Wagner SprayTech Model 9140 owner manual Practice, Spraying Technique

Page 8

SPRAYING

PRACTICE

CAUTION

Be sure that the paint hose is free of kinks and clear of objects with sharp cutting edges.

	1. Switch the pump ON (l)	PRIME
	and turn the	PRIME
	and turn the
	PRIME/SPRAY knob to
	SPRAY.
		SPRAY

2.Turn the pressure contol

dial to its highest setting

(+). The spray hose should stiffen as paint

begins to flow through it.

3.When the motor shuts off, unlock the spray gun and spray a test area to check the spray pattern.

When enough pressure has built up in the hose, the motor will shut off automatically. The motor will cycle on and off automatically as it needs pressure.

The pressure control	Good spray pattern
dial can be adjusted up
or down to achieve the
desired spray pattern.
	Paint tailing pattern
	Paint tailing pattern

SPRAYING TECHNIQUE

The key to a good paint job is an even coating over the entire surface. This is done by using even strokes. Follow the TIPS, below.

TIP:	Keep your arm moving at a constant speed and
	keep the spray gun at a constant distance from
	the surface. The best spraying distance is 10 to
	12 inches between the spray tip and the surface.

Even coat throughout

Approximately 10 to 12 inches

Keep stroke smooth and at an even speed.

TIP: Keep the spray gun perpendicular to the surface, otherwise one end of the pattern will be thicker than the other.

Approximately 10 to 12 inches

Right way

Wrong way

TIP: Keep the spray gun at right angles to the surface. This means moving your entire arm back and forth rather than just flexing your wrist.

Light Coat

Heavy Coat

Light Coat

Do not flex wrist while spraying.

TIP: The spray gun should be triggered by turning it on and off with each stroke. Do not trigger the gun during the middle of a stroke. This will result in an uneven spray and splotchy coverage.

Proper way to trigger the spray gun

Keep stroke

Approximately

even

10 to 12 inches

Start stroke

Pull trigger

Keep steady

Release trigger End stroke

ADDITIONAL TIPS

Overlap each stroke by about 30%. This will ensure an even coating.

When you stop painting, follow PRESSURE RELIEF PROCEDURE.

IF YOU EXPECT TO BE AWAY FROM YOUR SPRAYER FOR MORE THAN ONE HOUR, FOLLOW THE SHORT- TERM CLEANUP PROCEDURE DESCRIBED IN THE STORAGE SECTION OF THIS MANUAL (page 12).

English	Customer Service: 800-880-0993 8	© 2003 Wagner Spray Tech - All rights reserved.

Image 8

Contents High Performance Airless Sprayer Table of ContentsSpecifications Safety Information Read ALL Safety Important Electrical Information Grounding InstructionsControls and Functions Components and DescriptionComponents SETUP--ASSEMBLING the Sprayer Pressure Relief Procedure Before YOU BeginPlugging in the Sprayer Before YOU Prime the SprayerPurging & Priming Your hose is now purged and primed. You are ready to paintSpraying Technique SprayingPractice Spraying Troubleshooting Cleaning the Spray GUN FilterCleaning the Suction SET Screen Unclogging the Spray TIPCleanup Cleaning the Suction SETMove on to Cleaning the Suction Set Move on to Cleaning the Spray Gun, nextCleaning the Spray GUN Filter and TIP Assembly Storage Preparing the Sprayer for LONG- Term StorageShutdown StartupMaintenance AccessoriesDaily Maintenance Extended MaintenanceAssembly of the Fluid Section Fluid Section Seal Replacement InstructionsDisassembly of the Fluid Section Troubleshooting ProblemSolution CausePage Pulvérisateur Sans AIR Performant Table DES MatièresCharacté Ristiques Techniques Le modè le sur support est illustré dans leConsignes DE SÉ Curite Lire Toutes CES Renseignements Importants SUR L’É Lectricité Directives DE Mise À LA TerreCommandes ET Fonctions Description ET ComposantsComposants Bouton de ré gulation de la pressionPRÉ PARATION--ASSEMBLAGE DU Pulvé Risateur Avant DE Commencer Branchement DU Pulvé RisateurDÉ Compression Filtrage DU ProduitPurge ET Amorç AGE DaspirationTube de RetourTechniques DE Pulvé Risation Pulvé RisationEssais Problè MES Potentiels Nettoyage DU Filtre DE PistoletNettoyage DE L’EMBOUT DE Pulvé Risation Nettoyage DE LA CRÉ PineNettoyage Remarques Importantes AU Sujet DU NettoyagePurge DU Flexible Nettoyage DU Dispositif D’ASPIRATIONNETTOYAGE--SUITE GX-08/10Rangement Rangement À Court Terme JUSQU’À 16 HeuresPRÉ Paration Pour LE Rangement PRÉ Paration EN VUE DE LA RÉ -UTILISATIONEntretien Quotidien AccessoiresMaintenance À Long Terme DÉ Sassemblage DU Tronç on Assemblage DU Tronç onVis 5a. En pré sence du modè lesDÉ Pannage PrimePage Especificaciones Rociador SIN Aire DE Alto RendimientoContenido Informació N DE Seguridad LEA Toda LA Informació N ELÉ Ctrica Importante Instrucciones Para LA Conexió N a TierraComponentes Controles Y FuncionesPistola/Boquilla Rociadora Procedimiento para aliviar laPreparació N--ENSAMBLADO DEL Rociador Antes DE Comenzar CÓ MO Enchufar EL RociadorProcedimiento Para Aliviar LA Presió N Antes DE Cebar EL RociadorPurga Y Cebado DE LA Manguera Purga Y CebadoPurga Y Cebado DE LA Bomba TÉ Cnica DE Aplicació N RociadoPRÁ Ctica Solució N DE Problemas DE Aplicació N Desbloqueo DE LA Boquilla RociadoraLimpieza DEL Filtro DE LA Pistola Rociadora Limpieza DE LA Malla DEL Juego DE Succió NLimpieza Purga DE LA Manguera DE PinturaLimpieza DEL Juego DE Succió N Avance a la Limpieza del juego de succió nLIMPIEZA--CONTINUACIÓ N FiltroProtector Sello deAlmacenamiento Almacenamiento DE Corto Plazo Hasta 16 HorasParo ArranqueAccessorios MantenimientoReemplazo DE LA VÁ Lvula DE Entrada Mantenimiento DiarioEnsamblado DE LA Secció N DE Líquidos Desmontaje DE LA Secció N DE FluidosSolució N DE Problemas Parts List Liste DE PIÈ CES Lista DE Piezas Suction SET Dispositif ’ASPIRATION Juego DE Succió NArticle N de piè ce Description Quantity Articulo0296291 02963430347706 0296262Articulo Pieza# Descripció n Cantidad Article N de piè ce Description QuantitéWagner Spray Tech Corporation Fernbrook LaneMinneapolis, Minnesota Telephone