Hitachi NR90AA instruction manual Nailer Operation

Page 12

English

(2)Insert nail strips one by one from above the magazine. Two strips can be loaded at one time.

Nail Strip

Magazine

(3)Press the stop lever and slide the nail feeder forward until it contacts the nail strip.

Ensure that the head of tail nail is set under the nail stopper of nail feeder.

Tail Nail Nail Stopper

The Nailer is now ready to operate.

NAILER OPERATION

Nail Feeder

NOTE:

Stop Lever

Read section titled “SAFETY”(pages 4 – 6).

DANGER

Always wear eye protector which conforms to ANSI Z87.1 specifications.

Use nail strip at least 5 nails remaining.

Set heads of nails overlapped as shown in the below figure.

WARNING

Never point Nailer toward yourself or anyone else.

Never carry with finger on trigger.

Remove finger from trigger when not driving nails.

Never place your hands or feet closer than 8 inches (200 mm) from firing head when using.

Do not drive nails on top of other nails or with Nailer at too steep of an angle; nails can ricochet and hurt someone.

In order to avoid double fire or unwanted ejection of a nail due to bouncing of the Nailer.

1)do not push Nailer on workpiece with strong force;

2)take Nailer away from workpiece using recoil;

3)release trigger quickly when performing trigger fire.

Do not drive nails into thin boards or near corners and edges of workpiece. Nails can be driven through or away from workpiece and hit someone.

Never drive nails from both sides of a wall at the same time. Nails can be driven into and through the wall and hit a person on the opposite side.

Never use Nailer which is defective or operating abnormally.

Do not use Nailer as hammer.

— 12 —

Image 12

Contents Mode D’EMPLOI ET Instructions DE Securite PeligroContents Definitions of Signal Words Important InformationSafety Always Wear EYE Protector Never USE Bottled GasesNever Point Nailer Toward Yourself or Anyone Else Never Carry with Finger on TriggerKeep Work Area Clean Check for Live WiresStore Nailer Properly Never USE in Presence of Flammable Liquids or GasesEMPLOYER’S Responsibilities Disconnect AIR Hose from Nailer WhenMaintain Nailer with Care Stay AlertOperation Name of PartsSpecifications AccessoriesStandard Accessories Nail SelectionOptional Accessories ApplicationsBefore Operation Working EnvironmentTesting the Nailer LubricationCold Weather Care Air consumptionAdjusting AIR Pressure Loading NailsNailer Operation Methods of Operation Adjusting the Nailing Depth Using the Nose CAPChanging the Exhaust Direction Disconnect AIR Hose from NailerMaintenance Maintenance and InspectionService and Repairs Action WHY HOW Problem Check Method CorrectionDefinition DES Mots DE Signalisation Information ImportanteSecurite AvertissementRanger LE Cloueur Correctement Maintenir L’AIRE DE Travail PropreEloigner LES Visiteurs Porter UN Habillement ApproprieResponsabilites DE L’EMPLOYEUR Debrancher LE Tuyau D’AIR DU Cloueur QuandEntretenir Soigneusement LE Cloueur Rester SUR SES GardesUtilisation NOM DES PiecesAccessoires Avertissement Accessoires StandardSelection DES Clous Accessoires EN Option Avant L’UTILISATIONEnvironnement DE Travail Avertissement Alimentation D’AIRGraissage Entretien PAR Temps FroidEssai DU Cloueur Consommation d’airReglage DE LA Pression D’AIR Avertissement Chargement DES Clous Avertissement LE Cloueur NE Doit PAS Fonctionner LE Cloueur Doit FonctionnerUtilisation DU Cloueur Methodes D’UTILISATION Reglage DE LA Profondeur DE Clouage Changement DU Sens ’ECHAPPEMENTUtilisation DU Capuchon DE BEC Debrancher LE Tuyau D’AIR DU CloueurEntretien Entretien ET InspectionEntretien ET Reparations Avertissement Inspection du magasinProbleme Verification Correction Action Pourquoi CommentInformación Importante Definición DE LAS Palabras ClaveSeguridad AdvertenciaUtilice Siempre Gafas Protectoras Para LOS Ojos No Utilice Nunca Bombonas DE GASGuarde Adecuadamente EL Martillo Neumático Mantenga EL Área DE Trabajo LimpiaMantenga a LOS Visitantes Alejados 11. Vístase AdecuadamenteResponsabilidades DEL Empresario Permanezca AlertaManeje Correctamente EL Martillo Neumático Mantenga EL Martillo Neumático CON CuidadoOperación NomenclaturaEspecificaciones Selección DE PuntasAccesorios Advertencia Accesorios EstándarAccesorios Opcionales AplicacionesAntes DE LA Operación Entorno DE Trabajo AdvertenciaLubricación Cuidados Para Climas FríosPrecaución Prueba DEL Martillo Neumático PeligroAjuste DE LA Presión DE Aire Advertencia Carga DE Puntas AdvertenciaOperación DEL Martillo Neumático Métodos DE Operación Ajuste DE LA Profundidad DE Clavado Cambio DEL Sentido DEL Aire DE EscapeDesconecte LA Manguera DE Aire DEL Martillo Neumático Utilice Siempre Gafas Protectoras Para LOS OjosUtilización DE LA Tapa Para EL Morro Mantenimiento Mantenimiento E InspecciónMantenimiento E Inspección Advertencia Inspección del cargadorProblema Método DE Comprobación Solución Acción Para CómoEspañol 3MM 4MM5MM 6MMKestrel Road Mississauga on L5T 1Z5