Lincoln Electric IM827-D manual Process Setup and Operation, Non- Synergic, Modes

Page 42

b-19	OPERATION	b-19

PROCESS SETUP AND OPERATION

The Power Feed™/Power Wave® system delivers world class arc performance for a wide variety of processes. Using the foundation of Waveform Control Technology™, each weld mode is precisely tuned to meet exacting standards for low spatter, weld bead profile and arc shape.

Customized welding software means even the most difficult materials can by welded with the Power Feed™/Power Wave® system. Copper, Nickel, Silicon Bronze are just a few of the unusual alloys the Power Feed™ system welds with ease when special software is loaded.

Figure B.6 below shows a list of weld modes common on many Power Wave power sources. This table is found on the inside front panel door of the Power Feed™ 10M Single Wire Feeder. The specific list of available weld modes depends upon the power source connected to the Power Feed™ 10M Single Wire Feeder wire feeder.

CC- Stick Mode

CC - TIG CC - Gouge

CV - Non Synergic CV - Synergic CV - Pulse

CV - Pulse on Pulse

CV - STT

FIGURE b.6

Non- Synergic	Synergic Modes
Modes

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 42

Contents Power Feed 10M Wire Feeder Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Please Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTAbLE of Contents TAbLE of Contents Temperature Rating InstallationSPEC.# Type Input Power Power Feed 10M Single Wire FeederLocation Wire Drive Mounting See Figure A.1Electric Shock can kill MountingWeld CAbLE SIzES Weld CAbLE SIzINGWeld CAbLE Connection Electrode LeadCOAxIAL Weld CAbLES Negative Electrode PolarityControl CAbLE Specifications Control CAbLE ConnectionsAVAILAbLE Control CAbLE Changing Drive Rolls and Wire Guides DescriptionSet the drive roll pressure by Drive Roll Pressure SettingChanging the GUN Receiver bUSHING To change the gun bushingWelding GUNS, Torches and ACCES- Sories GUN Receiver bUSHINGMagnum GUN and CAbLE ASSEMbLIES Wire Feed Shut Down Circuit Changing the Gear RatioTo change the gear ratio Spindle Placement Wire Reel LoadingDIP Switch #8 Position Gear Ratio Loading 16 to 44 lb .3 20kg SpoolsUsing K1504-1 Coil Reel Figure A.10Weld Wire Routing Loading 30 lb .6 kg Readi-Reels See Figure A.11Removing a Readi-Reel 13INSTALLATIONA-13 Shielding GAS ConnectionExAMPLES of Connecting AN Arclink Power Wave System Control bOx BOOM ConfigurationWire Drive CV Welding Pulse Welding or STT WeldingWelding Sparks can cause fire or explosion OperationFumes and Gases can be dangerous ARC Rays can burnProduct Description Definitions of Welding ModesCommon Welding AbbREVIATIONS Recommended ProcessesProcess Limitations Required EquipmentAdditional Required Equipment Equipment LimitationsFront Panel Controls and Connections Status LED Volts / Trim Display and Output KNOb Prior to WeldingSynergic CV Voltage Display LAYOUT-CONTROLS see Figure b.3 Mode Select Panel 4 MSP4Overview LAYOUT-DIGITAL DisplayChanging ARC Wave Control POWER-UP SequenceChanging Weld Modes Infrared IR ControlLimit Setting Machine SETUP/USER PreferencesAccessing the Machine Setup Menu SET-UP Features Menu Figure b.3a Setup MenuUser Defined Parameters Parameter Definition Procedure Change Method Stall Factor AdjustmentReset Consumable Weight Parameter Definition Gun Offset AdjustmentCrater Delay TIG Gas ControlDisplay Trim as Volts Option Arc Start/Loss Error TimeDefinition Push-Pull Gun Knob behavior Sense From StudsParameter Definition Show Test Modes 100 View Diagnostics107 View Power Source Protocol 101 View Event LogsCold Feed / GAS Purge Switch Step / 4-STEP Trigger Switch Step TriggerStep Trigger Operation Step Trigger Operation Sequence of OperationFigure b.5 Process Setup and Operation Non- SynergicModes Steel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC ControlPulse-on-Pulse Welding Machine Functionality bY Weld Process CC Stick ModesCV GMAW/FCAW NON-SYNERGIC Process Weld ModeOutput Control KNObS, Weld Mode 5 CV NON-SYNERGIC ModesSynergic CV Modes Wire SIzE 030 035 045 052Gmaw Synergic Material Process GASWire SIzE Pulse and PULSE-ON-PULSE SynergicPulse and PULSE-0N-PULSE Modes STT and STT II Synergic STT and STT II Modes035 045 052 Touch Start TIG Gtaw TIG WeldingGtaw Touch Start TIG Welding All Metals Touch Start TIGDIP Switch Settings User MemoriesLow Limit Limit SettingHigh Limit AttributeAccessories OptionalAccessories Lb. coils to 2 spindles Routine Maintenance MaintenanceSafety Precautions CALIbRATION Specification1TROUbLESHOOTINGE-1 Recommended PRObLEMS POSSIbLESymptoms Cause Course of Action ErrNo Heart beat response from See what to Do on Err Error Codes for the Power Wave TROUbLESHOOTING Symptoms OtherPRObLEMS Cause Recommended Course of ActionThree Dashes LINC-NET System Error Codes Error CodesArclink System Error Codes Field Service FacilityYour local Lincoln Authorized PRObLEMS POSSIbLE Output PRObLEMS TROUbLESHOOTING Recommended Diagrams Power Feed 10M Single WireFeeder Diagrams Dimension Print 14.56 18.48 15.8030.46 Precaucion Warnung