Wagner SprayTech Model 9140 owner manual Cleanup, Purging the Paint Hose, Cleaning the Suction SET

Page 10

IMPORTANT CLEANING

NOTES!

READ THESE NOTES AND

WARNINGS BEFORE YOU

START TO CLEAN YOUR

SPRAYER!

•When using latex paints, clean your sprayer and components using warm, soapy water.

When using oil-based paints, use mineral spirits.

•Do not use mineral spirits on latex paint, or the mixture will turn into a jelly-like substance which is difficult to remove.

•No matter which cleaning solution you use, make sure to dispose of it properly when finished cleaning your sprayer.

•Thorough cleaning and lubrication of the sprayer is the most important step you can take to ensure proper operation after storage.

CALL 1-800-880-0993

IF YOU HAVE ANY QUESTIONS REGARDING THE CLEANUP OF YOUR SPRAYER

WARNING

Special cleanup instructions for use with flammable solvents:

•ALWAYS FLUSH SPRAY GUN AT LEAST ONE HOSE LENGTH AWAY FROM SPRAY PUMP.

•If collecting flushed solvents in one gallon metal container, place it into an empty five gallon container, then flush.

•Area must be free from vapors.

•Follow all cleanup instructions.

CLEANUP

PURGING THE PAINT HOSE

These steps will allow you to recover excess paint left over in the paint hose.

1.Lock the gun and remove spray tip assembly.

2.Submerge suction set into a bucket with appropriate cleaning solution.

3.Hold the spray gun against the side of the paint can and hold the trigger.

4.While holding the trigger, turn the pump ON (l), and turn the PRIME/SPRAY knob to SPRAY.

PRIME

l

SPRAY

Let the pump run until all paint is purged from the hose and cleaning solution is coming out of the gun.

5.Release the trigger.

6.Hold the spray gun against the side of a separate container and hold the trigger.

7.Trigger the gun until the fluid coming out of the gun is clear.

8.Turn the PRIME/SPRAY knob to PRIME and trigger gun once more to relieve pressure.

9.Move on to Cleaning the Suction

Set.

CLEANING THE SUCTION SET

1.

Lock the gun and turn

 

 

the pump OFF (O).

o

2.

Remove the suction

 

hose and return tube and clean it using the appropriate cleaning solution.

You should also wipe the threads of the inlet valve, and remove and clean the suction set screen.

3.When suction set is clean, thread the suction tube back onto the inlet valve, and replace the return tube onto the return tube fitting. Replace clip.

Return tube

fitting

Inlet valve

Clip

Return tube Suction set

4.Submerge the suction set into a bucket of NEW cleaning solution.

5.Turn the PRIME/SPRAY knob to PRIME, turn the pump to ON (l), and trigger the gun into a waste container to relieve the pressure.

PRIME

SPRAY

l

6.Let the pump circulate the cleaning solution through the suction set for 2- 3 minutes.

7.Turn the pump OFF (O).

8.Move on to Cleaning the Spray Gun, next page.

English

Customer Service: 800-880-0993 10

© 2003 Wagner Spray Tech - All rights reserved.

 

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Specifications Table of ContentsHigh Performance Airless Sprayer Safety Information Read ALL Safety Important Electrical Information Grounding InstructionsComponents Components and DescriptionControls and Functions SETUP--ASSEMBLING the Sprayer Plugging in the Sprayer Pressure Relief ProcedureBefore YOU Begin Before YOU Prime the SprayerPurging & Priming Your hose is now purged and primed. You are ready to paintPractice SprayingSpraying Technique Cleaning the Suction SET Screen Spraying TroubleshootingCleaning the Spray GUN Filter Unclogging the Spray TIPMove on to Cleaning the Suction Set CleanupCleaning the Suction SET Move on to Cleaning the Spray Gun, nextCleaning the Spray GUN Filter and TIP Assembly Shutdown StoragePreparing the Sprayer for LONG- Term Storage StartupDaily Maintenance MaintenanceAccessories Extended MaintenanceDisassembly of the Fluid Section Fluid Section Seal Replacement InstructionsAssembly of the Fluid Section Solution TroubleshootingProblem CausePage Characté Ristiques Techniques Pulvérisateur Sans AIR PerformantTable DES Matières Le modè le sur support est illustré dans leConsignes DE SÉ Curite Lire Toutes CES Renseignements Importants SUR L’É Lectricité Directives DE Mise À LA TerreComposants Commandes ET FonctionsDescription ET Composants Bouton de ré gulation de la pressionPRÉ PARATION--ASSEMBLAGE DU Pulvé Risateur DÉ Compression Avant DE CommencerBranchement DU Pulvé Risateur Filtrage DU ProduitTube de Purge ET Amorç AGEDaspiration RetourEssais Pulvé RisationTechniques DE Pulvé Risation Nettoyage DE L’EMBOUT DE Pulvé Risation Problè MES PotentielsNettoyage DU Filtre DE Pistolet Nettoyage DE LA CRÉ PinePurge DU Flexible NettoyageRemarques Importantes AU Sujet DU Nettoyage Nettoyage DU Dispositif D’ASPIRATIONNETTOYAGE--SUITE GX-08/10PRÉ Paration Pour LE Rangement RangementRangement À Court Terme JUSQU’À 16 Heures PRÉ Paration EN VUE DE LA RÉ -UTILISATIONMaintenance À Long Terme AccessoiresEntretien Quotidien Vis DÉ Sassemblage DU Tronç onAssemblage DU Tronç on 5a. En pré sence du modè lesDÉ Pannage PrimePage Contenido Rociador SIN Aire DE Alto RendimientoEspecificaciones Informació N DE Seguridad LEA Toda LA Informació N ELÉ Ctrica Importante Instrucciones Para LA Conexió N a TierraPistola/Boquilla ComponentesControles Y Funciones Rociadora Procedimiento para aliviar laPreparació N--ENSAMBLADO DEL Rociador Procedimiento Para Aliviar LA Presió N Antes DE ComenzarCÓ MO Enchufar EL Rociador Antes DE Cebar EL RociadorPurga Y Cebado DE LA Bomba Purga Y CebadoPurga Y Cebado DE LA Manguera PRÁ Ctica RociadoTÉ Cnica DE Aplicació N Limpieza DEL Filtro DE LA Pistola Rociadora Solució N DE Problemas DE Aplicació NDesbloqueo DE LA Boquilla Rociadora Limpieza DE LA Malla DEL Juego DE Succió NLimpieza DEL Juego DE Succió N LimpiezaPurga DE LA Manguera DE Pintura Avance a la Limpieza del juego de succió nProtector LIMPIEZA--CONTINUACIÓ NFiltro Sello deParo AlmacenamientoAlmacenamiento DE Corto Plazo Hasta 16 Horas ArranqueReemplazo DE LA VÁ Lvula DE Entrada AccessoriosMantenimiento Mantenimiento DiarioEnsamblado DE LA Secció N DE Líquidos Desmontaje DE LA Secció N DE FluidosSolució N DE Problemas Parts List Liste DE PIÈ CES Lista DE Piezas Suction SET Dispositif ’ASPIRATION Juego DE Succió NArticle N de piè ce Description Quantity Articulo0347706 02962910296343 0296262Articulo Pieza# Descripció n Cantidad Article N de piè ce Description QuantitéMinneapolis, Minnesota Wagner Spray Tech CorporationFernbrook Lane Telephone
Top Page Image Contents