Graco 332305B DMS Models Only, Storing Pump Program Settings to the Flash Drive, Downloading Data

Page 37

flashes and the LED lights under SS; indicating it is ready to program the seconds fields.

5.Repeat steps 1 - 4 to set the SS (seconds) fields.

6.After pressing the ENTER button to set the last SS field the G3 automatically switches to the RUN MODE.

DMS™ Models Only

Downloading Data

1. Plug the USB flash drive into the USB port.

NOTE: The G3 pump stops pumping as soon as the USB flash drive is plugged into it.

2.The system automatically begins downloading data to the USB drive.

3.“data” is displayed while the system

is downloading files.

4. When download is finished, “done” is displayed.

5.G3 pump restarts cycle in the OFF mode.

6.Remove the USB flash drive.

Storing Pump Program Settings to the Flash Drive

The pump program settings file is named:

GRACO/G3Config/g3config.bin. This file cannot be modified. Modification of the file or file name may cause it to be unusable.

1. Plug the USB flash drive into the USB port.

NOTE: The G3 pump stops pumping as soon as the USB flash drive is plugged into it.

2.The system automatically begins downloading data to the USB drive.

3.“data” is displayed while the system

is downloading files.

4. When download is finished, “done” is displayed.

Max Model Setup

5.G3 pump restarts cycle in the OFF mode.

6.After the download is com- plete, press and hold the UP and DOWN ARROW button for 3 seconds to store the cur- rent setup to the USB flash drive.

7.“data” is displayed while the unit is downloading and storing the configu- ration on the USB drive.

8.When configuration is stored, “done”

is displayed.

9.G3 pump restarts cycle in the OFF mode.

10.Remove the USB flash drive.

Uploading Pump Program Settings to the Pump

1. Plug the USB flash drive into the USB port.

NOTE:

•The USB flash drive must contain file GRACO/G3Config/g3config.bin.

•The G3 pump stops pumping as soon as the USB flash drive is plugged into it.

2.The system automatically begins downloading data to the USB drive.

3.“data” is displayed while the system

is downloading files.

4. When download is finished, “done” is displayed.

5.G3 pump restarts cycle in the OFF mode.

6.After the download is com- plete, press and hold the RESET button and UP ARROW button for 3 seconds

to upload the setup stored in the USB flash drive.

7.“data” is displayed while the unit is

uploading the configuration data.

8. When upload is finished, “done” is displayed.

332305B

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents G3 Max Automatic Lubrication Pump Important Safety InstructionsContents Liter Models Part / Model NumbersPart Model Numbers G3-G-ACMX-8L0L00-1DMVA2R3 Understanding the Model Number Electric Shock Hazard Skin Injection Hazard Grounding InstallationComponent Identification KeyDivider Installations Injector Installations Typical InstallationAutomatic System Activation Hazard Choosing an Installation LocationRecommendations for Using Pump in Harsh Environments System Configuration and WiringFuses Input Voltage Fuse Value Graco Kit NoAlarm Relay Response Alarm Output and Remote Illumination ResponseKits 571030 Wiring and Installation Diagrams571032 Connector on Housing Power DIN AC 15 foot Part No U790Connector on Cable Example Wiring DiagramConnector on Housing Power DIN DC 15 foot Part No U790Connector on Cable Example Wiring DiagramPower CPC DC -15 foot Part No Manual Orange Power CPC DC 5 WireInputs M12 Dry Contacts Sink NPN 2 or 3 wire Source PNP 2 or 3 wireVent Valve Outputs Alarm Outputs Part No Field Wireable Pin Out M12 Wire Colors Part No Cable Pin Out M12 Wire ColorsInstallation Connecting to Auxiliary Fittings SetupPressure Relief Pressure Relief ValvesOutput Volume / Minute Setting Pump Outlet VolumeLoading Grease No. Spacers Cubic inches Cubic cmChanging Greases Models without a follower platePriming Filling Oil UnitQuick Setup Guide Control Panel Overview FIG Max Model SetupEntering Setup Mode Powering Units With ControllersEntering a PIN Code to Access Setup Mode Programming the Max ModelEnter the Year Setting the Real Time ClockProgramming on Duration Cycle C1, C2, C3 SetupBackup Time Pressure Control P1, P2, P3 SetupInput Not Used On Time Programming Backup TimeProgramming on Time Backup Time Setup Pump OFF / Rest SetupMachine Count Programming OFF Time OFF TimeSetting Prelube Prelube DelayPrelube Uploading Pump Program Settings to the Pump Storing Pump Program Settings to the Flash DriveDMS Models Only Downloading DataViewing the Unit DMS ID Number System Event Log Operation / Data LogSample System Event Log Sample Error Log Error LogCommon Error Log entries are listed below Sample Functional Summary Functional SummaryCommon Functional Summary Data entries are listed below Sample Technical Summary Technical SummaryPIN Advanced ProgrammingSelecting Advanced Setup Options Entering Advanced SetupA1 Setting Up PIN Code Entering a PIN Code for the First TimeA3 Vent Valve Time A2 Low Level Alarm TimeTo set the Alarm Retry Alarm RetryTo set Vent Valve Time Active Alarm On OFF MM SS HH MM Constant Alarm Output on FaultTime Control Run ModeCycle Control Lubrication Mode Pump on ControlsPressure Control Rest Mode Pump OFF Controls Backup TimeOFF Time Machine CountAdditional Controls Prelube / Prelube DelayVenting Manual Run Cycle Fault / Warning Scenarios AlarmsCycle Pressure Low Level FaultMachine Count Fault Cycle Pressure FaultMotor Cur SystemRent Warn IngTempera USB ErrorTure Warning Problem Cause Solution TroubleshootingProblem Cause Solution Frequency Component Required Maintenance MaintenanceParts 2 Liter Models Parts 4 Liter and Larger Models Part Description Qty PartsPart Description Qty Part Description Qty 96G124, 96G175, 96G176, 96G186 96G188 Is not intended as a way to Relieve pressure during normal Installation and Repair KitsTechnical Data Model Height Width Depth Inches DimensionsOption Mounting Pattern332305B Graco Information Graco Standard Warranty
Top Page Image Contents