Wagner SprayTech Model 9140 owner manual SETUP--ASSEMBLING the Sprayer

Page 5

SETUP--ASSEMBLING THE SPRAYER

TOOLS NEEDED FOR SETUP

•Two adjustable wrenches

•3/16” allen wrench

•Extension cord (refer to Important Electrical Information (page 3).

WARNING

Do not plug in the unit until setup is complete.

ATTACHING THE HANDLE (CART MODELS)

1.Position the handle against the cart so that the holes in the handle

line up with the holes in the cart.

2. Insert the bolts through the holes in the handle and cart and locking washers.

3. Tighten the wing nuts onto the bolts by hand.

ATTACHING THE PAIL BRACKET (CART MODELS)

1. Position the pail bracket against the unit so that the holes in the unit line up with the holes in the

ATTACHING THE SPRAY GUN

1. Thread spray gun onto the other end of the hose.

Hold the gun with one adjustable wrench, and tighten with the other.

ATTACHING THE SUCTION SET & RETURN TUBE

1.Attach the suction tube to the inlet valve and tighten firmly by hand. Be sure that the threads are straight so that the fitting turns freely.

2.Press the return tube onto the return tube fitting.

3.Squeeze clip over the return tube fitting to secure return tube.

Return tube

fitting

Inlet valve

Clip

Return tube

Suction set

LOCKING AND UNLOCKING THE SPRAY GUN

WARNING

Always lock the trigger off when attaching the spray tip or when the spray gun is not in use. Refer to Spray Gun/Tip Chart on page 4 to determine the gun model you have.

bracket.

2. Insert the bolts through the holes in the bracket and the unit.

3. Tighten the bolts with a 3/16” allen wrench.

ATTACHING THE PAINT HOSE

GUN MODELS GX-06AND

GX-07

The gun is secured when the trigger lock is at a 90° angle (perpendicular) to the trigger in either direction.

GX-06/07

Gun locked (gun will not spray)

1.Thread the high pressure hose to the paint hose port.

2.Tighten with an adjustable

wrench.

3. Remove pusher stem from inlet valve.

GX-08/10

Gun locked

(gun will not spray)

GUN MODELS GX-08AND

GX-10

To lock the gun, turn the trigger lock forward and slightly down until it stops.

The spray tip SHOULD NOT be attached until after the sprayer and paint hose have been purged and primed.

© 2003 Wagner Spray Tech - All rights reserved.

5

Customer Service: 800-880-0993

English

Image 5

Contents High Performance Airless Sprayer Table of ContentsSpecifications Safety Information Read ALL Safety Grounding Instructions Important Electrical InformationControls and Functions Components and DescriptionComponents SETUP--ASSEMBLING the Sprayer Before YOU Begin Pressure Relief ProcedurePlugging in the Sprayer Before YOU Prime the SprayerYour hose is now purged and primed. You are ready to paint Purging & PrimingSpraying Technique SprayingPractice Cleaning the Spray GUN Filter Spraying TroubleshootingCleaning the Suction SET Screen Unclogging the Spray TIPCleaning the Suction SET CleanupMove on to Cleaning the Suction Set Move on to Cleaning the Spray Gun, nextCleaning the Spray GUN Filter and TIP Assembly Preparing the Sprayer for LONG- Term Storage StorageShutdown StartupAccessories MaintenanceDaily Maintenance Extended MaintenanceAssembly of the Fluid Section Fluid Section Seal Replacement InstructionsDisassembly of the Fluid Section Problem TroubleshootingSolution CausePage Table DES Matières Pulvérisateur Sans AIR PerformantCharacté Ristiques Techniques Le modè le sur support est illustré dans leConsignes DE SÉ Curite Lire Toutes CES Directives DE Mise À LA Terre Renseignements Importants SUR L’É LectricitéDescription ET Composants Commandes ET FonctionsComposants Bouton de ré gulation de la pressionPRÉ PARATION--ASSEMBLAGE DU Pulvé Risateur Branchement DU Pulvé Risateur Avant DE CommencerDÉ Compression Filtrage DU ProduitDaspiration Purge ET Amorç AGETube de RetourTechniques DE Pulvé Risation Pulvé RisationEssais Nettoyage DU Filtre DE Pistolet Problè MES PotentielsNettoyage DE L’EMBOUT DE Pulvé Risation Nettoyage DE LA CRÉ PineRemarques Importantes AU Sujet DU Nettoyage NettoyagePurge DU Flexible Nettoyage DU Dispositif D’ASPIRATIONGX-08/10 NETTOYAGE--SUITERangement À Court Terme JUSQU’À 16 Heures RangementPRÉ Paration Pour LE Rangement PRÉ Paration EN VUE DE LA RÉ -UTILISATIONEntretien Quotidien AccessoiresMaintenance À Long Terme Assemblage DU Tronç on DÉ Sassemblage DU Tronç onVis 5a. En pré sence du modè lesPrime DÉ PannagePage Especificaciones Rociador SIN Aire DE Alto RendimientoContenido Informació N DE Seguridad LEA Toda LA Instrucciones Para LA Conexió N a Tierra Informació N ELÉ Ctrica ImportanteControles Y Funciones ComponentesPistola/Boquilla Rociadora Procedimiento para aliviar laPreparació N--ENSAMBLADO DEL Rociador CÓ MO Enchufar EL Rociador Antes DE ComenzarProcedimiento Para Aliviar LA Presió N Antes DE Cebar EL RociadorPurga Y Cebado DE LA Manguera Purga Y CebadoPurga Y Cebado DE LA Bomba TÉ Cnica DE Aplicació N RociadoPRÁ Ctica Desbloqueo DE LA Boquilla Rociadora Solució N DE Problemas DE Aplicació NLimpieza DEL Filtro DE LA Pistola Rociadora Limpieza DE LA Malla DEL Juego DE Succió NPurga DE LA Manguera DE Pintura LimpiezaLimpieza DEL Juego DE Succió N Avance a la Limpieza del juego de succió nFiltro LIMPIEZA--CONTINUACIÓ NProtector Sello deAlmacenamiento DE Corto Plazo Hasta 16 Horas AlmacenamientoParo ArranqueMantenimiento AccessoriosReemplazo DE LA VÁ Lvula DE Entrada Mantenimiento DiarioDesmontaje DE LA Secció N DE Fluidos Ensamblado DE LA Secció N DE LíquidosSolució N DE Problemas Suction SET Dispositif ’ASPIRATION Juego DE Succió N Parts List Liste DE PIÈ CES Lista DE PiezasArticulo Article N de piè ce Description Quantity0296343 02962910347706 0296262Article N de piè ce Description Quantité Articulo Pieza# Descripció n CantidadFernbrook Lane Wagner Spray Tech CorporationMinneapolis, Minnesota Telephone