Lincoln Electric IM827-D manual Electric Shock can kill, Location, Mounting

Page 10

A-2	INSTALLATION	A-2

SAFETY PRECAUTION

ELECTRIC SHOCK can kill.

•Only qualified personnel should perform this installation.

•Turn off the input power to the power source at the disconnect switch or fuse box before working on this equipment. Turn off the input power to any other equipment connected to the welding system at the disconnect switch or fuse box before working on this equipment.

•Do not touch electrically hot parts.

----------------------------------------------------------------------------------------

LOCATION

•The Power Feed™ 10M Single Wire Feeder has an IP21 rating, suitable for indoor use.

•The Power Feed™ 10M Single Wire Feeder should be operated in a substantially upright position.

•Do not submerge the Power Feed™ 10M Single Wire Feeder.

•The Power Feed™ 10M Single Wire Feeder is not suitable for stacking.

Locate the Power Feed™ 10M Single Wire Feeder away from radio controlled machinery. The normal operation of the Power Feed™ 10M Single Wire Feeder may adversely affect the operation of RF con- trolled equipment, which may result in bodily injury or damage to the equipment.

FIGURE A.1

MOUNTING

Wire Drive Mounting (See Figure A.1)

The wire drive may be mounted by using the four holes on the bottom. Because the feed plate and gearbox are electrically "hot" when welding, make cer- tain the parts do not contact the any structure or per- son.

Mount the wire drive with the drive rolls in the vertical plane to prevent dirt from collecting in the wire drive. Angle the drive and feed plate to prevent sharp bends in the gun and cable and incoming wire.

Control box Mounting (See Figure A.2)

Boom model Power Feed™ 10M Single Wire Feeder's feature a control box that mounts separately from the wire drive.

The back of the control box has four keyhole slots for mounting. #10 screws are recommended for mount- ing.

FIGURE A.2

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 10

Contents Power Feed 10M Wire Feeder Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Please Examine Carton and Equipment For Damage Immediately On-Line Product Registration TAbLE of Contents TAbLE of Contents Temperature Rating InstallationSPEC.# Type Input Power Power Feed 10M Single Wire FeederLocation Wire Drive Mounting See Figure A.1Electric Shock can kill MountingWeld CAbLE SIzES Weld CAbLE SIzINGWeld CAbLE Connection Electrode LeadCOAxIAL Weld CAbLES Negative Electrode PolarityControl CAbLE Connections Control CAbLE SpecificationsAVAILAbLE Control CAbLE Changing Drive Rolls and Wire Guides DescriptionSet the drive roll pressure by Drive Roll Pressure SettingChanging the GUN Receiver bUSHING To change the gun bushingGUN Receiver bUSHING Welding GUNS, Torches and ACCES- SoriesMagnum GUN and CAbLE ASSEMbLIES Changing the Gear Ratio Wire Feed Shut Down CircuitTo change the gear ratio Spindle Placement Wire Reel LoadingDIP Switch #8 Position Gear Ratio Loading 16 to 44 lb .3 20kg SpoolsUsing K1504-1 Coil Reel Figure A.10Loading 30 lb .6 kg Readi-Reels See Figure A.11 Weld Wire RoutingRemoving a Readi-Reel 13INSTALLATIONA-13 Shielding GAS ConnectionExAMPLES of Connecting AN Arclink Power Wave System Control bOx BOOM ConfigurationWire Drive CV Welding Pulse Welding or STT WeldingWelding Sparks can cause fire or explosion OperationFumes and Gases can be dangerous ARC Rays can burnProduct Description Definitions of Welding ModesCommon Welding AbbREVIATIONS Recommended ProcessesProcess Limitations Required EquipmentAdditional Required Equipment Equipment LimitationsFront Panel Controls and Connections Status LED Prior to Welding Volts / Trim Display and Output KNObSynergic CV Voltage Display LAYOUT-CONTROLS see Figure b.3 Mode Select Panel 4 MSP4Overview LAYOUT-DIGITAL DisplayChanging ARC Wave Control POWER-UP SequenceChanging Weld Modes Infrared IR ControlMachine SETUP/USER Preferences Limit SettingAccessing the Machine Setup Menu SET-UP Features Menu Figure b.3a Setup MenuUser Defined Parameters Parameter Definition Procedure Change Method Stall Factor AdjustmentReset Consumable Weight Parameter Definition Gun Offset AdjustmentCrater Delay TIG Gas ControlDisplay Trim as Volts Option Arc Start/Loss Error TimeDefinition Push-Pull Gun Knob behavior Sense From StudsParameter Definition Show Test Modes 100 View Diagnostics107 View Power Source Protocol 101 View Event LogsStep Trigger Cold Feed / GAS Purge Switch Step / 4-STEP Trigger SwitchStep Trigger Operation Step Trigger Operation Sequence of OperationFigure b.5 Non- Synergic Process Setup and OperationModes Steel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC ControlPulse-on-Pulse Welding Machine Functionality bY Weld Process CC Stick ModesCV GMAW/FCAW NON-SYNERGIC Process Weld ModeOutput Control KNObS, Weld Mode 5 CV NON-SYNERGIC ModesSynergic CV Modes Wire SIzE 030 035 045 052Gmaw Synergic Material Process GASPulse and PULSE-ON-PULSE Synergic Wire SIzEPulse and PULSE-0N-PULSE Modes STT and STT II Modes STT and STT II Synergic035 045 052 Touch Start TIG Gtaw TIG WeldingGtaw Touch Start TIG Welding All Metals Touch Start TIGDIP Switch Settings User MemoriesLow Limit Limit SettingHigh Limit AttributeAccessories OptionalAccessories Lb. coils to 2 spindles Routine Maintenance MaintenanceSafety Precautions CALIbRATION Specification1TROUbLESHOOTINGE-1 Recommended PRObLEMS POSSIbLESymptoms Cause Course of Action ErrNo Heart beat response from See what to Do on Err Error Codes for the Power Wave TROUbLESHOOTING Symptoms OtherCause Recommended Course of Action PRObLEMSThree Dashes LINC-NET System Error Codes Error CodesField Service Facility Arclink System Error CodesYour local Lincoln Authorized PRObLEMS POSSIbLE Output PRObLEMS TROUbLESHOOTING Recommended Power Feed 10M Single Wire DiagramsFeeder Diagrams 14.56 18.48 15.80 Dimension Print30.46 Precaucion Warnung