Wagner SprayTech Model 9140 owner manual Purging & Priming

Page 7

PURGING & PRIMING

PURGING AND PRIMING THE PUMP

PURGING AND PRIMING THE SPRAY HOSE

1.	Place a full container of
	paint underneath the	Suction
	suction tube.	tube
2.	Secure the return tube	Return
	into a waste container.	Return
	into a waste container.	tube

3. Turn the pressure control dial to maximum pressure

(+).

1.Unlock the spray gun and turn PRIME/SPRAY knob to PRIME.

Your spray tip SHOULD NOT be attached to your spray gun when purging your spray hose.

2.Trigger and HOLD the spray gun into a waste container.

3.While holding the trigger, switch the pump ON (l).

PRIME

SPRAY

4. Turn the PRIME/SPRAY	PRIME	SPRAY
4. Turn the PRIME/SPRAY
knob to PRIME.

5.Plug in the sprayer, and move the ON/OFF switch to the ON position.

l

The unit will begin to draw paint up the suction tube, into the pump, and out the return tube. Let the unit cycle long enough to remove test fluid from the pump, or until paint is coming from the return tube.

6.Switch the pump to OFF (O).

7.Remove the return tube from the waste container and place it in its operating position above the container of paint. Use the metal clip to bind the two hoses together.

Your sprayer is now purged. Move to Purging and Priming the Spray Hose.

	4. While holding the trigger,	PRIME
	turn the PRIME/SPRAY	PRIME
	turn the PRIME/SPRAY
	knob to SPRAY. Hold the
	trigger until all air, water, or
	solvent is purged from the
	spray hose and paint is	SPRAY
	flowing freely (read
	warnings below).

WARNING

Keep hands clear from fluid stream.

WARNING

Using a metal container, ground

the gun by holding it against the edge of the container while

flushing. Failure to do so may lead to a static electric discharge which may cause a fire.

If the PRIME/SPRAY knob is still

on SPRAY, there will be high pressure in the hose and spray gun until the PRIME/SPRAY knob is turned to PRIME.

5.Release trigger, turn the

PRIME/SPRAY knob to

PRIME and turn pump PRIME SPRAYo OFF (O).

6.Trigger the gun into the waste container once more to be sure that no pressure is left in the hose.

7.Lock the spray gun off.

8.Thread the spray tip guard assembly onto the gun. Tighten by hand.

Begin		to achieve
Begin		to achieve
tightening		the desired
the tip at		spray angle
this angle		when tight.

Your hose is now purged and primed. You are ready to paint.

© 2003 Wagner Spray Tech - All rights reserved.	7	Customer Service: 800-880-0993	English

Image 7

Contents Specifications Table of ContentsHigh Performance Airless Sprayer Safety Information Read ALL Safety Grounding Instructions Important Electrical InformationComponents Components and DescriptionControls and Functions SETUP--ASSEMBLING the Sprayer Before YOU Prime the Sprayer Pressure Relief ProcedureBefore YOU Begin Plugging in the SprayerYour hose is now purged and primed. You are ready to paint Purging & PrimingPractice SprayingSpraying Technique Unclogging the Spray TIP Spraying TroubleshootingCleaning the Spray GUN Filter Cleaning the Suction SET ScreenMove on to Cleaning the Spray Gun, next CleanupCleaning the Suction SET Move on to Cleaning the Suction SetCleaning the Spray GUN Filter and TIP Assembly Startup StoragePreparing the Sprayer for LONG- Term Storage ShutdownExtended Maintenance MaintenanceAccessories Daily MaintenanceDisassembly of the Fluid Section Fluid Section Seal Replacement InstructionsAssembly of the Fluid Section Cause TroubleshootingProblem SolutionPage Le modè le sur support est illustré dans le Pulvérisateur Sans AIR PerformantTable DES Matières Characté Ristiques TechniquesConsignes DE SÉ Curite Lire Toutes CES Directives DE Mise À LA Terre Renseignements Importants SUR L’É LectricitéBouton de ré gulation de la pression Commandes ET FonctionsDescription ET Composants ComposantsPRÉ PARATION--ASSEMBLAGE DU Pulvé Risateur Filtrage DU Produit Avant DE CommencerBranchement DU Pulvé Risateur DÉ CompressionRetour Purge ET Amorç AGEDaspiration Tube deEssais Pulvé RisationTechniques DE Pulvé Risation Nettoyage DE LA CRÉ Pine Problè MES PotentielsNettoyage DU Filtre DE Pistolet Nettoyage DE L’EMBOUT DE Pulvé RisationNettoyage DU Dispositif D’ASPIRATION NettoyageRemarques Importantes AU Sujet DU Nettoyage Purge DU FlexibleGX-08/10 NETTOYAGE--SUITEPRÉ Paration EN VUE DE LA RÉ -UTILISATION RangementRangement À Court Terme JUSQU’À 16 Heures PRÉ Paration Pour LE RangementMaintenance À Long Terme AccessoiresEntretien Quotidien 5a. En pré sence du modè les DÉ Sassemblage DU Tronç onAssemblage DU Tronç on VisPrime DÉ PannagePage Contenido Rociador SIN Aire DE Alto RendimientoEspecificaciones Informació N DE Seguridad LEA Toda LA Instrucciones Para LA Conexió N a Tierra Informació N ELÉ Ctrica ImportanteRociadora Procedimiento para aliviar la ComponentesControles Y Funciones Pistola/BoquillaPreparació N--ENSAMBLADO DEL Rociador Antes DE Cebar EL Rociador Antes DE ComenzarCÓ MO Enchufar EL Rociador Procedimiento Para Aliviar LA Presió NPurga Y Cebado DE LA Bomba Purga Y CebadoPurga Y Cebado DE LA Manguera PRÁ Ctica RociadoTÉ Cnica DE Aplicació N Limpieza DE LA Malla DEL Juego DE Succió N Solució N DE Problemas DE Aplicació NDesbloqueo DE LA Boquilla Rociadora Limpieza DEL Filtro DE LA Pistola RociadoraAvance a la Limpieza del juego de succió n LimpiezaPurga DE LA Manguera DE Pintura Limpieza DEL Juego DE Succió NSello de LIMPIEZA--CONTINUACIÓ NFiltro ProtectorArranque AlmacenamientoAlmacenamiento DE Corto Plazo Hasta 16 Horas ParoMantenimiento Diario AccessoriosMantenimiento Reemplazo DE LA VÁ Lvula DE EntradaDesmontaje DE LA Secció N DE Fluidos Ensamblado DE LA Secció N DE LíquidosSolució N DE Problemas Suction SET Dispositif ’ASPIRATION Juego DE Succió N Parts List Liste DE PIÈ CES Lista DE PiezasArticulo Article N de piè ce Description Quantity0296262 02962910296343 0347706Article N de piè ce Description Quantité Articulo Pieza# Descripció n CantidadTelephone Wagner Spray Tech CorporationFernbrook Lane Minneapolis, Minnesota