Black & Decker 395136-00 Bevel Setting Type of CUT, Aluminum Cutting Carbide Tipped Blade only

Page 17

395136-00,03,BT1500 6/22/04 9:05 AM Page 17

INSTRUCTIONS FOR CUTTING CROWN MOLDING LAYING FLAT AND USING THE COMPOUND FEATURES

1. Molding laying with broad back surface down flat on saw table

PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!

2.The settings below are for All Standard (U.S.) crown molding with 52° and 38° angles.

BEVEL SETTING

TYPE OF CUT

SPECIAL CUTS

NEVER MAKE ANY CUTS UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE.

LEFT SIDE, INSIDE CORNER:

33.85° 1. Top of molding against fence

2.Miter table set right 31.62°

3.Save left end of cut

RIGHT SIDE, INSIDE CORNER:

33.85° 1. Bottom of molding against fence

2.Miter table set left 31.62°

3.Save left end of cut

LEFT SIDE, OUTSIDE CORNER:

33.85° 1. Bottom of molding against fence

2.Miter table set left 31.62°

3.Save right end of cut

RIGHT SIDE, OUTSIDE CORNER:

33.85° 1. Top of molding against fence

2.Miter table set right 31.62°

3.Save right end of cut

When setting bevel and miter angles for all compound miters, remember that:

The angles presented for crown moldings are very precise and difficult to set exactly. Since they can easily shift slightly and very few rooms have exactly square corners, all settings should be tested on scrap molding.

ALUMINUM CUTTING (CARBIDE TIPPED BLADE ONLY)

Aluminum extrusions such as those used when making aluminum screens and storm windows can easily be cut with your saw using the proper blade designed for non-ferrous metal cutting. Position the material so that you will be cutting the thinnest cross section, as shown in Figure 14. Figure 15 illustrates the wrong way to cut these extrusions. Use a wax lubricant when cutting aluminum such as Johnson’s Stick Wax No.140. Apply the stick wax directly to the saw blade before cutting. Never apply stick wax to a moving blade.

The wax, available at most hardware stores and industrial mill supply houses, provides proper lubrication and keeps chips from adhering to the blade.

Be sure to properly secure work. Certain workpieces, due to their size, shape or surface finish, may require the use of a clamp, jig or fixture to prevent movement during the cut.

BOWED MATERIAL

When cutting bowed material always position it as shown in Figure 16 and never like that shown in Figure 17. Positioning the material incorrectly will cause it to pinch the blade near the completion of the cut.

CUTTING PLASTIC PIPE AND OTHER ROUND CROSS- SECTIONAL MATERIAL

Plastic pipe can be easily cut with your saw. It should be cut just like

17

If you have any questions, call 1-800-54-HOW-TO

Image 17
Contents HOW-TO Parts Description Figures 1,2 Operating Handle 31.6 22.5 395136-00,03,BT1500 6/22/04 904 AM 31.6 Work Extensions Stop Block Extensiones Bloque DE Tope Safety Warnings Double Insulation Important Safety InstructionsSafety Instructions Polarized Plugs Safety Instructions For All ToolsAdditional Safety Rules For Miter Saws 395136-00,03,BT1500 6/22/04 905 AM On Guard Danger Keep Away from BLADE. Danger Electrical ConnectionUnpacking Your Saw Installing a New Saw Blade SpecificationsFamiliarization Bench MountingAttaching Work Extensions Assembling and Adjusting Your Saw AdjustmentsAttaching Dust BAG Attaching Stop BlockBevel Stop Adjustment Miter Pointer Adjustment Bevel PointersFence Adjustment Turn Off and Unplug the Miter SawOperation BrushesBevel Cuts CrosscutsQuality of CUT Clamping the WorkpieceCutting Trim Molding and Other Frames Pretesting with Scrap Material is Extremely ImportantCutting Compound Miters Cutting Crown MoldingBowed Material Bevel Setting Type of CUTAluminum Cutting Carbide Tipped Blade only Maintenance Trouble Shooting GuidePerform all maintenance with miter saw unplugged Be Sure to Follow Safety Rules and InstructionsAccessories Service InformationFull Two-Year Home Use Warranty NO. BT1500 Description des pièces figures 1 etConsignes de sécurité importantes Consignes de sécurité double isolationConsignes de sécurité tous les outils Consignes de sécurité fiches polariséesConsignes de sécurité additionnelles scie à onglets Raccordement électrique SUR LA Plaque DE Retenue DU Dispositif DE ProtectionMontage sur un établi Déballage de la scieFamiliarisation Fixation du sac à poussière Installation d’une lame neuveFixation de la butée Fixation des rallongesArrêter ET Débrancher LA Scie À Onglets Balais Débrancher la fiche de la prise murale Visibilité et déclenchement du protège-lameFonctionnement InterrupteurCoupes en biseau Méthode de coupeQualité de la coupe Position du corps et des mains figureCoupe À Onglets Combinée Fixation de l’ouvrage Arrêter et débrancher la scieSupport de longs ouvrages Arrêter et débrancher la scie Biseau Coupe Côté GAUCHE, Coin Intérieur Coupe DE Moulures EN CouronneCoupes particulières Coupe de l’aluminiumGuide de dépannage Garantie Complète DE Deux ANS Pour L’USAGE Domestique Renseignements Concernant LE ServiceRemplacement Gratuit DE L’ÉTIQUETTE ’AVERTISSEMENT Advertencias de seguridad Doble aislamiento Instrucciones importantes de seguridadSiempre Utilice Anteojos DE SEGURIDAD. También utilice Advertencias de seguridad Clavijas polarizadasSe haya detenido completamente EN LA Guia Movil Siempre Ajuste LA Guia EN LA Carcaza DEL MotorEN LA Guarda Peligro Alejese DE EL Disco EN LA Placa DE Retención DEL ProtectorCapacidad DE Corte Instalación de un disco nuevoInstalación de la bolsa para polvo Ensamblaje y ajuste de su sierraInstalación del tope Instalación de las extensiones de trabajoAjuste DE LA Escala DE Inglete DesconectadaAjuste DEL Indicador DE Inglete Ajuste DEL Tope DE BiselOperación CarbonesCalidad DEL Corte Cortes DE BiselPosicion DE Cuerpo Y Manos Vease Figura Sujecion DE LA Pieza DE TrabajoCorte DE MARCOS, CAJAS, Y Otros Proyectos DE Cuatro Lados Soporte Para Piezas LargasCorte DE Molduras Y Otros Marcos Corte DE Inglete CompuestoCorte DE Aluminio Corte DE Molduras DE RemateAjuste DE Bisel Tipo DE Corte Mantenimiento Guía para la solución de problemas frecuentesCorte DE Tuberia DE Plástico ImportanteGarantia Para USO Doméstico POR DOS Años Completos Informacion Respecto EL ServicioMEXICO, D.F CULIACAN, SINMERIDA, YUC MONTERREY, N.L395136-00,03,BT1500 6/22/04 905 AM 395136-00,03,BT1500 6/22/04 905 AM