Hitachi NR90AA instruction manual Maintenance and Inspection, Service and Repairs

Page 15

English

MAINTENANCE

NOTE:

The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer.

Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer.

MAINTENANCE AND INSPECTION

Read section titled “SAFETY” (pages 4 – 6).

WARNING

Disconnect air hose and remove all nails from Nailer when:

1)doing maintenance and inspection; and

2)clearing a jam.

1.Inspecting the magazine

1DISCONNECT AIR HOSE.

2Clean the magazine. Remove plastic tips or wooden tips which may have accumulated in the magazine. Lubricate it with Hitachi pneumatic tool lubricant.

Nail Feeder

3. WARNING LABEL

Change the WARNING LABEL if missing or damaged. A new WARNING LABEL is available from a Hitachi authorized service center.

Warning

Label

1

4.Maintenance chart (See page 16)

5.Operator troubleshooting (See page 16)

SERVICE AND REPAIRS

Magazine

CAUTION

Disconnect air hose

WARNING

Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer.

Use only parts supplied or recommended by Hitachi for repair.

Check that the nail feeder slides smoothly by pulling it with finger.

If not smooth, nails can be driven at an irregular angle and hurt someone.

2. Storing

When not in use for an extended period, apply a thin coat of the lubricant to the steel parts to avoid rust.

Do not store the Nailer in a cold weather environment. Keep the Nailer in a warm area.

When not in use, the Nailer should be stored in a warm and dry place.

Keep out of reach children.

All quality Nailers will eventually require servicing or replacement of parts because of wear from normal use.

NOTE:

Specifications are subject to change without any obligation on the part of HITACHI.

— 15 —

Image 15

Contents Peligro Mode D’EMPLOI ET Instructions DE SecuriteContents Important Information Definitions of Signal WordsNever Carry with Finger on Trigger SafetyAlways Wear EYE Protector Never USE Bottled Gases Never Point Nailer Toward Yourself or Anyone ElseNever USE in Presence of Flammable Liquids or Gases Keep Work Area CleanCheck for Live Wires Store Nailer ProperlyStay Alert EMPLOYER’S ResponsibilitiesDisconnect AIR Hose from Nailer When Maintain Nailer with CareName of Parts OperationNail Selection SpecificationsAccessories Standard AccessoriesWorking Environment Optional AccessoriesApplications Before OperationAir consumption Testing the NailerLubrication Cold Weather CareLoading Nails Adjusting AIR PressureNailer Operation Methods of Operation Disconnect AIR Hose from Nailer Adjusting the Nailing DepthUsing the Nose CAP Changing the Exhaust DirectionMaintenance Maintenance and InspectionService and Repairs Problem Check Method Correction Action WHY HOWInformation Importante Definition DES Mots DE SignalisationAvertissement SecuritePorter UN Habillement Approprie Ranger LE Cloueur CorrectementMaintenir L’AIRE DE Travail Propre Eloigner LES VisiteursRester SUR SES Gardes Responsabilites DE L’EMPLOYEURDebrancher LE Tuyau D’AIR DU Cloueur Quand Entretenir Soigneusement LE CloueurNOM DES Pieces UtilisationAccessoires Avertissement Accessoires StandardSelection DES Clous Alimentation D’AIR Accessoires EN OptionAvant L’UTILISATION Environnement DE Travail AvertissementConsommation d’air GraissageEntretien PAR Temps Froid Essai DU Cloueur LE Cloueur Doit Fonctionner Reglage DE LA Pression D’AIR AvertissementChargement DES Clous Avertissement LE Cloueur NE Doit PAS FonctionnerUtilisation DU Cloueur Methodes D’UTILISATION Debrancher LE Tuyau D’AIR DU Cloueur Reglage DE LA Profondeur DE ClouageChangement DU Sens ’ECHAPPEMENT Utilisation DU Capuchon DE BECInspection du magasin EntretienEntretien ET Inspection Entretien ET Reparations AvertissementAction Pourquoi Comment Probleme Verification CorrectionDefinición DE LAS Palabras Clave Información ImportanteNo Utilice Nunca Bombonas DE GAS SeguridadAdvertencia Utilice Siempre Gafas Protectoras Para LOS Ojos11. Vístase Adecuadamente Guarde Adecuadamente EL Martillo NeumáticoMantenga EL Área DE Trabajo Limpia Mantenga a LOS Visitantes AlejadosMantenga EL Martillo Neumático CON Cuidado Responsabilidades DEL EmpresarioPermanezca Alerta Maneje Correctamente EL Martillo NeumáticoNomenclatura OperaciónAccesorios Estándar EspecificacionesSelección DE Puntas Accesorios AdvertenciaEntorno DE Trabajo Advertencia Accesorios OpcionalesAplicaciones Antes DE LA OperaciónPrueba DEL Martillo Neumático Peligro LubricaciónCuidados Para Climas Fríos PrecauciónCarga DE Puntas Advertencia Ajuste DE LA Presión DE Aire AdvertenciaOperación DEL Martillo Neumático Métodos DE Operación Utilice Siempre Gafas Protectoras Para LOS Ojos Ajuste DE LA Profundidad DE ClavadoCambio DEL Sentido DEL Aire DE Escape Desconecte LA Manguera DE Aire DEL Martillo NeumáticoUtilización DE LA Tapa Para EL Morro Inspección del cargador MantenimientoMantenimiento E Inspección Mantenimiento E Inspección AdvertenciaAcción Para Cómo Problema Método DE Comprobación SoluciónEspañol 6MM 3MM4MM 5MMKestrel Road Mississauga on L5T 1Z5