Black & Decker instruction manual 395136-00,03,BT1500 6/22/04 905 AM

Page 9

395136-00,03,BT1500 6/22/04 9:05 AM Page 9

DO-Be sure all blade and clamp washers are clean and recessed sides of collars are against blade. Tighten arbor screw securely.

DO-Keep saw blade sharp.

DO-Keep motor air slots free of chips and dirt.

DO-Use blade guards at all times.

DO-Keep hands out of path of saw blade.

DO-Shut off power, disconnect cord from power source and wait for saw blade to stop before servicing or adjusting tool.

DO-Support long work with an outboard tool rest.

DO-Use only 10 inch diameter blades.

DON’T-Attempt to operate on anything but designated voltage.

DON’T-Operate unless all clamp handles are tight.

DON’T-Use blades larger or smaller than those which are recommended.

DON’T-Wedge anything against fan to hold motor shaft.

DON’T-Force cutting action. (Stalling or partial stalling of motor can cause major damage. Allow motor to reach full speed before cutting.)

DON’T-Cut ferrous metals (Those with any iron or steel content) or any masonry.

DON’T-Use abrasive wheels. The excessive heat and abrasive particles generated by them will damage saw.

DON’T-Allow anyone to stand behind saw.

DON’T-Apply lubricants to the blade when it’s running.

DON’T-Place either hand in the blade area when the saw is connected to the power source.

DON’T-Use blades rated less than 5500 R.P.M.

DON’T-Attempt to cut small pieces (hand within 6" of blade) without clamping.

DON’T-Operate saw without guards in place.

DON’T-Perform any operation freehand.

DON’T-Reach around or behind saw blade.

DON’T-Place hands closer than 6 inches from the saw blade.

DON’T-Reach underneath the saw unless it is turned off and unplugged. The saw blade is exposed on the underside of the saw.

DON’T-Move either hand from saw or workpiece or raise arm until blade has stopped.

DON’T-Use without Kerf Plate or when kerf slot is wider than 3/8".

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber. (CCA)

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

9

If you have any questions, call 1-800-54-HOW-TO.

Image 9
Contents HOW-TO Parts Description Figures 1,2 Operating Handle 31.6 22.5 395136-00,03,BT1500 6/22/04 904 AM 31.6 Work Extensions Stop Block Extensiones Bloque DE Tope Safety Warnings Double Insulation Important Safety InstructionsSafety Instructions Polarized Plugs Safety Instructions For All ToolsAdditional Safety Rules For Miter Saws 395136-00,03,BT1500 6/22/04 905 AM Electrical Connection Unpacking Your SawOn Guard Danger Keep Away from BLADE. Danger Installing a New Saw Blade SpecificationsFamiliarization Bench MountingAttaching Work Extensions Assembling and Adjusting Your Saw AdjustmentsAttaching Dust BAG Attaching Stop BlockBevel Stop Adjustment Miter Pointer Adjustment Bevel PointersFence Adjustment Turn Off and Unplug the Miter SawOperation BrushesBevel Cuts CrosscutsQuality of CUT Clamping the WorkpieceCutting Trim Molding and Other Frames Pretesting with Scrap Material is Extremely ImportantCutting Compound Miters Cutting Crown MoldingBevel Setting Type of CUT Aluminum Cutting Carbide Tipped Blade onlyBowed Material Maintenance Trouble Shooting GuidePerform all maintenance with miter saw unplugged Be Sure to Follow Safety Rules and InstructionsService Information Full Two-Year Home Use WarrantyAccessories NO. BT1500 Description des pièces figures 1 etConsignes de sécurité importantes Consignes de sécurité double isolationConsignes de sécurité tous les outils Consignes de sécurité fiches polariséesConsignes de sécurité additionnelles scie à onglets Raccordement électrique SUR LA Plaque DE Retenue DU Dispositif DE ProtectionDéballage de la scie FamiliarisationMontage sur un établi Fixation du sac à poussière Installation d’une lame neuveFixation de la butée Fixation des rallongesArrêter ET Débrancher LA Scie À Onglets Balais Débrancher la fiche de la prise murale Visibilité et déclenchement du protège-lameFonctionnement InterrupteurCoupes en biseau Méthode de coupeQualité de la coupe Position du corps et des mains figureFixation de l’ouvrage Arrêter et débrancher la scie Support de longs ouvrages Arrêter et débrancher la scieCoupe À Onglets Combinée Biseau Coupe Côté GAUCHE, Coin Intérieur Coupe DE Moulures EN CouronneCoupes particulières Coupe de l’aluminiumGuide de dépannage Renseignements Concernant LE Service Remplacement Gratuit DE L’ÉTIQUETTE ’AVERTISSEMENTGarantie Complète DE Deux ANS Pour L’USAGE Domestique Advertencias de seguridad Doble aislamiento Instrucciones importantes de seguridadSiempre Utilice Anteojos DE SEGURIDAD. También utilice Advertencias de seguridad Clavijas polarizadasSe haya detenido completamente EN LA Guia Movil Siempre Ajuste LA Guia EN LA Carcaza DEL MotorEN LA Guarda Peligro Alejese DE EL Disco EN LA Placa DE Retención DEL ProtectorCapacidad DE Corte Instalación de un disco nuevoInstalación de la bolsa para polvo Ensamblaje y ajuste de su sierraInstalación del tope Instalación de las extensiones de trabajoAjuste DE LA Escala DE Inglete DesconectadaAjuste DEL Indicador DE Inglete Ajuste DEL Tope DE BiselOperación CarbonesCalidad DEL Corte Cortes DE BiselPosicion DE Cuerpo Y Manos Vease Figura Sujecion DE LA Pieza DE TrabajoCorte DE MARCOS, CAJAS, Y Otros Proyectos DE Cuatro Lados Soporte Para Piezas LargasCorte DE Molduras Y Otros Marcos Corte DE Inglete CompuestoCorte DE Molduras DE Remate Ajuste DE Bisel Tipo DE CorteCorte DE Aluminio Mantenimiento Guía para la solución de problemas frecuentesCorte DE Tuberia DE Plástico ImportanteGarantia Para USO Doméstico POR DOS Años Completos Informacion Respecto EL ServicioMEXICO, D.F CULIACAN, SINMERIDA, YUC MONTERREY, N.L395136-00,03,BT1500 6/22/04 905 AM 395136-00,03,BT1500 6/22/04 905 AM