Lincoln Electric IM827-D manual Weld Wire Routing, Loading 30 lb .6 kg Readi-Reels See Figure A.11

Page 20

A-12	INSTALLATION	A-12

Loading 30 lb. (13.6 kg) Readi-Reels (See Figure A.11)

A K363-P Readi-Reel adapter is required for loading these spools on 2" (51mm) spindles.

1.Squeeze the release bar on the retaining collar and remove it from the spindle.

Removing a Readi-Reel

1.To remove a Readi-Reel from the an adapter, depress the retaining spring with a thumb while pulling the Readi-Reel cage from the adapter with both hands. Do not remove the adapter from the spindle.

2.Place the Readi-Reel adapter on the spindle, align- ing the spindle brake pin with one of the holes in the adapter.

3.Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle.

4.Rotate the spindle and adapter until the retaining spring is at the 12 o’clock position.

5.Position the Readi-Reel so that electrode de-reels in the proper direction.

6.Set one of the Readi-Reel inside cage wires on the slot in the retaining spring.

7.Lower the Readi-Reel to depress the retaining spring and align the other inside cage wires with the grooves in the adapter.

8.Slide the cage all way onto the adapter until the retaining spring "pops up" fully.

FIGURE A.11

WELD WIRE ROUTING

The electrode supply may be either from reels, Readi- Reels, spools, or bulk packaged drums or reels. Observe the following precautions:

a)The electrode must be routed to the wire drive unit so that the bends in the wire are at a mini- mum, and also that the force required to pull the wire from the reel into the wire drive unit is kept at a minimum.

b)The electrode is “hot” when the gun trigger is pressed and must be insulated from the boom and structure.

c)If more than one wire feed unit shares the same boom and are not sharing the some power source output stud, their wire and reels must be insulated from each other as well as insulated from their mounting structure.

SPINDLE ADAPTER

RETAINING

SPRING

BRAKE

PIN

GROOVES	RETAINING
	COLLAR

READI-

REEL

CAGE

WIRE RELEASE

BAR

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 20

Contents Power Feed 10M Wire Feeder Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Please Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTAbLE of Contents TAbLE of Contents Installation SPEC.# Type Input PowerTemperature Rating Power Feed 10M Single Wire FeederWire Drive Mounting See Figure A.1 Electric Shock can killLocation MountingWeld CAbLE SIzING Weld CAbLE ConnectionWeld CAbLE SIzES Electrode LeadCOAxIAL Weld CAbLES Negative Electrode PolarityAVAILAbLE Control CAbLE Control CAbLE SpecificationsControl CAbLE Connections Changing Drive Rolls and Wire Guides DescriptionDrive Roll Pressure Setting Changing the GUN Receiver bUSHINGSet the drive roll pressure by To change the gun bushingMagnum GUN and CAbLE ASSEMbLIES Welding GUNS, Torches and ACCES- SoriesGUN Receiver bUSHING To change the gear ratio Wire Feed Shut Down CircuitChanging the Gear Ratio Wire Reel Loading DIP Switch #8 Position Gear RatioSpindle Placement Loading 16 to 44 lb .3 20kg SpoolsUsing K1504-1 Coil Reel Figure A.10Removing a Readi-Reel Weld Wire RoutingLoading 30 lb .6 kg Readi-Reels See Figure A.11 13INSTALLATIONA-13 Shielding GAS ConnectionExAMPLES of Connecting AN Arclink Power Wave System BOOM Configuration Wire DriveControl bOx CV Welding Pulse Welding or STT WeldingOperation Fumes and Gases can be dangerousWelding Sparks can cause fire or explosion ARC Rays can burnDefinitions of Welding Modes Common Welding AbbREVIATIONSProduct Description Recommended ProcessesRequired Equipment Additional Required EquipmentProcess Limitations Equipment LimitationsFront Panel Controls and Connections Status LED Synergic CV Voltage Display Volts / Trim Display and Output KNObPrior to Welding Mode Select Panel 4 MSP4 OverviewLAYOUT-CONTROLS see Figure b.3 LAYOUT-DIGITAL DisplayPOWER-UP Sequence Changing Weld ModesChanging ARC Wave Control Infrared IR ControlAccessing the Machine Setup Menu Limit SettingMachine SETUP/USER Preferences SET-UP Features Menu Figure b.3a Setup MenuUser Defined Parameters Parameter Definition Procedure Change Method Stall Factor AdjustmentParameter Definition Gun Offset Adjustment Crater DelayReset Consumable Weight TIG Gas ControlArc Start/Loss Error Time Definition Push-Pull Gun Knob behaviorDisplay Trim as Volts Option Sense From Studs100 View Diagnostics 107 View Power Source ProtocolParameter Definition Show Test Modes 101 View Event LogsStep Trigger Operation Cold Feed / GAS Purge Switch Step / 4-STEP Trigger SwitchStep Trigger Step Trigger Operation Sequence of OperationFigure b.5 Modes Process Setup and OperationNon- Synergic Steel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC ControlPulse-on-Pulse Welding Machine Functionality bY Weld Process CC Stick ModesProcess Weld Mode Output Control KNObS, Weld Mode 5CV GMAW/FCAW NON-SYNERGIC CV NON-SYNERGIC ModesWire SIzE 030 035 045 052 Gmaw SynergicSynergic CV Modes Material Process GASPulse and PULSE-0N-PULSE Modes Wire SIzEPulse and PULSE-ON-PULSE Synergic 035 045 052 STT and STT II SynergicSTT and STT II Modes Gtaw TIG Welding Gtaw Touch Start TIG WeldingTouch Start TIG All Metals Touch Start TIGDIP Switch Settings User MemoriesLimit Setting High LimitLow Limit AttributeAccessories OptionalAccessories Lb. coils to 2 spindles Maintenance Safety PrecautionsRoutine Maintenance CALIbRATION Specification1TROUbLESHOOTINGE-1 PRObLEMS POSSIbLE Symptoms Cause Course of ActionRecommended ErrNo Heart beat response from See what to Do on Err Error Codes for the Power Wave TROUbLESHOOTING Symptoms OtherThree Dashes PRObLEMSCause Recommended Course of Action LINC-NET System Error Codes Error CodesYour local Lincoln Authorized Arclink System Error CodesField Service Facility PRObLEMS POSSIbLE Output PRObLEMS TROUbLESHOOTING Recommended Feeder DiagramsPower Feed 10M Single Wire Diagrams 30.46 Dimension Print14.56 18.48 15.80 Precaucion Warnung