program Settings to the Flash Drive Uploading Pump Program Settings to the PumpDMS Models Only Downloading DataViewing the Unit DMS ID Number System Event Log Operation / Data LogSample System Event Log Error Log Sample Error LogCommon Error Log entries are listed below Functional Summary Sample Functional SummaryCommon Functional Summary Data entries are listed below Technical Summary Sample Technical SummaryAdvanced Programming PINEntering Advanced Setup Selecting Advanced Setup OptionsA1 Setting Up PIN Code Entering a PIN Code for the First TimeA2 Low Level Alarm Time A3 Vent Valve TimeTo set the Alarm Retry Alarm RetryTo set Vent Valve Time Active Alarm Constant Alarm Output on Fault On OFF MM SS HH MMRun Mode Time ControlCycle Control Lubrication Mode Pump on ControlsPressure Control Backup Time Rest Mode Pump OFF ControlsMachine Count OFF TimeAdditional Controls Prelube / Prelube DelayVenting Manual Run Cycle Alarms Fault / Warning ScenariosLow Level Fault Cycle PressureCycle Pressure Fault Machine Count FaultSystem Motor CurRent Warn IngTempera USB ErrorTure Warning Troubleshooting Problem Cause SolutionProblem Cause Solution Maintenance Frequency Component Required MaintenanceParts 2 Liter Models Parts 4 Liter and Larger Models Parts Part Description QtyPart Description Qty Part Description Qty 96G124, 96G175, 96G176, 96G186 96G188 Installation and Repair Kits Is not intended as a way to Relieve pressure during normalTechnical Data Dimensions Model Height Width Depth InchesMounting Pattern Option332305B Graco Standard Warranty Graco Information
Top Page Image Contents