Wagner SprayTech Model 9140 Before YOU Begin, Plugging in the Sprayer, Pressure Relief Procedure

Page 6

BEFORE YOU BEGIN

This column contains instructions that will be repeated throughout this manual.

PLUGGING IN THE SPRAYER

1.	Check that the ON/OFF	o
	switch is in the OFF	o
	switch is in the OFF
	position.
2.	Plug the sprayer into a
	heavy duty grounded
	extension cord. Refer to
	Important Electrical
	Information, page 3).

PRESSURE RELIEF PROCEDURE

WARNING

Be sure to follow the pressure relief procedure (page 6) when shutting the unit off FOR ANY PURPOSE. This procedure is used to relieve pressure from the spray hose.

1. Lock the spray gun off.

GX-06/07

GX-08/10

CHOOSING THE CORRECT SPRAY GUN FILTER

Use the proper gun filter based on the tip size being used.

Part No.	Tip Size	Filter	Mesh	Color of	Qty.
		Type	Number	Filter
				Body
0154918	.011	Extrafine	180 mesh	red	2 pack
			0.084 mm

0154675	.013 - .015	Fine	100 mesh	yellow	2 pack
			0.140 mm

0154842	.017 - .023	Medium	50 mesh	white	2 pack
			0.315 mm

BEFORE YOU PRIME THE SPRAYER

Before priming, squirt a teaspoon of separating oil (P/N 0154908 included with unit) into the indicated area. Light household oil can be substituted if necessary. Do not put more than a teaspoon into the lubricating area. Too much oil will leak down into your paint.

IF YOUR UNIT IS NEW. . .

2.Flip the ON/OFF switch to the OFF (O) position.

3.Unlock the spray gun, turn the PRIME/SPRAY knob to PRIME, and trigger spray gun into paint bucket.

4.Lock the spray gun.

o

PRIME

SPRAY

All units are performance-tested at the factory and are shipped with test fluid in the fluid section to prevent corrosion during shipment and storage.

•Whether you are going to spray latex or oil-based paints, this fluid must be purged and thoroughly cleaned out of the system (follow Purging and Priming the Pump steps, page 7).

IF YOUR UNIT HAS ALREADY BEEN USED. . .

If the pump has already been used you will need to purge the water or solvent used in cleanup and storage.

PAINT STRAINING

It is recommended that in order to avoid premature tip and gun clogging you should strain your paint before spraying. Follow manufacturer’s recommendations.

English	Customer Service: 800-880-0993 6	© 2003 Wagner Spray Tech - All rights reserved.

Image 6

Contents Table of Contents SpecificationsHigh Performance Airless Sprayer Safety Information Read ALL Safety Important Electrical Information Grounding InstructionsComponents and Description ComponentsControls and Functions SETUP--ASSEMBLING the Sprayer Plugging in the Sprayer Pressure Relief ProcedureBefore YOU Begin Before YOU Prime the SprayerPurging & Priming Your hose is now purged and primed. You are ready to paintSpraying PracticeSpraying Technique Cleaning the Suction SET Screen Spraying TroubleshootingCleaning the Spray GUN Filter Unclogging the Spray TIPMove on to Cleaning the Suction Set CleanupCleaning the Suction SET Move on to Cleaning the Spray Gun, nextCleaning the Spray GUN Filter and TIP Assembly Shutdown StoragePreparing the Sprayer for LONG- Term Storage StartupDaily Maintenance MaintenanceAccessories Extended MaintenanceFluid Section Seal Replacement Instructions Disassembly of the Fluid SectionAssembly of the Fluid Section Solution TroubleshootingProblem CausePage Characté Ristiques Techniques Pulvérisateur Sans AIR PerformantTable DES Matières Le modè le sur support est illustré dans leConsignes DE SÉ Curite Lire Toutes CES Renseignements Importants SUR L’É Lectricité Directives DE Mise À LA TerreComposants Commandes ET FonctionsDescription ET Composants Bouton de ré gulation de la pressionPRÉ PARATION--ASSEMBLAGE DU Pulvé Risateur DÉ Compression Avant DE CommencerBranchement DU Pulvé Risateur Filtrage DU ProduitTube de Purge ET Amorç AGEDaspiration RetourPulvé Risation EssaisTechniques DE Pulvé Risation Nettoyage DE L’EMBOUT DE Pulvé Risation Problè MES PotentielsNettoyage DU Filtre DE Pistolet Nettoyage DE LA CRÉ PinePurge DU Flexible NettoyageRemarques Importantes AU Sujet DU Nettoyage Nettoyage DU Dispositif D’ASPIRATIONNETTOYAGE--SUITE GX-08/10PRÉ Paration Pour LE Rangement RangementRangement À Court Terme JUSQU’À 16 Heures PRÉ Paration EN VUE DE LA RÉ -UTILISATIONAccessoires Maintenance À Long TermeEntretien Quotidien Vis DÉ Sassemblage DU Tronç onAssemblage DU Tronç on 5a. En pré sence du modè lesDÉ Pannage PrimePage Rociador SIN Aire DE Alto Rendimiento ContenidoEspecificaciones Informació N DE Seguridad LEA Toda LA Informació N ELÉ Ctrica Importante Instrucciones Para LA Conexió N a TierraPistola/Boquilla ComponentesControles Y Funciones Rociadora Procedimiento para aliviar laPreparació N--ENSAMBLADO DEL Rociador Procedimiento Para Aliviar LA Presió N Antes DE ComenzarCÓ MO Enchufar EL Rociador Antes DE Cebar EL RociadorPurga Y Cebado Purga Y Cebado DE LA BombaPurga Y Cebado DE LA Manguera Rociado PRÁ CticaTÉ Cnica DE Aplicació N Limpieza DEL Filtro DE LA Pistola Rociadora Solució N DE Problemas DE Aplicació NDesbloqueo DE LA Boquilla Rociadora Limpieza DE LA Malla DEL Juego DE Succió NLimpieza DEL Juego DE Succió N LimpiezaPurga DE LA Manguera DE Pintura Avance a la Limpieza del juego de succió nProtector LIMPIEZA--CONTINUACIÓ NFiltro Sello deParo AlmacenamientoAlmacenamiento DE Corto Plazo Hasta 16 Horas ArranqueReemplazo DE LA VÁ Lvula DE Entrada AccessoriosMantenimiento Mantenimiento DiarioEnsamblado DE LA Secció N DE Líquidos Desmontaje DE LA Secció N DE FluidosSolució N DE Problemas Parts List Liste DE PIÈ CES Lista DE Piezas Suction SET Dispositif ’ASPIRATION Juego DE Succió NArticle N de piè ce Description Quantity Articulo0347706 02962910296343 0296262Articulo Pieza# Descripció n Cantidad Article N de piè ce Description QuantitéMinneapolis, Minnesota Wagner Spray Tech CorporationFernbrook Lane Telephone